1. Manuals
  2. Brands
  3. Canon Manuals
  4. Printer
  5. Satera LBP5610
  6. User manual

Canon Satera LBP5610 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Laser Beam Printer
User's Guide
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Canon Satera LBP5610

Summary of Contents for Canon Satera LBP5610

  • Page 1 Laser Beam Printer User's Guide User's Guide...

  • Page 2: Table Of Contents

    Contents Turning the Printer ON/OFF (For 5910/5910F) ......3 Turning the Printer ON ..........3 Turning the Printer OFF .
  • Page 3 Staple Jams (Only for LBP5910F) ........92 Precautions on Clearing Staple Jams .

  • Page 4: Turning The Printer On/Off (For 5910/5910F)

    Turning the Printer ON/OFF (For 5910/5910F) The power switch to turn the printer ON or OFF is located on the right side of the printer. Be sure to observe the following instructions in order to prevent unexpected problems. Turning the Printer ON In order to use this printer, you should press "...

  • Page 5: Turning The Printer Off

    The indicators of the control panel and the display come on, and the printer initiates a self-diagnostic test on the printer unit and optional accessories. If no abnormality is found during the self-diagnostic test, the indicator and the indicator, and the selected paper source display indicator comes on, <...

  • Page 6: When Not Using A Hard Disk

    When Not Using a Hard Disk When you are not using a hard disk, turn the printer OFF using the following procedure. Make sure that indicator is off. Press " " of the power switch on the printer.

  • Page 7: When Using A Hard Disk (Only When A Hard Disk Is Installed)

    When Using a Hard Disk (Only When a Hard Disk is Installed) When using the optional hard disk, turn the printer OFF using the following procedure. IMPORTANT If you perform a shutdown when any job of which you stopped the operation or of •...
  • Page 8 Confirm the message. When the printer is ready to be turned OFF after the process for it is performed, the message < > appears. When the message < > appears, press " " of the power switch on the printer.

  • Page 9: Turning The Printer On/Off (For Lbp5610)

    Turning the Printer ON/OFF (For LBP5610) The power switch to turn the printer ON or OFF is located on the right side of the printer. Be sure to observe the following instructions in order to prevent unexpected problems. Turning the Printer ON In order to use this printer, you should press "...

  • Page 10: Turning The Printer Off

    The indicators come on, and the printer initiates a self-diagnostic test on the printer unit and optional accessories. If no abnormality is found during the self-diagnostic test, the indicator (blue) comes on, and the printer is ready to print. Turning the Printer OFF Turn the printer OFF using the following procedure.

  • Page 11: Online And Offline (Only For Lbp5910/5910F)

    Online and Offline (Only for LBP5910/5910F) "Online" is the status that the printer receives data from the computer and is possible to print, while "Offline" is the status that the connection with the computer is cut off and be impossible to receive data. To perform the setting for each menu using the control panel, switch the printer status as follows: : The status that can go into a menu.

  • Page 12: Placing The Printer Offline

    NOTE When the printer is switching to the sleep mode, the indicator is off and only the indicator comes on even if the printer is online. If the printer receives data in the sleep mode, the sleep mode is released, the indicator comes on, and the printer is ready to print.

  • Page 13: Paper Requirements

    Paper Requirements To ensure optimum performance, use only paper that falls within the specifications in the following lists. Using inappropriate paper may result in deterioration in print quality or paper jams. Usable Paper The following shows the paper sizes that can be used with this printer. The " " mark indicates that the paper is available for the 1-sided printing and automatic 2-sided printing;...
  • Page 14 Paper Source Multi- Paper Size Cassette 2 Cassette 3 Cassette 4 purpose Cassette 1 (Optional) (Optional) (Optional) Tray 12 x 18* SRA3* Custom Paper Size Long Size Paper* Postcard* 100.0 mm x 148.0 mm Reply Postcard* 148.0 mm x 200.0 mm 4 on 1 Postcard* 200.0 mm x 296.0 mm Envelope*...

  • Page 15: Paper Type For Lbp5910/5910F

    Paper Type for LBP5910/5910F Paper Source Multi- Paper Type Cassette 2 Cassette 3 Cassette 4 purpose Cassette 1 (Optional) (Optional) (Optional) Tray Plain paper* (64 - 105 g/m Heavy paper (106 - 220 g/m Coated paper Labels Postcard Envelopes * 100% recycled paper (64 - 105 g/m ) can be used as plain paper.

  • Page 16: Paper Type For Lbp5610

    Paper Source Multi- Paper Size Cassette 2 Cassette 3 Cassette 4 purpose Cassette 1 (Optional) (Optional) (Optional) Tray Long Size Paper* Envelope* Envelope DL 110.0 mm x 220.0 mm Envelope COM10 104.9 mm x 241.3 mm Envelope C5 162.0 mm x 229.0 mm Envelope Monarch 98.5 mm x 190.5 mm...
  • Page 17 Paper Source Multi- Paper Type Cassette 2 Cassette 3 Cassette 4 purpose Cassette 1 (Optional) (Optional) (Optional) Tray Labels Envelopes * 100% recycled paper (64 - 105 g/m ) can be used as plain paper. ■ Plain Paper for LBP5910/5910F This printer can print Plain paper of the standard paper sizes (A3, B4, A4, B5, A5, SRA3, 12 x 18, Ledger (11X17), Legal, Letter, Executive, Postcard, Reply postcard, 4 on 1 postcard), Custom paper size, and Long size paper.

