Related Manuals for Envision EN7410
Summary of Contents for Envision EN7410
- Page 1 EN7410 17” TFT LCD Monitor User’s Manual By Envision Peripherals Inc. www.ENVISIONdisplay.com...
-
Page 2: For Your Safety
4. Consult the dealer or an experienced radio/TV technician for help. ® As an ENERGY STAR Partner Envision Peripherals Inc. has determined ® that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. - Page 3 PRECAUTIONS: • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
- Page 4 circuit parts causing a fire or electric shock. Never spill liquids on the monitor. • Do not attempt to service the monitor by yourself. Opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. •...
-
Page 5: General Notes
GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. - Page 6 OTHER NOTES • The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. This contact may scratch or damage the screen. These damages are not covered under the warranty. •...
-
Page 7: Reference Information
Disclaimer Envision Peripherals Inc. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Envision Peripherals Inc. reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. -
Page 8: Table Of Contents
Table of Contents 1 Important Safety Instructions ...i 2 Features...2 3 Unpacking the Monitor ...3 4 Hardware Installation ...4 5 Windows driver installation ...5 6 Setting the Display Resolution ...6 Choosing the Best Resolution ... 6 Supported Graphics Modes and Refresh Rate Selection... -
Page 9: Important Safety Instructions
Important Safety Instructions Please read the following safety instructions before installing or cleaning your Envision monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. -
Page 10: Features
♦ High Brightness – 300 cd/m ♦ High Contrast Ratio – 400:1 (typical) ♦ True Colour Display With FRC support for 16.7M colours, the Envision EN7410 monitor offers you better image quality. ♦ High Quality Expansion With any resolution within the monitor’s specified range, your Envision EN7410 monitor can expand the image to full screen. -
Page 11: Unpacking The Monitor
Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately Monitor 1 pc 1 pc 1 pc 1 pc Signal Cable Power Cable CD User’s (Quick Start Manual... -
Page 12: Hardware Installation
If you are unsure, please contact your electricity supplier. To install your Envision EN7410 monitor: 1. Make sure that the power to the computer and the power to the monitor are both turned off. -
Page 13: Windows Driver Installation
Windows driver Installation The Envision EN7410 is fully Windows compatible so no specific windows drivers are required to be loaded. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add New Hardware wizard. -
Page 14: Setting The Display Resolution
LCD. In the case of the EN7410 the LCD resolution is 1280 x 1024 pixels. This is also known as the “native” resolution of the monitor. Lower resolutions can be displayed at full screen through an interpolation circuit. -
Page 15: Supported Graphics Modes And Refresh Rate Selection
For best results, it is important that you set the graphics adaptor to use one of the monitor’s preset display modes shown in Table 1 on the next page. Other graphics signals may be displayed poorly or not at all. Note that the EN7410’s preset modes correspond to VESA or Apple Macintosh standard graphics signals for these resolutions. - Page 16 caused by the signal from the VGA card if it does not correspond with the usual standard. This is not however, a problem with the monitor. If it is still visible after using the Automatic adjustment, you can usually improve the displayed image by manually adjusting the phase, horizontal position and pixel frequency settings using the "Geometry"...
-
Page 17: Adjusting The Monitor
Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the Auto button for 2 seconds. This only works reliably if the graphics adaptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying a suitable stationary image (such as the windows desktop). - Page 18 (from left to right) Menu Enter OSD menu. Enter submenus or select items within OSD menu. Move the selection cursor upwards within the OSD menu. Move the selection cursor downwards within the OSD menu. Adjust OSD functions. (Decrease) Adjust OSD functions. (Increase) SELECT Automatically adjust the vertical, horizontal position, pixel phase and pixel clock.
-
Page 19: Position Adjustment
Tracking Adjustment Position Adjustment CLOCK: Adjust to minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE: Adjust to remove any horizontal distortion, and clear or sharpen the image of characters. V-Position: Adjust the vertical position of the picture. -
Page 20: Color Adjustment
Color Adjustment Other There are three items for color adjustment: 9300K: Bluish white 6500K: Reddish white User defined: Red, Green, Blue. Adjust to set your own color level. LANGUAGE: Multi- Language selection OSD POSITION: Adjust the OSD window position on the screen. INFORMATION: “ON”... -
Page 21: Frequently Asked Questions
The most common cause of this problem is a loose VGA signal cable or ♦ connector. Check that the cable is securely connected to the computer. Check the VGA signal cable for damage. If any pins are bent or broken off, ♦ contact your dealer or an authorized Envision Peripherals Inc. service agent... - Page 22 No image is displayed, what can I do? Check that the light (LED) next to the monitor’s power button is lit and is ♦ green in colour. If the LED is green, press the MENU button on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Setting the Display Resolution and reset the graphics card to one of the monitor’s supported graphics signals.
- Page 23 The display shows OUT OF FREQUENCY error message: Read chapter 6, Setting the Display Resolution, and select a graphics ♦ signal with the correct resolution and refresh rate.
-
Page 24: Specifications
Specifications Envision EN7410 Model: Display Characteristics Display Type Viewable Diagonal Area Native (Maximum) Resolution Colors Contrast Ratio Brightness Response Time Viewing Angle (Horizontal, Vertical) Dot Pitch User Interface Controls On-Screen Display Functions 17“ active matrix Thin Film Transistor Liquid Crystal Display 43.18 cm / 17”... -
Page 25: Input Signal
Input Signal Line Frequency Image Frequency (Refresh Rate) Video Signal Synchronization Signal Connection Physical Characteristics Power Management Maximum Power Consumption Power Saving Mode Operating Voltage Dimensions (W x H x D) Weight Temperature (Operating) Air Humidity (Operating) Regulatory Certification Safety EMI/EMC Other 31 - 83kHz multi-frequency...