Page 1 Catalyst 6500 Series Switches Installation Guide June 2005 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-5781-04...
Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
Page 3 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the...
Page 5: Table Of Contents
Related Documentation Obtaining Documentation Cisco.com Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Obtaining Technical Assistance xxii Cisco Technical Support Website xxii Submitting a Service Request xxii Definitions of Service Request Severity...
Page 6 Contents Preparing for Installation C H A P T E R Safety Site Requirements Temperature Humidity Altitude Dust and Particles Corrosion Electromagnetic and Radio Frequency Interference Shock and Vibration Power Source Interruptions System Grounding Preventing Electrostatic Discharge Damage Air Flow 2-10 Power Requirements 2-20...
Page 7 Contents Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) 3-23 Replacing the Cable Guide 3-25 Establishing the System Ground 3-27 Required Tools and Parts 3-28 Connecting the System Ground 3-29 Installing the Power Supplies in the Switch Chassis 3-34 Attaching the Interface Cables 3-34 Connecting the Supervisor Engine Console Port...
Page 8 Contents Power Supply Specifications A P P E N D I X Power Supply Compatibility Matrix 950 W AC-Input and DC-Input Power Supplies 950 W Power Supply Specifications 950 W Power Supply AC Power Cords 1000 W AC-Input Power Supply 1000 W Power Supply Specifications A-10 1000 W Power Supply AC Power Cords...
Page 9: Troubleshooting E
Contents Module Connectors B-17 RJ-45 Connector B-17 RJ-21 Connector B-18 RJ-21 Connector (WS-X6624-FXS Only) B-21 SC Connector B-22 MT-RJ Connector B-22 LC Connector B-23 Cables B-24 Console Port Mode Switch B-26 Identifying a Rollover Cable B-26 Console Port Mode 1 Signaling and Pinouts B-27 Console Port Mode 2 Signaling and Pinouts B-28...
Page 10 Contents Catalyst 6500 Series Switches Installation Guide OL-5781-04...
Page 11: Preface
Preface This preface describes who should read the Catalyst 6500 Series Switch Installation Guide, how it is organized, and its document conventions. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment described in this publication. Organization This publication is organized as follows: Chapter...
Page 12: Conventions
Preface Conventions Chapter Title Description Appendix B Transceivers, Module Gives brief descriptions of the copper and optical Connectors, and Cable transceiver modules, physical connectors, and the cables Specifications used with the Catalyst 6500 series switches. Appendix C Repacking the Switch Provides procedures to repack your Catalyst 6500 series switch if you need to return it to the factory.
Page 13 Preface Conventions Convention Description font Terminal sessions and information the system displays screen are in font. screen Information you must enter is in font. boldface screen boldface screen font italic screen font Arguments for which you supply values are in italic screen font.
Page 14: Statement 1071-Warning Definition
Preface Conventions Warnings use the following conventions: Statement 1071—Warning Definition IMPORTANT SAFETY INSTRUCTIONS Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
Page 15 Preface Conventions Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
Page 16 Preface Conventions Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
Page 17 Preface Conventions Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Page 18 Preface Conventions Catalyst 6500 Series Switches Installation Guide xviii OL-5781-04...
Page 19: Related Documentation
Catalyst 6500 Series Switch IOS Command Reference ATM Software Configuration and Command Reference—Catalyst 5000 Family and Catalyst 6000 • Family Switches System Message Guide—Catalyst 6500 Series Switches • For information about MIBs, refer to this URL: • http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml Catalyst 6500 Series Switches Installation Guide OL-5781-04...
Page 20: Obtaining Documentation
Preface Obtaining Documentation Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/univercd/home/home.htm...
Page 21: Documentation Feedback
Register to receive security information from Cisco. • A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html...
Page 22: Obtaining Technical Assistance
Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
Page 23: Definitions Of Service Request Severity
Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Page 24 Preface Obtaining Additional Publications and Information iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies • learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions.
Page 25: Product Overview
C H A P T E R Product Overview This chapter describes the Catalyst 6500 series switches and contains these sections: Catalyst 6503 Switch, page 1-2 • • Catalyst 6503-E Switch, page 1-8 Catalyst 6504-E Switch, page 1-13 • • Catalyst 6506 Switch, page 1-18 Catalyst 6506-E Switch, page 1-24 •...