  • Page 18: Coated Paper

    This printer can print A3 and A4 size coated paper. Load coated paper in the multi-purpose tray. IMPORTANT Use "A3 size coated paper that Canon recommends", and "A4 size coated paper that Canon recommends". ■ Label This printer can print A4 size labels. Labels can be loaded in the paper cassettes and multi-purpose tray.
  • Page 19 YOUGATA No.2 (Envelope K-201G for LBP that (105 mm x 235 mm) (114 mm x 162 mm) Canon recommends) * You cannot use envelopes at sizes of YOUGATA No.4 and YOUGATA No.2 that have a flap on the short edge.
  • Page 20 IMPORTANT Do not use the following types of envelopes. Using inappropriate envelopes may result in • paper jams that are difficult to clear or may result in damage to the printer. - Envelopes with fasteners or snaps - Envelopes with address windows - Envelopes with adhesive on the surface - Wrinkled or creased envelopes - Poorly manufactured envelopes in which the glued parts are uneven...
  • Page 21 NOTE When printing envelopes, they may be creased. ■ Envelope for LBP5610 The envelopes that can be used with this printer are Envelope DL, Envelope COM10, Envelope C5, Envelope Monarch, and Envelope B5, and the one that have the following structures only.

  • Page 22: Printable Area

    When loading DL, COM10, C5 or Monarch, load them so that the flap is toward the left of • the printer when viewed from the front. When loading envelopes at size of Envelope B5, close the flaps and load them so that •...
  • Page 23 NOTE If you are using LBP5610, and the paper is 315 mm wide or more, the right and left margins are extended according to the width as follows. Paper Width Margin 315 mm 5 mm 316 mm 5.5 mm 317 mm 6 mm 318 mm 6.5 mm...

  • Page 24: Unusable Paper

    100 mm 200 mm 5 mm 5 mm 148 mm 148 mm 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm ■ Envelopes You cannot print on any area within 10 mm of the edges of an envelope. You may have to change the printable area before printing, depending on the application you use.
  • Page 25 - Irregularly-shaped paper - Wet or moist paper - Torn or damaged paper - Rough, extremely smooth, or glossy paper - Paper with binding holes or perforations - Curled or creased paper - Specially coated paper (coated paper for ink jet printers, etc.) - Labels with backing sheet that is easily peeled off - Paper that has already been printed by a copy machine or another laser printer (The reverse side of the paper is also unusable.).

  • Page 26: Paper Capacity Of Paper Source

    Approx. 40 (Only for LBP5910/5910F) sheets 4 on 1 Postcard Approx. 40 (Only for LBP5910/5910F) sheets 4 on 1 Postcard Approx. 50 Recommended by Canon sheets Approx. 10 Envelopes sheets Paper Capacity of the Output Tray Output Tray* Paper Type LBP5910/5610...
  • Page 27 Approx. 50 sheets 5910F) 4 on 1 Postcard Recommended by Approx. 200 sheets Approx. 100 sheets Canon Envelopes Approx. 20 sheets Approx. 20 sheets* Actual paper capacity varies depending on the installation environment or paper type. Indicates the number for when A4, B5, A5, Letter, or Executive size paper is loaded. For the other sizes, the number varies as follows.

  • Page 28: Loading Paper In The Paper Cassette

    When Loading Paper in Cassette 2, 3, or 4* : p. 36 Only when the optional paper feeders are installed A4 size label that Canon recommends IMPORTANT For more details on the usable paper, see "Usable Paper," on p. 12.
  • Page 29 After lifting the paper cassette up a little b, pull it out while supporting it with other hand as shown in the figure c. CAUTION Be sure to take the paper cassette out of the printer before loading paper. If paper is loaded while the paper cassette is partially pulled out, the paper cassette may drop or the printer may become damaged resulting in personal injury.
  • Page 30 Paper Size Paper Guides Executive EXEC ● Adjust the length of the paper cassette according to the size of the paper to be loaded. When loading paper in landscape orientation, such as when loading A4, B5, A5, Letter, or Executive size paper, shorten the paper cassette. When loading paper in portrait orientation, such as when loading A3, B4, Ledger (11X17), or Legal size paper, extend the paper cassette.
  • Page 31 ● While holding the lock release lever of the side paper guide , slide the guide to the mark for the size of the paper to be loaded The side paper guides move together. Top View Top View Align this part with the paper size to be loaded...

  • Page 32: Paper Guide

    Load the paper stack so that the rear edge is aligned with the paper guide. CAUTION When loading paper, take care not to cut your hands with the edges of the paper. IMPORTANT Be sure to check if the paper guide is at the position of the size of the loaded paper. •...
  • Page 33 Press down the paper stack so that it is loaded under the hooks on the side paper guides (A). Make sure that there is sufficient space between the hooks and paper stack. If there is no sufficient space, slightly reduce the amount of paper. IMPORTANT Up to approximately 250 sheets of plain paper (64 g/m ) or approximately 50...
  • Page 34 Attach the label for the size of the loaded paper to the paper size indicator, and insert the guide into the paper size slot at the front of the paper cassette. Hold the tab (B) of the paper size setting switch (A) , and align the paper size with the triangular mark of the paper size setting switch...
  • Page 35 The default is "A4". IMPORTANT Make sure that the size of the loaded paper matches that of the paper size setting switch before setting the paper cassette in the printer. If the size indicated by the paper size setting switch does not match, this may result in printer malfunction. Set the paper cassette in the printer.
  • Page 36 After lifting the front of the paper cassette up a little b, push the paper cassette into the printer firmly until the front side of the paper cassette is flush with the front surface of the printer c. CAUTION When setting the paper cassette to the paper feeder, be careful not to catch your fingers.

