Coleman WEATHERMASTER 2000001598 Manual

WEATHERMASTER
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Description Qty. Dia.
Long Leg Pole, steel
(w/ red marking) 2 19mm
Short Leg Pole, steel 4 19mm
Curved Ridge Pole, steel
(w/ red marking) 1 19mm
Curved Ridge Pole, steel 2 19mm
Side Window Pole, black,
fiberglass, metal tips 2 8.5mm 5010000541
Door Pole, long, thin ,black,
fiberglass, rubber tips 1 6.3mm 5010000543
Vert. Door Pole, short, black,
fiberglass, rubber tips 1 6.3mm 5010000543
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
2. Pull four corners of tent taut, then secure by
driving stakes through web loops at an angle
for better anchoring. (Fig. 2)
3. Assemble three, steel, shock-corded,
curved Ridge Poles. Insert Ridge Pole
(with red marking) into center sleeve
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
4. Assemble six, steel, shock-corded, Leg Poles. Push down
on steel button on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
(with red marking) into
the ends of the Ridge
Pole (with red marking).
Insert curved end of
remaining short Leg
Poles into the ends of
the remaining Ridge
Fig. 5
Poles. (Fig. 5 & 6)
Ridge Pole with
Red Marking in
center sleeve
.
Pole Pole
Repair Kit Replacement Kit
N/A 5010000614
N/A 5010000623
N/A 5010000613
N/A 5010000615
5010000547
5010000545
5010000545
Fig. 1
Door
Fig. 2
Fig. 3
Ridge Pole
with Red
Marking
Sleeve
with Red
Trim
Button in third hole
Fig. 4
Ridge Pole with
Red Marking
Sleeve
Curved End of
with Red
Long Leg Pole
Trim
Fig. 6
10 TENT
®
6. Rotate all six Leg Poles upright and insert
pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)
7B
Metal Tip
Hole in
Sleeve
Leg Pole
Window Pole
7C
6. Assemble the two, shock-corded, black Window Poles, then
insert one into sleeve located at each end of tent. (Fig. 7 & 7B)
7. Insert tapered metal tip on Window Pole into Leg Pole.
NOTE: It may be necessary to gently rotate Leg Pole so the
hole will line up with the Window Pole.
8. Go to opposite end of each window pole and gradually apply
pressure to the pole forming an arch. Insert the pin into the
leg pole end at the corners of tent. (Fig. 7 & 7C)
9. Locate the plastic hooks at sides and corners of tent, then
snap onto Leg Poles to attach. (Fig. 8)
10. Locate web strap
with plastic hook on
the sides of each
end panel Window
Vent, then snap onto
the corner Leg Pole.
(Fig. 9)
11. To stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.10);
• Pull up on top Leg Pole section until
tent is taut;
• Twist the lower Leg Pole clockwise
until the button locks into the center
or lowest hole;
• Repeat on remaining Leg Poles.
12. Insert plastic stakes through web straps
located on both sides of tent, then drive
in to secure. (Fig. 11)
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter
black pole with plastic cap tips); then
insert through zippered sleeve on side
of door and into hinge. (Fig. 12)
(continued on other side)
MODEL 2000001598
7A
Pin
Fig. 7
Fig. 8 Fig. 9
Corner
Leg
Pole
Window Vent
Web Tent Strap
Fig. 10
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Fig. 11
Fig. 12
Sleeve
Hinge