Summary of Contents for Hanna Instruments HI 98701
Page 1
Instruction Manual HI 98701 • HI 98801 HI 98704 • HI 98804 Printing and Logging K-J-T Thermocouple Thermometers w w w . h a n n a i n s t . c o m...
Dear Customer, PRELIMINARY EXAMINATION ® Thank you for choosing a HANNA instruments product. Please read this instruction manual carefully before using the instru- Remove the instrument from the packing material and examine it ment. carefully to make sure that no damage has occurred during shipping.
GENERAL DESCRIPTION FUNCTIONAL DESCRIPTION This series of HANNA instruments ® portable thermocouple thermom- eters with built-in printer and microprocessor technology, provides accurate temperature measurements and data record. The meters can support K, J or T thermocouple probes, one for models HI 98701 and HI 98801, up to four for HI 98704 and HI 98804.
SPECIFICATIONS INITIAL PREPARATION Each meter is supplied complete with batteries. Remove the back Range (*) -200.0 to 999.9 °C ; 1000 to 1370 °C cover, unwrap the batteries and install them while paying attention -300.0 to 999.9 °F ; 1000 to 2500 °F to the polarity.
PASSWORD PROTECTION SETUP MODE Setting of the GLP parameters (calibration alarm time-out, instrument ID code, time and date) can be password protected. If password is set Setup can be used to view data regarding instrument status (e.g. to a value different from 0000 (factory setting), the user will be asked battery charge) or GLP data (e.g.
Page 6
cod. 33: Year Code Valid values Default cod. 40: Auto OFF 10 Show GLP data cod. 41: Battery test 11 Calibration alarm time-out On(enabled); Off(disabled) On cod. 50: Baud rate 20 Instrument ID code 0000÷9999 0000 cod. 60: Release code 30 Current time hh:mm 00:00...
Page 7
the last printed sample number. It is then possible to select TO RESET PRINTING SAMPLE NUMBER another sample. (HI98701 and HI98704 only) • Press the ALT and FNC keys to return to setup mode. This feature resets the print on demand sample number to 001. Viewing logged data •...
TEMPERATURE CALIBRATION PROCEDURE TAKING TEMPERATURE MEASUREMENTS (for technical personnel only) To prepare the instrument for use, choose the most appropriate temperature probe for your application (see "Accessories" section) and The meter is factory calibrated. However, as a general rule, it is connect it to the instrument.
THERMOCOUPLE CALIBRATION HI 98801 - HI 98804 1. With a mV simulator, input 0.000 mV at channel 1 of the meter. PRINTING / LOGGING FUNCTIONS 2. Ensure the meter is not displaying the cold junction temperature and press ALT, CFM and PAPER simultaneously while the meter is Two different modes to print / log data are available: not printing nor logging to enter calibration mode.
Page 10
logged reading will appear briefly on the LCD. To reactivate the the value will be stored in the lot 00 (log on demand data area). If LCD press ON/OFF. the print function is enabled, a printout is also produced providing the following information: TO STOP LOGGING a - Date...
TO RETRIEVE LOGGED DATA TO STOP PRINTING Logged data can be viewed on LCD or printed. To view or print logged In order to stop the recording mode, press data see "TO SCAN LOGGED DATA" in the "SETUP MODE" paragraph. ALT and LOG keys (press ON/OFF first, if meter is in sleep mode).
® compatible application software offered and LIGHT keys. The LCD backlight can be disabled in order to save by HANNA instruments ® power, and it is automatically disabled when a low battery level is HI 92000 allows you to use the powerful capabilities of most spread detected.
PRINTER MAINTENANCE MEMORY ORGANIZATION HI 98801 - HI 98804 only TO CHANGE THE INK CARTRIDGE When printouts become faint, it might be necessary to change the ink Logged data are stored in the internal EEPROM and are retained even cartridge. Contact your Hanna authorized center. if batteries and external power are disconnected.
BATTERY REPLACEMENT K-TYPE THERMOCOUPLE PROBES When the batteries are inserted and no power adapter is connected, WITH DETACHABLE HANDLE & MINI-CONNECTOR the meter can recognize different batteries charge levels. (to be plugged into HI 766HD probe handle) 1. Fully charged batteries. The backlight and printer can be enabled.
Page 15
HI 766PE1 General use probe, max 900°C/1650°F HI 766B1 90° surface probe, max 450°C/840°F 155mm 6.1" 30mm 0.12" 1.2" 300mm 11.8" HI 766B2 Surface probe, max 900°C/1650°F HI 766PE2 General use probe, max 900°C/1650°F 200mm 0.3" 7.8" 130mm 0.20" 5.1" HI 766B3 Small surface probe with insulated shaft, max 200°C/390°F HI 766HD Rugged thermocouple probe handle with 1m (3.3' ) cable fitted with a mini-connector...
HI 766F1 Flexible probe without handle, max 480°C/900°F incurred. If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization number from the Customer Service department and then send it with shipping costs prepaid.