  • Page 37: When Loading Standard Size Paper In Cassette 2, 3, Or 4

    When Loading Standard Size Paper in Cassette 2, 3, or 4 Pull the paper cassette out. Pull the paper cassette out until it stops a.
  • Page 38 After lifting the paper cassette up a little b, pull it out while supporting the cassette with your left hand until the handle (A) on the right side of the paper cassette appears completely c. While holding the paper cassette with both hands, pull it out completely d as shown in the figure.
  • Page 39 CAUTION Be sure to take the paper cassette out of the paper feeder before loading paper. If paper is loaded while the paper cassette is partially pulled out, the paper cassette may drop or the printer may become damaged resulting in personal injury.
  • Page 40 ● While holding the lock release lever of the side paper guide , slide the guide to the mark for the size of the paper to be loaded The side paper guides move together. When loading labels, fan them in small batches and align the edges.
  • Page 41 Load the paper stack so that the rear edge is aligned with the paper guide. CAUTION When loading paper, take care not to cut your hands with the edges of the paper. IMPORTANT Be sure to check if the paper guide is at the position of the size of the loaded paper. •...
  • Page 42 Press down the paper stack so that it is loaded under the hooks on the side paper guides (A). Make sure that there is sufficient space between the hooks and paper stack. If there is no sufficient space, slightly reduce the amount of paper. IMPORTANT Up to approximately 550 sheets of plain paper (64 g/m ) or approximately 50...
  • Page 43 Attach the label for the size of the loaded paper to the paper size indicator, and insert the guide into the paper size slot at the front of the paper cassette. Hold the tab (B) of the paper size setting switch (A) , and align the paper size with the triangular mark of the paper size setting switch...
  • Page 44 The default is "A3". CUSTOM IMPORTANT Make sure that the size of the loaded paper matches that of the paper size setting switch before setting the paper cassette in the printer. If the size indicated by the paper size setting switch does not match, this may result in printer malfunction.
  • Page 45 Set the paper cassette in the paper feeder. While holding the paper cassette with both hands, push it to the position shown in the figure a. Then, hold the front of the paper cassette with your right hand and push it until it stops b.

  • Page 46: When Loading Custom Size Paper (Non-Standard Size Paper) In Cassette 2, 3, Or 4

    After lifting the front of the paper cassette up a little c, push the paper cassette into the printer firmly until the front side of the paper cassette is flush with the front surface of the paper feeder d. CAUTION When setting the paper cassette to the paper feeder, be careful not to catch your fingers.
  • Page 47 When changing orientation of custom paper size to be loaded frequently in case of • LBP5910/5910F, it is convenient to set < > to < >. It is not necessary to change the setting for < > each time to change orientation of the paper to be loaded. Observe the following guidelines when setting to <...
  • Page 48 After lifting the paper cassette up a little b , pull it out while supporting the cassette with your left hand until the handle (A) on the right side of the paper cassette appears completely c . While holding the paper cassette with both hands, pull it out completely d as shown in the figure.
  • Page 49 IMPORTANT The paper cassette cannot be pulled out horizontally. If trying to pull it out forcefully, • this may result in damage to the paper cassette. Because the paper cassette is heavy, hold it with your both hands securely. • Place the removed paper cassette on an even and stable surface.
  • Page 50 Slide the paper guides. ● While holding the lock release lever of the rear paper guide , slide the guide to the mark for the size of the paper to be loaded ● While holding the lock release lever of the side paper guide , slide the guide to the mark for the size of the paper to be loaded The side paper guides move together.
  • Page 51 IMPORTANT Be sure to align the paper guides with the width of the paper. If the paper guides are too loose or too tight, this may result in misfeeds or paper jams. Press down the paper stack so that it is loaded under the hooks on the side paper guides (A).
  • Page 52 Hold the tab (B) of the paper size setting switch (A) , and align the triangular mark of the paper size setting switch with "CUSTOM" The default is "A3". CUSTOM IMPORTANT Make sure that paper size setting switch matches "CUSTOM" before setting the paper cassette in the printer.
  • Page 53 Set the paper cassette in the paper feeder. While holding the paper cassette with both hands, push it to the position shown in the figure a . Then, hold the front of the paper cassette with your right hand and push it until it stops b .
  • Page 54 After lifting the front of the paper cassette up a little c , push the paper cassette into the printer firmly until the front side of the paper cassette is flush with the front surface of the paper feeder d . CAUTION When setting the paper cassette to the paper feeder, be careful not to catch your fingers.

  • Page 55: Loading Paper In The Multi-Purpose Tray

    Reply Postcard (148.0 mm x 200.0 mm) p. 60 5910F) 4 on 1 Postcard (200.0 mm x 296.0 mm) A3 size coated paper that Canon recommends A4 size coated paper that Canon recommends A4 size label that Canon recommends Envelope K-201G for LBP that Canon recommends...

  • Page 56: When Loading Paper (Other Than Postcards And Envelopes)

    IMPORTANT For more details on the usable paper, see "Usable Paper," on p. 12. When Loading Paper (Other than Postcards and Envelopes) Use the following procedure to load plain paper, heavy paper, coated paper or label in the multi-purpose tray. Open the multi-purpose tray.
  • Page 57 When loading the long size paper such as A3, B4, or long size paper, pull the auxiliary tray out a , and open the extension tray b . Spread the paper guides a little wider than the actual paper width.
  • Page 58 Before loading coated paper or labels, fan them in small batches and align the edges. Fan in small batches Align the edges of the stack on a hard and flat surface CAUTION When loading paper, take care not to cut your hands with the edges of the paper.
  • Page 59 CAUTION When loading paper, take care not to cut your hands with the edges of the paper. IMPORTANT When loading long size paper, set one piece at a time to the multi-purpose tray as • shown in the figure. The multi-purpose tray can be loaded with up to the number of sheets listed below. •...
  • Page 60 NOTE If you are using LBP5910/LBP5910F and < > in the • options of the menu is set to < >, load custom paper of its long edges 297.0 mm long or less as follows according to your printer driver before printing.

