Yamaha RX-V473 Owner's Manual page 31

1 2 3 4 5 6 7 8 9 10
Automatic speaker setup
CODE SET CODE SET
SOURCE SOURCE RECEIVER RECEIVER
HDMI HDMI
1 1 2 2 3 3 4 4
AV AV
1 1 2 2 3 3 4 4
5 5 6 6 AUDIO AUDIO A A
V-AUX V-AUX USB USB NET NET B B
ZONE ZONE
TUNER TUNER
FM FM AM AM
PRESET PRESET TUNING TUNING
INFO INFO MEMORY MEMORY
SUR. DECODE SUR. DECODE STRAIGHT STRAIGHT
MOVIE MOVIE MUSIC MUSIC
ENHANCER ENHANCER DIRECT DIRECT
SLEEP SLEEP
SCENE SCENE
BD BD
TV TV NET NET RADIO RADIO
DVD DVD
SETUP
SETUP OPTION OPTION
Cursor keys
ENTER VOLUME VOLUME
ENTER
RETURN
DISPLAY DISPLAY
RETURN
TOP TOP
POP-UP POP-UP
MUTE MUTE
MENU MENU MENU MENU
MODE MODE
1 1 2 2 3 3 4 4
5 5 6 6 7 7 8 8
9 9 0 0 10 10 ENT ENT
TV TV
INPUT INPUT
TV VOL TV VOL TV CH TV CH
MUTE MUTE
• To cancel the operation, disconnect the YPAO microphone, or use the
cursor keys to select "Exit" and press ENTER, before starting the
measurement.
• Do not stand between the speakers and the YPAO microphone during the
measurement process (about 3 minutes).
• Move to the corner of the room or leave the room.
5
To start the measurement, use the cursor keys to
select "Start" and press SETUP.
The measurement will start in 10 seconds. Press ENTER to
start the measurement immediately.
• To stop the measurement temporarily, press RETURN and follow the
procedure in "Error messages" (p.32).
The following screen appears on the TV when the
measurement finishes.
A u t o S e t u p
M e a s u r e m e n t
F i n i s h e d
S t a r t
Result
E x i t
3 / 2 / 0.1 ch
3.0 / 10.5 m
-3.0 / +10.0 dB
1
The number of speakers (front side/rear
side/subwoofer)
2
Speaker distance (nearest/farthest)
3
Adjustment range of speaker output level
4
Warning message (if available)
• If any error message (such as E-1) or warning message (such as W-1)
appears, see "Error messages" (p.32) or "Warning messages" (p.33).
• A speaker with a problem is indicated by blinking of the speaker indicators in
the front display.
• If multiple warnings are given (when operating with the front display), use
the cursor keys (q/w) to check the other warning messages.
6
To save the measurement results, use the cursor
keys (e/r) to select "SAVE" and press ENTER.
A u t o S e t u p
S t a r t
E x i t
The adjusted speaker settings are applied.
• To finish the measurement without saving the result, select "CANCEL".
7
Disconnect the YPAO microphone from the unit.
1
2
This completes optimization of the speaker settings.
3
Caution
4
• The YPAO microphone is sensitive to heat, so should not be placed anywhere
where it could be exposed to direct sunlight or high temperatures (such as on
top of AV equipment).
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO)
M e a s u r e m e n t
F i n i s h e d
Result
S A V E
3 / 2 / 0.1 ch
3.0 / 10.5 m
-3.0 / +10.0 dB
31
En