Advertisement
Quick Links
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTALLATION OF LYTECASTER
NOTE: Use this Instruction Sheet only when Lytecaster Trim is being installed in the 1100 series Frame-In Kits. If not, disregard
this Instruction Sheet. It is recommended you maintain a copy of the following instructions for reference.
Fig. A
FRAME-IN
WARNING: BEFORE INSTALLING REFLECTOR TO FRAME-IN KIT, READ MARKINGS IN REFLECTOR TRIM AND IN SOCKET CUP
OF FRAME-IN KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAMING
KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITH INSULATED CEILING. IF A NON I.C. TYPE FRAME-IN KIT IS USED,
DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN
SUCH A MANNER TO ENTRAP HEAT. FOR I.C. TYPE INSTALLATION ONLY: ASSEMBLE SOCKET CUP IN UPPER SLOT POSITION
FOR REFLECTOR TRIMS WITH DUAL SLOT POSITIONS.
1. FRAME-IN (Fig. A)
See Frame-In Kit Instruction Sheet for installation procedure.
2. ROTATE ROTO-CLIPS (Fig. B)
Rotate (4) ROTO-CLIPS so that the SHORT LEGS extend inwardly
toward the center opening.
Note: The SHORT LEG of the ROTO-CLIP has no return on top.
3. SNAP-ON (Fig. C)
Insert SOCKET CUP in neck of REFLECTOR. Make sure SPRINGS
of SOCKET CUP snap into SLOTS of REFLECTOR. There are upper
and LOWER SLOTS in the REFLECTOR. Set the cup as indicated
below:
Type I.C. Frame-In Kit: Use upper slot for all lamps (use socket
extender Cat. No. 1968 for PAR30).
13W DTT Frame-In Kit: Use lower slot.
Non-Type I.C.:
Use lower slot for 100W A19, upper slot
for 150W PAR38.
4. PUSH UP (Fig. D)
Push REFLECTOR TRIM straight up until it is tight against ceiling.
If multiple REFLECTOR TRIMS are used in same installation make
sure CROSS BLADE BAFFLES are in line with each other. (Fig. F)
To remove CROSS BLADE BAFFLE pull BAFFLE out of REFLECTOR
TRIM. To replace BAFFLE match RIB on side of BAFFLE with SLOT
in REFLECTOR TRIM and push BAFFLE into REFLECTOR TRIM
until CLIP engages in BAFFLE GROOVE. (Fig. G)
Note
: To remove REFLECTOR TRIM twist REFLECTOR TRIM
counterclockwise while pulling downward. When using 1104
Series Frame-In Kits, first remove CROSS BLADE BAFFLE by
pulling downwards, then squeeze REFLECTOR SPRINGS from
inside until the TRIM disengages. To retrieve SOCKET CUP,
pull on one of the SOCKET SPRING LEGS to disengage. (Fig. H)
®
REFLECTOR TRIM IN THE 1100 SERIES FRAME-IN KIT
Fig. B
ROTATE CLIPS
(if Frame-In Kit is so equipped)
INSTRUCTION SHEET NO.
IS:1132
A0997 Page 1 of 1
Fig. C
SNAP-ON
ROTO-CLIP
POSITION
SHORT LEG
Fig. E
REFLECTOR TRIM
•
CROSS BLADE BAFFLES
Fig. F
SOCKET SPRING
LEG
REFLECTOR
SPRING
Fig. H
®
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
Fig. D
PUSH-UP
LONG LEG
(with return)
ROTO-CLIP (4)
RIB
CROSS BLADE
CLIP
BAFFLE
Fig. G
GROOVE
SOCKET
CUP
Advertisement