  • Page 61: When Loading Postcards (Only For Lbp5910/5910F)

    When Loading Postcards (Only for LBP5910/5910F) Postcard, Reply postcard, 4 on 1 postcard and 4 on 1 postcard recommended by Canon can be loaded in the multi-purpose tray. Use the following procedure to load postcard in the multi-purpose tray. IMPORTANT Be sure to use reply postcard that is not be creased.
  • Page 62 Up to approximately 40 sheets of Postcard, Reply postcard, or 4 on 1 postcard or • approximately 50 sheets of 4 on 1 postcard recommended by Canon can be loaded in the multi-purpose tray. Make sure that the postcard stack does not...
  • Page 63 When loading postcard, be sure to load it in portrait orientation so that the printing • side is facing down and the top edge is toward the back of the printer when viewed from the front. When loading Reply postcard, be sure to load them in landscape orientation so •...
  • Page 64 When loading 4 on 1 postcard, be sure to load them in landscape orientation so • that the printing side is facing down and the top edge is toward the left of the printer when viewed from the front. If the postcard is curled, flatten the curls by warping it in the opposite direction •...

  • Page 65: When Loading Envelopes

    YOUGATA No.2 (Envelope K-201G for LBP that (105 mm x 235 mm) (114 mm x 162 mm) Canon recommends) * You cannot use envelopes at sizes of YOUGATA No.4 and YOUGATA No.2 that have a flap on the short edge.
  • Page 66 - LBP5610 Envelope DL Envelope Monarch Envelope B5 (110.0 mm x 220.0 mm) (98.5 mm x 190.5 mm) (176.0 mm x 250.0 mm) Envelope COM10 Envelope C5 (104.9 mm x 241.3 mm) (162.0 mm x 229.0 mm) * You cannot use envelopes at sizes of DL, COM10, Monarch, and C5 that have a flap on the short edge.
  • Page 67 Spread the paper guides a little wider than the actual envelope width. Place the stack of envelopes on a flat surface, flatten them to release any remaining air, and be sure that the edges are pressed tightly. CAUTION When loading paper, take care not to cut your hands with the edges of the paper.
  • Page 68 Loosen any stiff corners of the envelopes and flatten curls as shown in the figure. Align the edges of the envelopes on a flat surface. Gently load the stack of envelopes with the address side facing down and with the flaps closed and on the left side, until it touches the back of the multi-purpose tray as shown in the figure.
  • Page 69 IMPORTANT Up to 10 envelopes can be loaded in the multi-purpose tray. • You cannot print on the reverse side (glued side) of envelopes. • When loading YOUGATA No.4, YOUGATA No.2 (in case of LBP5910/5910F), DL, • COM10, C5 or Monarch (in case of LBP5610), load them so that the flap is toward the right of the printer when viewed from the front.
  • Page 70 When loading envelopes at size of Envelope B5 (in case of LBP5610), close the • flaps and load them so that the bottom of the envelopes is toward the front of the printer when viewed from the front. Align the paper guides with both sides of the stack. IMPORTANT Be sure to align the paper guides with the width of the envelopes.

  • Page 71: Paper Loading Orientation

    Paper Loading Orientation To print letterhead paper or paper printed with a logo, load the paper in the proper orientation as follows. in the table indicates the feeding directions. Loading A4, B5, A5, Letter, or Executive size Loading A3, B4, Ledger (11 x 17), or Legal size paper in landscape orientation paper in portrait orientation Portrait Layout...
  • Page 72 NOTE For details on the loading orientation of envelopes and postcards, see "When Loading • Postcards (Only for LBP5910/5910F)" (p. 60) and "When Loading Envelopes" (p. 64). If you are using LBP5910/LBP5910F and < > or < • > in the options of the menu is set to <...

  • Page 73: Paper Jams

    Paper Jams When a paper jam occurs during printing for some reason, in case of LBP5910/ 5910F warning beep sounds and message < > appears on display, while in case of LBP5610 the following message is displayed on printer status window. ■...
  • Page 74 CAUTION The fixing unit and its surroundings inside the printer are hot during use. Make • sure the fixing unit is completely cool before removing the jammed paper. Touching the fixing unit when it is still hot may result in burns. When removing jammed paper, take care not to allow the toner to come into •...

  • Page 75: Paper Jam Area

    2. Contacting your local authorized Canon dealer for servicing * If < > is specified, the normal printing process (stapling is not performed) is applied to even a job which is specified to be stapled. Do not remove the staple cartridge (A) even if <...
  • Page 76 Message Paper Jam Paper Jam Area Area Mark* LBP5910/5910F LBP5610 No message is Output Area displayed. Inside the front cover <Front Cover> Inside the front cover (Duplex print transport <Duplex Unit> area) Cassette 1 <Cassette 1> Cassette 2 (Only when the paper feeder is <Cassette 2>...

  • Page 77: Procedure For Clearing Paper Jams

    Procedure for Clearing Paper Jams Remove the jammed paper using the following procedure. IMPORTANT The error message may remain if jammed paper is removed without opening the front cover. In this case, open and close the front cover once. NOTE The illustrations of the printer on the left of each step indicate paper jam areas where the operation described in the step is required.
  • Page 78 If using the multi-purpose tray, remove any paper jammed in multi-purpose tray. A B C D E F G IMPORTANT If the jammed paper cannot be removed easily, do not try to remove it forcefully but proceed to Step 3. If using the multi-purpose tray, close it.
  • Page 79 Pull the paper cassette out. Pull the paper cassette out until it stops a . A B C D E F G After lifting the paper cassette up a little b, pull it out while supporting it with other hand as shown in the figure c. IMPORTANT The paper cassette cannot be pulled out horizontally.
  • Page 80 If the paper feeder is installed, pull all the paper cassettes out from the top. Pull the paper cassette out until it stops a. A B C D E F G...
  • Page 81 After lifting the paper cassette up a little b, pull it out while supporting the cassette with your left hand until the handle (A) on the right side of the paper cassette appears completely c. While holding the paper cassette with both hands, pull it out completely d as shown in the figure.
  • Page 82 Remove any jammed paper in the manner of pushing it downward. In case of the printer A B C D E F G In case of the paper feeder IMPORTANT If jammed paper cannot be removed easily, do not try to remove it forcefully but •...

