Download Print this page

Coleman ELITE WEATHERMASTER 2000001588 Manual

2000001588

Advertisement

Quick Links

ELITE WEATHERMASTER
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Description
Qty.
Dia.
Long Leg Pole, steel
(w/ red marking)
4
19mm
Short Leg Pole, steel
4
19mm
Curved Ridge Pole, steel
(w/ red marking)
2
19mm
Curved Ridge Pole, steel
2
19mm
Awning Pole, black,
fiberglass, metal tips
1
6.3mm 5010000543
Door Pole, long, thin, black,
fiberglass, rubber tips
1
6.3mm 5010000543
Vert. Door Pole, short, black,
fiberglass, rubber tips
1
6.3mm 5010000543
Self-Rolling Window Spring Descriptions
Color Code Description
Qty.
Red
1
Green
3
Orange
2
CAUTION: "Springs" may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door
facing the desired direction. Unzip doors. (Fig. 1)
Door
2. Pull four corners of tent taut, then secure by
driving stakes through web loops at an angle for
better anchoring. (Fig. 2)
3. Assemble four, steel, shock-corded, curved
Ridge Poles. Insert Ridge Poles (with red
marking) into center sleeves on top of tent
with the red trim (Fig. 3). Insert the remain-
ing curved Ridge Poles into the other two
sleeves on top of tent.
4. Assemble eight, steel, shock-corded, Leg
Poles. Push down on steel button on tapered
end and insert into end with four holes.
NOTE: Make sure steel button locks into
third hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
(with red marking) into the
ends of the Ridge Pole
(with red marking). Insert
curved end of remaining
short Leg Poles into the
ends of the remaining
Ridge Poles. (Fig. 5 & 6)
Fig. 5
.
Pole
Pole
Repair Kit Replacement Kit
N/A
5010000608
N/A
5010000610
N/A
5010000607
N/A
5010000609
5010000545
5010000545
5010000545
Length
Replacement Part No.
360mm
5010000624
610mm
5010000627
670mm
5010000628
Fig. 1
Fig. 2
Fig. 3
Ridge Pole
with Red
Marking
Sleeve
with Red
Trim
Button in third hole
Fig. 4
Ridge Pole with
Red Marking
Sleeve
Curved End of
with Red
Long Leg Pole
Trim
6 SCREENED TENT
®
Curved Ridge Poles with Red Markings in center sleeves
6. Rotate all eight Leg Poles upright and insert pin on
each web loop at the side locations as shown.
(Fig. 7 & 7A)
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg
Poles to attach. (Fig. 8)
8. To stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
• Pull up on top Leg Pole section until
tent is taut;
• Twist the lower Leg Pole clockwise
until the button locks into the center
or lowest hole;
• Repeat on remaining Leg Poles.
9. Insert plastic stakes through web straps located
on both sides of tent, then drive in to secure.
(Fig. 10)
NOTE: It may be necessary to remove metal
stakes through web straps at side of tent and
screen room, pull tent taut, and drive in stakes
to secure.
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Vertical Pole
Sleeve
Door Hinge
Fig. 14
Top
Top
Door
Door
Pole
Pole
Hinge
Hinge
Sleeve
Sleeve
(continued on other side)
MODEL 2000001588
Fig. 6
7A
Pin
Fig. 7
Fig. 8
Fig. 9
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Fig. 10
Fig. 12
Fig. 13
Fig. 15
Fig. 16

Advertisement

loading

Summary of Contents for Coleman ELITE WEATHERMASTER 2000001588

  • Page 1 ELITE WEATHERMASTER 6 SCREENED TENT ® MODEL 2000001588 Before you begin Fig. 6 Curved Ridge Poles with Red Markings in center sleeves Read all instructions before set up. • Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.
  • Page 2 Fig. 25 NOTE: Repeat steps above for inserting the color matching “spring(s)” into sleeve(s) for the rest of The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219 Push in at top to the windows. 1-800-835-3278 • www.coleman.com engage “spring(s)”...

This manual is also suitable for:

Elite weathermaster 6