MTD World Tiller - Series 240 Operator's Manual
World tiller
Hide thumbs
Also See for World Tiller - Series 240:
- Operator's manual (29 pages) ,
- Operator's manual (20 pages) ,
- Operator's manual (18 pages)
Related Manuals for MTD World Tiller - Series 240
Summary of Contents for MTD World Tiller - Series 240
- Page 1 SafeOperationPractices • Set-Up• Operation• Maintenance • Service• Troubleshooting• Warranty World Tiller m Series 240 MTD LLC, P.O. BOX 361131 CLEVELAND, OHiO 44136-0019 PrintedIn USA FormNo.769-05429B (February 15,2010)
-
Page 2: Customer Support
Choose from the options below: Visit us on the web at www.mtdproducts.com Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683 Write to MTD LLC • EO. Box 361131 • Cleveland, OH • 44136-0019... -
Page 3: Important Safe Operation Practices
importantSafeOperation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. -
Page 4: Maintenance And Storage
When practical, remove gas-powered equipment After striking a foreign object, stop the engine, disconnect from the truck or trailer and refuel it on the ground. the spark plug wire and ground against the engine. If this is not possible, then refuel such equipment Thoroughly inspect the machine for any damage. -
Page 5: Spark Arrester
If the fuel tank has to be drained, do this outdoors. SparkArrester Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment. internal combustion engine and should not be used ARNING! According to the Consumer Products Safety Commission on or near any unimproved This machine... -
Page 6: Safety Symbols
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting assemble and operate... -
Page 7: Assembly And Setup
Assembly & Set-Up Contents of Carton OneTiller One 20 oz. bottle SAE 30W oil One Tiller Operator's Manual One Engine Operator's Manual NOTE:The tiller is shipped without gasoline or oil in the engine. Position the upper handle onto the lower handle, Step A in Fill up gasoline and oil as instructed in the accompanying engine... - Page 8 4. Insert theclutch c able h andle fitting into thehole onthe Set-tip right s ide oftheupper handle. See Fig. 3-3. (;as & 0il Fill-Up Service the engine with gasoline and oil as instructed in the separate engine manual packed with your tiller. Read the instructions carefully.
-
Page 9: Controls And Features
Controls a nd Features Tine Clutch Recoil Starter Clutch Cable Handlebar Height Adjustment Rea r Wheel Figure 4-1 TineClutchControl RearWheelwith DepthStake The rear wheel can be raised and lowered for transport The clutch control lever is located on the upper handle. storage. -
Page 10: Operation
Operation The working depth of the machine may be predetermined WARNING! Read, understand, and follow all setting the depth stake so that the wheels are about four inches instructions and warnings posted on the machine from the ground when the tines and depth stake are resting on and in this manual before operating. - Page 11 In some soils, the desired depth is obtained the first time over For proper decaying action, fertilizer should be applied the garden. In other soils, the desired depth is obtained by going worked in with the mulch materials. Breaking up leaves and straw over the garden two or three times.