  • Page 83: Open The Front Cover

    Do not touch the paper feed roller (A) and switch (B) on the lower portion of the • printer. This may result in damage to the printer or printer error. Open the front cover. While pressing the lever on the right side of the front cover, open the front cover toward you.
  • Page 84 Pull the fixing unit down toward you. While pressing the green lock release buttons (A) on the left and right side of the fixing unit a, hold the tabs (B) and pull the fixing unit down toward you b as A B C D shown in the figure.
  • Page 85 Remove jammed paper from the front of the fixing unit. A B C D E F G IMPORTANT If jammed paper cannot be removed easily, pull jammed paper out gently and strongly to remove it. If jammed paper still cannot be removed, do not try to remove it forcefully but proceed Step 11.
  • Page 86 While holding the tabs (A), move the fixing unit back to its original position , and then press the tabs on the both sides as shown in the figure A B C D E F G Remove jammed paper in the lower portion of the fixing unit. Turn the dial on the left of the fixing unit in the direction of the arrow to send any jammed paper a as shown in the figure.
  • Page 87 Remove any jammed paper as shown in the figure b. IMPORTANT As the paper may be jammed in the back of the printer, turn the dial sufficiently to send the paper.
  • Page 88 If a paper jam occurs when performing 2-sided printing, open the cover of the duplex print transport guide holding the tab (A) inside the front cover as shown in the figure , and A B C D remove jammed paper E F G...
  • Page 89 Close the front cover. While supporting the front cover a, push and close the front cover with both hands as shown in the figure b. A B C D E F G CAUTION Push the front portion of the front cover to close it as shown in the figure. If closing the front cover by the levers on the both sides, you may catch your fingers, resulting in personal injury.
  • Page 90 Set the paper cassette to the printer. While holding the paper cassette with both hands and insert it until it stops a as shown in the figure. A B C D E F G After lifting the front of the paper cassette up a little b, push the paper cassette into the printer firmly until the front side of the paper cassette is flush with the front surface of the printer c.
  • Page 91 If the paper feeder is installed, set all the paper cassettes to the paper feeder from the top. While holding the paper cassette with both hands, push it to the position shown A B C D in the figure a. Then, hold the front of the paper cassette with your right hand E F G and push it until it stops b.
  • Page 92 After lifting the front of the paper cassette up a little c, push the paper cassette into the printer firmly until the front side of the paper cassette is flush with the front surface of the paper feeder d. CAUTION When setting the paper cassette to the paper feeder, be careful not to catch your fingers.

  • Page 93: Staple Jams (Only For Lbp5910F)

    If a staple jam occurs each time printed paper is stapled, perform either one of the • following methods. 1. Setting < > in < > in the options of the menu to < >* 2. Contacting your local authorized Canon dealer for servicing...

  • Page 94: Procedure For Clearing Staple Jams

    * If LIMIT is specified, the normal printing process (stapling is not performed) is applied to even a job which is specified to be stapled. Do not remove the staple cartridge (A) even if LIMIT is specified. If you print with the staple cartridge removed, this may result in paper jams.
  • Page 95 Open the front cover. While pressing the lever on the right side of the front cover, open the front cover toward you. IMPORTANT Before opening the front cover, make sure that the multi-purpose tray and the paper cassette of the printer are closed.
  • Page 96 Pull the fixing unit down toward you. While pressing the green lock release buttons (A) on the left and right side of the fixing unit a , hold the tabs (B) and pull the fixing unit down toward you b as shown in the figure.
  • Page 97 Holding the tab (A) of the staple cartridge, remove it from the printer. CAUTION The tab of the staple cartridge may be hot. Make sure the tab is completely cool before removing the staple cartridge. Touching the tab when it is still hot may result in burns.
  • Page 98 Remove any jammed or bent staples. Staples have a linear shape before use. Close the cover of the staple cartridge as shown in the figure.
  • Page 99 Holding the tab of the staple cartridge, install it in the printer. Insert the staple cartridge until it clicks. IMPORTANT Insert the staple cartridge straight. If you apply force upward while inserting the staple cartridge, the tab may come off. If the tab comes off, put it back to the original position.
  • Page 100 Close the front cover. While supporting the front cover a , push and close the front cover with both hands as shown in the figure b . CAUTION Push the front portion of the front cover to close it as shown in the figure. If closing the front cover by the levers on the both sides, you may catch your fingers, resulting in personal injury.

  • Page 101: Replacing The Toner Cartridges

    Replacing the Toner Cartridges This section describes how to replace the toner cartridges. When a Message Appears Toner cartridges are consumable products. If getting almost out of toner when using the printer, a message appears on the display in case of LBP5910/5910F , or on the Printer Status Window in case of LBP5610, so follow the directions in the message.
  • Page 102 (See p. 108). NOTE The lifetime of the toner cartridges (Canon Genuine Cartridges) used in this printer are as follows. The numbers of the pages are estimated when printing in the following conditions.

  • Page 103: Precautions On Replacing The Toner Cartridges

    Precautions on Replacing the Toner Cartridges WARNING Do not throw a used toner cartridge into open flames, as this may cause the toner remaining inside the toner cartridge to ignite, resulting in burns or a fire. CAUTION Take care not to allow the toner to come into contact with your hands or clothing, as this will dirty your hands or clothing.
  • Page 104 IMPORTANT The toner cartridges are installed from the back in order of Yellow, Magenta, Cyan, and Black. Yellow Magenta Cyan Black Tilt the lock release lever (A) of the toner cartridge that you want to replace to the position of " ", and release the lock.
  • Page 105 Align the circle mark on the lock release lever with that on the toner cartridge. Top View Align at this part Remove the toner cartridge from the printer. IMPORTANT If the toner cartridge cannot be removed, check if the circle mark on the lock release lever is aligned with that on the toner cartridge.
  • Page 106 Take the toner cartridge out of the box, and then take it out of the protective pack. While holding the center portion on the top of the protective pack, open it to left and right. IMPORTANT Keep the protective pack for the toner cartridge. It may be required after taking out the toner cartridge for printer maintenance.
  • Page 107 While holding the tab, insert the toner cartridge into the printer , and then push it gently until it stops as shown in the figure. Insert the toner cartridge so that the orientation of the character on the toner cartridge and that on the toner cover match. Top View Match the orientation of the characters.
  • Page 108 Tilt the lock release lever (A) to the position of " ", to lock the toner cartridge. Align the triangular mark on the lock release lever with that on the toner cartridge. Top View Align at this part...

