Related Manuals for Envision EN7400e
Summary of Contents for Envision EN7400e
- Page 1 EN7400e EN7400e 17 inch TFT LCD Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONdisplay.com Before operating your monitor, please read this manual thoroughly. EN7400e 12OCT04...
-
Page 2: Fcc Statement
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. EN7400e For Your Safety Notice 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. - Page 3 Overloading can result in fire or electric shock. • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) EN7400e Precautions pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet...
-
Page 4: Special Notes On Lcd Monitors
EPI service center for replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. EN7400e For Your Safety General Notes • Do not install the monitor near heat sources such as radiators or air ducts. -
Page 5: Before You Operate The Monitor
EN7400e Package Contents The box that your monitor was shipped in should have included the following items: 1. EN7400e LCD Monitor 2. Power Cord 3. Windows 95/98/2000/ME/XP INF Driver Disk 4. Quick Start Guide 5. Booklet (Containing Warranty & Safety... - Page 6 4. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. EN7400e Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required).
- Page 7 Before You Operate the Monitor EN7400e Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting See next page for further installation instructions. arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1.
-
Page 8: Install An Optional Wall Mounting Arm (Not Supplied)
3. Insert the power cable into the slot on the back of the monitor. EN7400e The Envisionl EN7400e is compatible with the Ergotron line of mounting and arm solutions. Contact Ergotron at 800-888-8458 or visit their web site at www.ergotron.com for more information on the many ways on which you can mount your Envision LCD monitor. -
Page 9: Adjusting The Viewing Angle
It may cause damage or breakage. • Be careful to avoid pinching your hand in the swivel base. EN7400e How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive. -
Page 10: Front Panel Buttons
MENU: Press this button to open the OSD window or exit from the OSD window. EN7400e Operating Instructions Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. -
Page 11: Adjusting The Osd Settings
3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settings of the function. EN7400e Operating Instructions 5. To save and exit, highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds. -
Page 12: Plug & Play Ddc1/2B Feature
Operating Instructions EN7400e Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. -
Page 13: Technical Support (Faq)
5 Dark Sub-pixels or combination of 8 Dark & Bright. The panel used on this product has a total of 3,932,160 sub-pixels. So even the maximum allowed of 6 bad sub-pixels would only amount to a very small 0.0002% of the total sub-pixels EN7400e Possible Solution EN7400e 12OCT04... - Page 14 • Make sure the video cable is properly connected to the computer. If the connector is loose, tighten the connector's two screws. • Inspect the video cable and make sure that none of the pins are bent. EN7400e Technical Support (FAQ) Possible Solution...
-
Page 15: Resolution Chart
640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 EN7400e Technical Support (FAQ) Possible Solution Vertical Frequency 60 Hz 70 Hz 70 Hz 70 Hz 72.8 Hz... -
Page 16: Specifications
Response time Video Separate Sync. H-Frequency V-Frequency Display Colors Dot Clock Maximum Resolution EN7400e Appendix Plug & Play TFT Color LCD Input Connector 17" (43.2 cm) Diagonal Input Video Signal 0.264 mm (H) x 0.264 mm (V) Maximum Screen Size 140°... - Page 17 Brightness Focus Clock H-Position V-Position Language Dos-mode Resolution Selected 6500° K 7800° K RGB Color temp. Recall Exit EPA ENERGY STAR® Power Consumption 45 Watts (Maximum) Regulatory UL, CSA, FCC, TÜV/ Compliance GS, CE, XP Logo EN7400e Appendix EN7400e 12OCT04...
-
Page 18: Factory Preset Timing Table
800 × 600 832 × 624 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA 1280 x 1024 1280 x 1024 EN7400e Appendix Resolution Horizontal (in pixels) Frequency 31.47 kHz 31.47 kHz 31.47 kHz 35.00 kHz 37.50 kHz... -
Page 19: Connector Pin Assignment
Connector Pin Assignment Pin Number EN7400e Appendix Description Pin Number Green Blue Ground Ground R-Ground G-Ground B-Ground EN7400e Description Detect Cable DDC-Serial Data H-Sync V-Sync DDC-Serial Clock 12OCT04...