Advertisement
Quick Links
I.D. PRO Plus
Introduction
§ Features and Capabilities
§ Printer Comparison
Basic Operations
§ Setup
§ Keyboard
§ Functions
More line
Feed alignment
Serialization
Standard and bold printing
Tutorial
§ Battery and ribbon Installation
§ Label installation and removal
§ Printing labels
§ Serialization
Cleaning and Maintenance
Troubleshooting
§ Most commonly asked questions
Advertisement
Related Manuals for Brady I.D. PRO Plus
Summary of Contents for Brady I.D. PRO Plus
- Page 1 I.D. PRO Plus Introduction § Features and Capabilities § Printer Comparison Basic Operations § Setup § Keyboard § Functions More line Feed alignment Serialization Standard and bold printing Tutorial § Battery and ribbon Installation § Label installation and removal § Printing labels §...
-
Page 2: Features And Capabilities
Features and capabilities The I.D. Pro Plus is a highly portable self contained printing machine. The I.D. Pro Plus uses three different material widths and can print on a variety of materials (i.e..paper, polyester, vinyl cloth, self-laminating vinyl, nylon cloth, Tedlar ? , polyimide, and heat shrinkable materials). The I.D. -
Page 3: Basic Operations
Features BMXC LS2000 ID PRO PLUS Alignment, vertical & horizontal alignment of te xt Yes (vertical) Backing material out of unit Power reverse Bar code printing Battery, N-Cad battery pack Battery, plug-in type battery connector Bold print Built-in carrying handle Case, durable injection mold Case, hard carrying Included... - Page 4 Formats Strip - used when printing on Brady Strip series labels such that contain two or more butt cut pieces. Your text will show only once on the screen but will be duplicate the text to the number of strips indicated when printing.
- Page 5 Bold printing is supported in both large and small font modes. To toggle the bold setting on or off: 1. Press the Shift-O key combination. 2. Press the Up arrow key to toggle bold printing on or off. 3. Press the Enter key to exit. Batch serialization To print a batch of serialized labels: 1.
- Page 6 To print 8 stip markers in pairs of 2 numbered from 0000 to 0003. 1. Enter “0000" in the left hand marker display field. 2. Enter “0001" in the right hand marker display field. 3. Press the Shift-Serial key combination. 4.
- Page 7 Tutorial Install the battery and charge it for 4-5 hours. Select the corresponding material guide setting to match the width of the label you are using (i.e. ½", 1", or 1-1/2). Insert the labels onto the roll holder and place in the label holding area. Turn the unit on and with the arrow keys select the appropriate size code.
-
Page 8: Cleaning And Maintenance
Cleaning and maintenance Turn the unit off. Remove the labels and the bottom door. With a cotton swab and isopropyl alcohol clean the drive roller and the material guide nip roller. Drive roller cleaning - Turn the unit on. From the back of the unit run the cotton swab over the drive roller press ant Feed button (this will rotate the roller). -
Page 9: Troubleshooting And Frequently Asked Questions
Ribbon installation - Hold the ribbon cartridge over the ribbon compartment with the exposed ribbon facing toward you. Tilt the left side of the cartridge down and position the ribbon along the left side of the printer. Gently move the ribbon cartridge down and press it into the ribbon compartment until you hear it click into place. - Page 10 Q. How are non-warranty repairs handled by Brady? A. Brady will repair the unit and bill a flat rate of $140.00 (as of 1/1/2001 - subject to change) Q. Will Brady provide factory loaners while our customer's I.D. PRO Plus is being repaired? A.
- Page 11 Q. How is multiple serialization done? A. 1. Press the SHIFT-SERIAL key combination. 2. Enter a number from 1 to 99. 3. Press the SHIFT-PRINT key combination. 4. Enter a number from 1 to 99. 5. Press ENTER or PRINT to print or press CLEAR to cancel. More Troubleshooting Labels are not advancing a.