  • Page 109: Resetting The Counter Of Toner Cartridges

    Close the toner cover. IMPORTANT If you cannot close the toner cover, check if the toner cartridges are installed • properly. If you try to close the toner cover forcefully, this may result in damage to the printer or toner cartridges. Do not leave the toner cover open for a long time after installing the toner cartridge.

  • Page 110: In Case Of Lbp5910/5910F

    IMPORTANT Carry out this procedure only after you replaced a toner cartridge when < > (in case of LBP5910/5910F), or "Toner Cartridge Replacement Required" (in case of LBP5610) was not being displayed. In Case of LBP5910/5910F Press [ menu is displayed. With [ ] and [ ], select <...

  • Page 111: In Case Of Lbp5610

    NOTE If < > appears after resetting the counter of the toner cartridge, remove the replaced toner cartridge, hold the toner cartridge so that its tab is at the bottom, shake the cartridge up and down forcefully again to evenly distribute the toner inside the cartridge, and then install the toner cartridge.
  • Page 112 Click [Yes]. NOTE If "Toner Cartridge Replacement Required" is displayed after resetting the counter of the toner cartridge, remove the replaced toner cartridge, hold it with the tab facing down, shake it up and down strongly again, evenly distribute the toner inside the cartridge, and install it.

  • Page 113: Replacing The Drum Cartridges

    Replacing the Drum Cartridges This section describes how to replace drum cartridges. When a Message Appears Drum cartridges are consumable products. When any drum cartridge is nearing the end of its life, a message appears on the display in case of LBP5910/5910F, or on the Printer Status Window in case of LBP5610, so follow the directions in the message.
  • Page 114 Drum Cartridge 502 Magenta Drum Cartridge 502 Cyan NOTE The lifetime of the drum cartridges (Canon Genuine Drum Cartridge) used by LBP5910/ • 5910F is as follows. The numbers of the pages are estimated when printing in the following conditions.

  • Page 115: Precautions On Replacing The Drum Cartridges

    - Yellow (Drum Cartridge 502 Yellow): Approx. 50,000 pages - Magenta (Drum Cartridge 502 Magenta): Approx. 50,000 pages - Cyan (Drum Cartridge 502 Cyan): Approx. 50,000 pages The lifetime of the drum cartridge (Canon Genuine Drum Cartridge) used by LBP5610 is • as follows.
  • Page 116 The fixing unit and its surroundings (including the output area and the staple • cartridge for LBP5910F) inside the printer are hot during use. Do not touch the fixing unit and its surroundings. This may result in burns. IMPORTANT Be sure to use only the drum cartridge designed for this printer. •...
  • Page 117 When removing or installing the drum cartridge, work from the left side of the printer as • shown in the figure. Do not touch the high-voltage contacts (A) in the following position. This may result in • damage to the printer. - Right side of the ITB unit, inside the printer...
  • Page 118 - Drum cartridge guides Dispose of the packing materials according to local regulations. NOTE The packing materials may be changed in form or position to be placed, or may be added or removed without notice.

  • Page 119: Replacing The Drum Cartridges

    Replacing the Drum Cartridges Removing the Drum Cartridge to Be Replaced If using the multi-purpose tray, close it. Open the front cover. While pressing the lever on the right of the front cover, open the front cover toward you.
  • Page 120 IMPORTANT Before opening the front cover, make sure that the multi-purpose tray and the paper cassette of the printer are closed. Pull the fixing unit down toward you. While pressing the green lock release buttons (A) on the left and right side of the fixing unit a , hold the tabs (B) and pull the fixing unit down toward you b as shown in the figure.
  • Page 121 Open the top cover. Press the blue lock release button of the top cover. While holding the lever of the top cover, open the top cover.
  • Page 122 IMPORTANT Do not touch the transfer belt of the ITB unit and the ITB unit cover. If the transfer • belt is damaged, this may result in misfeeds or deterioration in print quality. The transfer belt of the ITB unit is supplied with a function that cleans itself, therefore, you do not need to clean the belt even when toner is on it.
  • Page 123 Slide the blue lock release lever (A) of the drum cartridge that you want to replace to the position of " ", and release the lock. Slide the blue lock release lever so that the triangular mark on the lock release lever matches that of the label.

