Download Print this page

Lightolier END FEED AND FLOATING CANOPY MOUNTING KIT Instructions For Maintenance Reference

Flush and standoff versions for use with prospec® surface mount track systems only

Advertisement

Quick Links

READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
END FEED AND FLOATING CANOPY MOUNTING KIT - FLUSH AND STANDOFF VERSIONS
FOR USE WITH PROSPEC
CAUTION:
TURN OFF POWER AT FUSE BOX BEFORE
INSTALLING THE CANOPY KIT
END FEED MOUNTING INSTRUCTIONS
(Flush 26060WH, BK and Standoff 26061WH, BK)
Mounting the CANOPY at the end of FEED TRACK or directly above
a FEED CONNECTOR.
1. Mark CENTER LINE for TRACK through CENTER LINE of OUT-
LET BOX.
2. NOTE: The CANOPY mounts to a 3 or 4" OCTAGON OUTLET
BOX. The MOUNTING HOLES of the OUTLET BOX should be at
45° to the longitudinal axis of the TRACK. (Fig. 1)
3. Remove the KNOCK OUT PLATE from the FEED TRACK or
CONNECTOR (retain the SCREW). (Fig. 2)
4. Prepare TAB on the PLATE ASSEMBLY as follows:
• FEED TRACK: DO NOT BREAK ANY TAB. (Fig. 2)
• POWER EXTENSION, IN-LINE, "T", AND "X" CONNECTORS:
BREAK THE 90° TAB OFF THE PLATE ASSEMBLY. (Fig. 3)
• "L" CONNECTOR: BREAK THE 90° TAB AND THE STRAIGHT
TAB FROM THE PLATE ASSEMBLY. (Fig. 4)
5. Attach the PLATE ASSEMBLY onto the FEED TRACK or
CONNECTOR using the SCREW. (Fig. 2 & 3)
6. Mount the TRACK to the ceiling (see instruction sheet
IS:26000 provided with the TRACK) passing the wires through
the center of the PLATE ASSEMBLY.
7. Rotate the PLATE ASSEMBLY until the SLOTS are in-line with
the MOUNTING HOLES on the J-BOX.
8. Secure the PLATE ASSEMBLY to the J-BOX using the THIN
HEAD SCREWS. (Fig. 5)
9. Attach the GROUND WIRE on the CANOPY PLATE to the
GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 5)
10. WHEN USING THE FLUSH CANOPY 26060WH/BK.
Slide the CANOPY PLATE between the CONNECTOR and
CROSS BAR on the PLATE ASSEMBLY. For added security of
CANOPY PLATE: Drill a hole in CANOPY PLATE and secure to
ceiling with a screw.
11. WHEN USING THE STANDOFF CANOPY 26061WH/BK
Slide the CANOPY PLATE between the CROSS BAR and NUT
on the PLATE ASSEMBLY. Rotate the NUT to secure the
CANOPY PLATE against the ceiling. (Fig. 8)
NOTE: THE CROSS BAR MUST COVER THE SLOT IN
THE CANOPY PLATE AFTER ASSEMBLY.
12. Follow the instructions for wiring on the instruction sheet
included with the "FEED TRACK" or "CONNECTOR".
FIG. 5
J-BOX
®
SURFACE MOUNT TRACK SYSTEMS ONLY
CANOPY
PLAT E
GROUND
WIRE
THIN HEAD
SCREW
INSTRUCTION SHEET NO.
®
TRACK ITEM.
IS:26060
0597
TRACK UNIT
FIG. 1
KNOCK OUT
PLAT E
FIG. 2
9 0°TAB
KNOCK OUT
PLAT E
FIG. 3
CROSS BAR
9 0°TAB
KNOCK OUT
PLAT E
FIG. 4
LIGHTOLIER a GENLYTE company.
®
631 Airport Road, Fall River, MA 02720
Page 1 of 2
OUTLET BOX
MOUNTING HOLE
OUTLET BOX
LONGITUDINAL
TRACK
PLAT E
ASSEMBLY
SCREW
FEED TRACK
CROSS BAR
PLAT E
SCREW
ASSEMBLY
POWER EXTENSION
CONNECTOR
PLAT E
ASSEMBLY
STRAIGHT
TAB
" L" CONNECTOR

Advertisement

loading

Summary of Contents for Lightolier END FEED AND FLOATING CANOPY MOUNTING KIT

  • Page 1 “FEED TRACK” or “CONNECTOR”. ASSEMBLY KNOCK OUT STRAIGHT PLAT E FIG. 5 CANOPY PLAT E J-BOX “ L” CONNECTOR GROUND WIRE THIN HEAD FIG. 4 SCREW LIGHTOLIER a GENLYTE company. ® 631 Airport Road, Fall River, MA 02720...
  • Page 2 19. Follow the instructions for wiring on the instruction sheets POWER EXTENSION included with the the “FEED TRACK” or “CONNECTOR”. CONNECTOR FIG. 8 20. Assembly the DEAD END into the end of the TRACK. LIGHTOLIER a GENLYTE company. ® 631 Airport Road, Fall River, MA 02720...

This manual is also suitable for:

26060