Keep all detergents in a safe place out of children’s Under no circumstances should you attempt to repair the reach. machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Zanussi Service Centre. Always insist on genuine Zanussi spare parts.
Table of Contents For the User For the Installer Important Safety Information Installation Instructions Description of the Appliance Technical Specifications Unpacking The Control Panel Positioning Operating sequence Water inlet Water drainage 17-18 Before the first use Levelling Load the laundry Special conditions Measure out the detergent Electrical connections...
The Control Panel F L S - 5 7 1 C 10 11 12 13 14 1 Programme Guide 4 Cold Wash button Pressing this button when starting any program it will be 2 ON/OFF LAMP run through with cold water. All other features of the program as intensity and duration remain unchanged.
Operating Sequence Before your first wash, we recommend that you run a cotton cycle at 60°C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine.
4. Select the required programme Turn the programme selector dial CLOCKWISE to the required programme. P0215 5. Start the machine Before starting up the machine check that: the appliance is plugged in the water supply tap is turned on the door and the detergent dispenser drawer are closed.
Washing Programmes Programmes for cotton and linen Maximum load 5 kg Program. Compartments Possible dial Program Temperature ˚C Degree of soil Description to use options position Prewash at 40 ˚C Whites with Wash at 90˚C 90° Heavy soiled prewash 4 rinses Spin at 500 rpm Whites Wash at 90˚C...
Page 9
Washing Programmes Programmes for synthetics, delicates and wool Maximum load 2 kg (wool maximum load 1 kg) Program. Compartments Possible dial Program Temperature ˚C Degree of soil Description to use options position Prewash at 40 ˚C Mixed Wash at 60˚C 60°...
Washing Hints Do NOT overload the machine. Weigh the laundry the Some stains such as fruit, wine, grass, rust etc. are first few times you use the appliance. difficult to remove and should be treated before washing with specific products, which can be found The average weights of the most common items are in most household shops.
Wash Care Symbols Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct programme on your washing machine.
Maintenance and Cleaning Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply Descaling The water we normally use contains lime. It is a good idea to periodically use a water softening powder in the machine.
Cleaning the filter The water drain filter A clean filter is important for the correct functioning of the machine, and should therefore be cleaned after every washing programme. Open the filter door and place a container underneath to catch any spillage. If the filter is blocked and the machine is unable to drain you will need to drain the water manually from the machine at this stage.
Something Not Working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your Local service Force Centre, please carry out the checks listed below. Symptom Possible causes The machine does not start The door has not been closed.
Installation Instructions It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
Unpacking Before starting the machine up, the transport security bolts must be removed as follows: You are advised to keep all the packaging for re-use in case the appliance has to be transported again. Unscrew and remove the three rear transit bolts (using a spanner).
Positioning Your new Zanussi washing machine has been designed to be permanently plumbed in to you home’s water supply and drainage system. However, if this is not possible, it may be connected to suitable existing taps, with the drain hose discharging into the sink.
If the machine is permanently plumbed in, hook the end of the hose into a standpipe installed for the purpose. The standpipe must have an internal diameter of at least 40mm in order that there is an air gap between the drain hose and the standpipe.
The cover/carrier is indicated by the coloured insert at the base of the plug. A replacement cover/carrier must be obtained from your local Zanussi Service Centre, whose address is listed in the Customer Care Booklet which accompanies your instruction manual...