  • Page 124: Installing A New Drum Cartridge

    Installing a New Drum Cartridge Take the new drum cartridge out of the box. Take the drum cartridge out of the protective bag. IMPORTANT Keep the protective bag for the drum cartridge. It may be required after taking out the drum cartridge for printer maintenance. There are two types of replacement drum cartridges.
  • Page 125 Continuation of "If a packing material is Continuation of "If tape is provided" provided" Remove the drying agent attached with Remove the drying agent attached with tape (1 piece) shown in the figure. tape (1 piece) shown in the figure. Remove the tape , and then remove the drying Remove the tape...
  • Page 126 Continuation of "If a packing material is Continuation of "If tape is provided" provided" Remove the packing materials (2 pieces) Remove the packing material attached with on the both sides. tape (B) (1 piece) shown in the figure. • Left side Remove the tape and packing material at the same time.
  • Page 127 Continuation of "If a packing material is Continuation of "If tape is provided" provided" Turn the drum cartridge over gently to the Remove the packing material attached with original side. tape (C) (1 piece) shown in the figure. Remove the tape , and then pull the packing material out When removing the tape, remove the tape gently...
  • Page 128 Continuation of "If a packing material is Continuation of "If tape is provided" provided" Remove the tape (1 piece) shown in the Remove the tape (3 pieces) shown in the figure. figure in order of a and b. The tape to be removed in has another tape attached to the rear end.
  • Page 129 Place paper on a flat surface, place the drum cartridge on it, and then fold back the tab (A) of the sealing tape as shown in the figure. IMPORTANT When placing the drum cartridge, be sure to place paper under the drum cartridge •...
  • Page 130 Pull the sealing tape (approx. 70 cm long) out gently and horizontally while supporting the drum cartridge. When pulling the sealing tape out, you may feel it to be heavy. However, because this is not printer malfunction, pull the sealing tape out completely. Support this part with your hand IMPORTANT...
  • Page 131 Pull the sealing tape out completely from the drum cartridge. If any tape remains in • the drum cartridge, this may result in poor print quality. Dispose of the removed sealing tape according to local regulations. • Before installing the drum cartridge, align the triangular mark on the lock release lever (A) with the triangular mark of "...
  • Page 132 Make sure that the levers (A) near the drum cartridge guides on the both sides are in the proper position as shown in the figure. If the levers are not in the proper position, the drum cartridges cannot be installed. Raise the levers to the proper position as shown in the figure. - Incorrect position - Correct position...
  • Page 133 Install the drum cartridge into the printer. Insert the drum cartridge firmly until it touches the back of the printer. Insert the projections (A) on each side of the drum cartridge into the drum cartridge guides as shown in the figure. - Drum cartridge guides (left) Yellow Magenta...
  • Page 134 Make sure that the levers near the drum cartridge guides on the both sides are in the proper position as shown in the figure. Make sure that the labels on the projections of the drum cartridge are visible. Make sure that all of the three colors on the label are visible.
  • Page 135 Slide the blue lock release lever (A) to the position of " " to lock the drum cartridge. Slide the blue lock release lever until the triangular mark on the lock release lever aligns with the triangular mark on the label. Align the triangular marks.
  • Page 136 ● LBP5910/5610 ❑ By pressing the portion indicated "PUSH", close the top cover firmly until it cannot be pressed down any further as shown in the figure. ● LBP5910F ❑ By pressing the top cover with both hands, close it firmly until it cannot be pressed down any further as shown in the figure.
  • Page 137 By holding the lever as shown in the figure, make sure that the top cover does not open. IMPORTANT Close the top cover firmly until it cannot be pressed down any further. If the top cover is not closed firmly, this may result in poor print quality. While holding the tabs (A), move the fixing unit back to its original position , and then press the tabs on the both sides...
  • Page 138 Close the front cover. While supporting the front cover a, push and close the front cover with both hands as shown in the figure b. CAUTION Push the front portion of the front cover to close it as shown in the figure. If closing the front cover by the levers on the both sides, you may catch your fingers, resulting in personal injury.

  • Page 139: Replacing The Waste Toner Container

    IMPORTANT When you are replacing the waste toner container, be sure to use the waste toner • container designed for this printer. Model Name Supported Canon Genuine Waste Toner Container LBP5910/5910F/5610 WASTE TONER BOX WT-98B...

  • Page 140: Precautions On Replacing The Waste Toner Container

    The waste toner container needs to be replaced soon. LBP5610 Waste Toner Container is Full NOTE The waste toner container (Canon Genuine Waste Toner Container) is full with approx. • 6,200 pages. The numbers of the pages are estimated when printing in the following conditions.
  • Page 141 The fixing unit and its surroundings (including the output area and the staple • cartridge for LBP5910F) inside the printer are hot during use. Do not touch the fixing unit and its surroundings. This may result in burns. IMPORTANT Be sure to use only the waste toner container designed for this printer. •...

  • Page 142: Replacing The Waste Toner Container

    Replacing the Waste Toner Container If using the multi-purpose tray, close it. Open the front cover. While pressing the lever on the right side of the front cover, open the front cover toward you.
  • Page 143 IMPORTANT Before opening the front cover, make sure that the multi-purpose tray and the paper cassette of the printer are closed. Hold the tab (A) on the waste toner cover, and open the waste toner cover.
  • Page 144 Remove the used waste toner container , then attach the supplied cap Take a new waste toner container out of the protective bag.
  • Page 145 Install the waste toner container. Make sure that the cap is not attached here. Close the waste toner cover.
  • Page 146 Close the front cover. While supporting the front cover a , push and close the front cover with both hands as shown in the figure b . CAUTION Push the front portion of the front cover to close it as shown in the figure. If closing the front cover by the levers on the both sides, you may catch your fingers, resulting in personal injury.

  • Page 147: Replacing The Staple Cartridge (Only For Lbp5910F)

    Supported Canon Genuine Staple Cartridge LBP5910F Staple-S1 NOTE The staple cartridge (Canon Genuine Staple Cartridge) used in this printer contains • 1,000 staples. The replacement staple cartridges are sold in a set of three. Even if the message < > or <...
  • Page 148 CAUTION The fixing unit and its surroundings (including the output area and the staple cartridge) inside the printer are hot during use. Make sure the staple cartridge is completely cool before replacing it. Touching the fixing unit when it is still hot may result in burns.