-
Page 12: Maintenance And Adjustments
Maintenance& Adjustments WARNING! Before inspecting, cleaning or servicing Adjustments the tiller, shut off the engine and wait for all moving TineWidth parts to come to a complete stop. Disconnect spark plug. Failure to follow these instructions The tilling width of the unit is 22 inches. Tilling width properly can result in serious personal injury or... -
Page 13: Off-Season Storage
DepthStake The depth stake acts as a brake for the tiller and controls depth and speed at which the machine will operate, Figure 6-2. Remove the clevis and cotter pins, raise or lower the depth stake, then reattach pins to secure. Figure 6-2 Off-Season Storage If the tiller will not be used fora period... -
Page 14: Engine Maintenance
EngineMaintenance Periodic inspection and adjustment of the engine is essential high level performance is to be maintained. Regular maintenance any maintenance. To prevent accidental start-up, ARNING: Shut offthe engine before performing disconnect the spark plug boot. will also ensure a long service life. The required service intervals and the kind of maintenance to be performed... -
Page 15: Oil Recommendations
Oil Recommendations Oil Service Check oil level regularly. NOTE:This engine is shipped without gasoline or oil in the engine. Running the engine with insufficient oil can cause Be sure correct oil level is maintained. Check every five serious engine damage and void the engine warranty. -
Page 16: Spark Plug Service
Remove the thumb screw and the air cleaner cover. Remove the elements and separate them. See Fig. 10-2. muffler will be very hot. Be careful not to touch the ARNING: If the engine has been running, Replace paper element when dirty or damaged. Clean muffler. -
Page 17: Fuelfilter Service
FuelFilter Service Storage The fuel filter cannot be cleaned and must be replaced once a Engines stored between 30 and 90 days need to be treated with year or every 100 operating hours; more often if run with old a gasoline stabilizer and engines stored over 90 days need to be... -
Page 18: Belt Replacement
Replace with a factory-approved OEM belt. See the retailer from which you purchased your tiller, an authorized MTD Service Dealer, or call 1-800-800-7310 for information regarding price and availability. Remove the belt cover and engine by removing the six... -
Page 19: Troubleshooting
Troubleshooting Problem Cause Remedy Engine runs erratic 1. Spark plug wire loose 1. Connect and tighten spark plug wire 2. Move choke lever to OFF 2. Unit running on CHOKE 3. Blocked fuel line or stale fuel 3. Clean fuel line; fill tank with clean, fresh gasoline 4. -
Page 20: Illustrated Parts List
illustrated PartsList 47 /'... - Page 21 Handle, Frame & Wheel A ssembly Description Part Number Part Number Ref. Description Ref, I 649-04030-0638 749-04265-0638 Depth Stake Tube Upper Handle 710-0136 711-04520 Axle Shaft Hex Head Cap Screw, 1/4-20x 1.75 710-1007 649-04029-0638 Lower Handle Self Tapping Screw, 3/8-16 x 1.50 911-0415 Clevis Pin 710-04398...
- Page 22 EngineModel - 1P65LHA .144 142" 25 1 126.
- Page 23 EngineM0del - 1P65LHA R°, I R°, I Part No. Description Part No. Description 712-04212 Governor Arm Nut M6 710-04744 Self-Tapping Bolt, Hilo #12-16 X ZOO" 951-11678 Governor 931-04437 Engine Shroud 951-I0299A 710-04908 Governor Arm Bolt Recoil Starter Assembly 712-04212 Nut M6 X 10 Mm 951-11679 Governor Arm Shield...
- Page 24 EngineM0del - 1P65LHA Description Description Part Part 710-04903 951-10300 Fuel Drain Plug Fuel Cap Assembly 951-11684 Carburetor Gasket Fuel Cap 951-11527 Carburetor Insulator Sponge Insert 951-11528 Carburetor Insulator Gasket Vent Gasket 951-11520 710-05093 Carb Stud M6x92 Breather Hose Assembly 710-04982 Head Bolt M8x54 Breather Hose Clamp 951-10292...
- Page 25 EngineM0del - 1P65LltA Part No. Description Description Part 951-10298 Air Cleaner Kit 951-10846 Cylinder Head Pre-Cleaner Head Bolt M8x54 Air Filter Intake Valve Seal 951-10882 Valve Cover Gasket Air Cleaner Housing Ass'y Outer Air Filter Housing Cylinder Head Gasket 167 _ 951-11692 Inner Air Filter Housing Carburetor...
- Page 26 EngineModel - 1P65LHA Part No. Description Part No, Description 951-11689 Short Block 951-10334 Oil Fill Tube Assembly Bolt M6x14 Oil Fill Tube Breather Cover Plate Oil Fill Tube O-Ring Breather Gasket 951-10313 Valve Kit Intake Valve Upper Crankshaft Seal Mesh Screen Exhaust Valve Breather Spring Breather Valve...
-
Page 28: Limited Warranty
MANUFACTURER'S LiMiTED WARRANTY The limited warranty set forth below is given by MTD LLC with c. Routine maintenance items such as lubricants, filters, blade respect to new merchandise purchased and used in the United States sharpening, tune-ups, brake adjustments, clutch adjustments,...