  • Page 149: Replacing The Staple Cartridge

    Replacing the Staple Cartridge If using the multi-purpose tray, close it. Open the front cover. While pressing the lever on the right side of the front cover, open the front cover toward you.
  • Page 150 IMPORTANT Before opening the front cover, make sure that the multi-purpose tray and the paper cassette of the printer are closed. Pull the fixing unit down toward you. While pressing the green lock release buttons (A) on the left and right side of the fixing unit a , hold the tabs (B) and pull the fixing unit down toward you b as shown in the figure.
  • Page 151 Holding the tab (A) of the staple cartridge, remove it from the printer. CAUTION The tab of the staple cartridge may be hot. Make sure the tab is completely cool before removing the staple cartridge. Touching the tab when it is still hot may result in burns.
  • Page 152 Holding the tab of the new staple cartridge, install it in the printer. Insert the staple cartridge until it clicks. IMPORTANT Insert the staple cartridge straight. If you apply force upward while inserting the staple cartridge, the tab may come off. If the tab comes off, put it back to the original position.
  • Page 153 While holding the tabs (A), move the fixing unit back to its original position , and then press the tabs on the both sides as shown in the figure...
  • Page 154 Close the front cover. While supporting the front cover a , push and close the front cover with both hands as shown in the figure b . CAUTION Push the front portion of the front cover to close it as shown in the figure. If closing the front cover by the levers on the both sides, you may catch your fingers, resulting in personal injury.

  • Page 155: Canceling A Job (Only For Lbp5910/5910F)

    Canceling a Job (Only for LBP5910/5910F) When you want to cancel the current job, perform "Job Cancel" using the following procedure. Job Cancel allows you to cancel the job that currently being received or processed. This option does not affect the next print data or the jobs that have not been processed yet.

  • Page 156: Deleting/Pausing/Resuming A Job (Only For Lbp5610)

    Deleting/Pausing/Resuming a Job (Only for LBP5610) You can delete, pause, or resume a job in the Printer Status Window. Display the Printer Status Window. When deleting or pausing the job, click the [Pause Job] button in the [Current Print Job] tab or [My Job Operation] tab. The following message is displayed and the [My Job Operation] tab is displayed by clicking the [Pause Job] button in the [Current Print Job] tab.
  • Page 157 Click the button for the desired operation from among the [Job Operation] buttons. ● Deleting a Job ❑ [Click [ ] (Delete Job). ● Pause a Job ❑ [Click [ ] (Pause Job). ● Resuming the Job ❑ [Click [ ] (Resume Job).

  • Page 158: Confirming The Printer Features

    Confirming the Printer Features In Case of LBP5910/5910F This printer has the function of Status Print that allows you to confirm such as the settings in the menu. Use these functions when required after installing and connecting the printer, for example when you want to check the operation. The Status Print prints the list of the functions and settings in the menu that can be used currently.

  • Page 159: In Case Of Lbp5610

    Confirm the contents of the Status Print. "Page Count" on the lower right of the Status Print shows the number of total print pages. IMPORTANT This is a sample of Status Print. The contents may differ from the Status Print printed by your printer.
  • Page 160 Display the Printer Status Window. From the [Options] menu in the Printer Status Window, select [Utility] ➞ [Configuration Page Print]. Click [OK].
  • Page 161 Confirm the contents of Configuration Page Print. IMPORTANT This is a sample of Configuration Page Print. The contents may differ from Configuration Page Print printed by your printer.

  • Page 162: Service Call Display

    (n indicates alphanumeric printer. characters) contact your local authorized Canon dealer. A problem has Follow the instructions 2 or later, and contact occurred in the fixing your local authorized Canon dealer.
  • Page 163 , disconnect the power plug from the AC power outlet , and then remove the ground wire from the ground terminal Contact your local authorized Canon dealer. When contacting your Canon dealer, please report the problems and eight-digit alphanumeric characters that you have noted.

  • Page 164: In Case Of Lbp5610

    In Case of LBP5610 When a problem has occurred and the printer does not work properly, the indicator (red) comes on and the following service call appears in the Printer Status Window. If the service call appears, cycle the power of the printer using the following procedure.
  • Page 165 Turn the printer OFF, wait for 10 seconds or longer, and then turn it ON again. After 10 seconds If the message does not reappear, the printer can be used as it is. If the message still appears, proceed to the next step. Note down the error code displayed in the Printer Status Window.
  • Page 166 , disconnect the power plug from the AC power outlet , and then remove the ground wire from the ground terminal Contact your local authorized Canon dealer. When contacting your Canon dealer, please report the problems and the error code that you have noted.

  • Page 167: Message List (Only For Lbp5910/5910F)

    Message List (Only for LBP5910/5910F) If the printer cannot print for any reason (an error is occurring) when using the printer, warning beep sounds, the indicator comes on, and an error message that indicates the contents of the trouble) appears on the display. When any remedy is required although this status does not affect the job (Warning), a warning message appears on the display.
  • Page 168 Message Cause and Remedy Cause The toner cartridge of Y (Yellow), M (Magenta), C (Cyan), or K (Black) is not installed or is not installed properly. Remedy Install the toner cartridge of displayed color, or install it properly. Cause The toner cartridge of Y (Yellow), M (Magenta), C (Cyan), or K (Black) is nearing the end of its life.
  • Page 169 Message Cause and Remedy Cause The toner cartridge of Y (Yellow), M (Magenta), C (Cyan), or K (Black) has reached the end of its life. Remedy Replace the toner cartridge of displayed color with a new one. Cause Toner is solidified on the bottom of the toner cartridge (a message is displayed regardless of replacing a new toner cartridge).
  • Page 170 Message Cause and Remedy Cause The drum cartridge of Y (Yellow), M (Magenta), C (Cyan), or K (Black) is nearing the end of its life. Remedy You can continue printing for a while, however have ready a new drum cartridge. <Warning message>...
  • Page 171 Message Cause and Remedy Cause The paper size that is selected in an application is not loaded in the paper cassette or the multi-purpose tray, or the paper source of the different paper size is selected. Remedy Load the paper of size that is set in an application (or scaling) in the selected paper cassette.

This manual is also suitable for:

Satera lbp5910Satera lbp5910f

Table of Contents