Page 26: Catalyst 6503 Switch
Chapter 1 Product Overview Catalyst 6503 Switch Catalyst 6503 Switch The Catalyst 6503 switch is a 3-slot horizontal chassis. Table 1-1 lists the features of the Catalyst 6503 switch chassis. Table 1-2 lists the specifications of the Catalyst 6503 switch chassis. Figure 1-1 shows the front view and...
Page 27 Chapter 1 Product Overview Catalyst 6503 Switch Table 1-1 Catalyst 6503 Switch Features (continued) Feature Description Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: FAN-MOD-3 (Standard fan tray—170 CFM). Supports Supervisor – Engine 1 and Supervisor Engine 2 only; does not support Supervisor Engine 32 or Supervisor Engine 720.
Page 28 Chapter 1 Product Overview Catalyst 6503 Switch Table 1-1 Catalyst 6503 Switch Features (continued) Feature Description Power Entry Module (PEM) A PEM is required for each installed power supply. • PEM-15A-AC (PEM for 950 W AC-input power supplies). – – PEM-DC/3 (PEM for 950 W DC-input power supplies).
Page 29 Chapter 1 Product Overview Catalyst 6503 Switch Table 1-2 Catalyst 6503 Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 30 Chapter 1 Product Overview Catalyst 6503 Switch Table 1-2 Catalyst 6503 Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 7 x 17.37 x 21.75 in. (17.78 x 44.12 x 55.25 cm). Chassis requires 4 RU •...
Page 31 Chapter 1 Product Overview Catalyst 6503 Switch Figure 1-2 Catalyst 6503 Switch—Rear View Power supply 2 (redundant) Power supply 1 Catalyst 6500 Series Switches Installation Guide OL-5781-04...
Page 32: Catalyst 6503-E Switch
Chapter 1 Product Overview Catalyst 6503-E Switch Catalyst 6503-E Switch The Catalyst 6503-E switch is a 3-slot horizontal chassis. Table 1-3 lists the features of the Catalyst 6503-E switch chassis. Table 1-4 lists the specifications of the Catalyst 6503-E switch chassis. Figure 1-3 shows the front view and Figure 1-4...
Page 33 Chapter 1 Product Overview Catalyst 6503-E Switch Table 1-3 Catalyst 6503-E Switch Features (continued) Feature Description Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: WS-C6503-E-FAN—282 CFM – Note The fan tray contains four individual fans. The individual fans are not field replaceable.
Page 34 Chapter 1 Product Overview Catalyst 6503-E Switch Table 1-4 Catalyst 6503-E Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 35 Chapter 1 Product Overview Catalyst 6503-E Switch Table 1-4 Catalyst 6503-E Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 7 x 17.37 x 21.75 in. (17.78 x 44.12 x 55.25 cm). Chassis requires 4 RU •...
Page 36 Chapter 1 Product Overview Catalyst 6503-E Switch Figure 1-3 Catalyst 6503-E Switch—Front View PEM 1 PEM 2 ESD ground strap connection WS-X6 K-SUP 2-2GE Supervisor Switch Load CONSOL E 100% PORT MODE PORT 1 CONSOL E SUPER VISOR 2 PORT 2 PCMCIA Engine EJECT...
Page 37: Catalyst 6504-E Switch
Chapter 1 Product Overview Catalyst 6504-E Switch Catalyst 6504-E Switch The Catalyst 6504-E switch is a 4-slot horizontal chassis. Table 1-5 lists the features of the Catalyst 6504-E switch chassis. Table 1-6 lists the specifications of the Catalyst 6504-E switch chassis. Figure 1-5 shows the front view and Figure 1-6...
Page 38 Chapter 1 Product Overview Catalyst 6504-E Switch Table 1-5 Catalyst 6504-E Switch Features (continued) Feature Description Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: FAN-MOD-4HS—300 CFM – Note The fan tray contains eight individual fans. The individual fans are not field replaceable.
Page 39 Chapter 1 Product Overview Catalyst 6504-E Switch Table 1-6 Catalyst 6504-E Switch Specifications (continued) Item Specification Humidity (RH), ambient 5% to 90% (noncondensing) operating Humidity (RH), ambient 5% to 95% (noncondensing) nonoperating and storage Altitude, operating Certified for operation: 0 to 6500 feet (0 to 2000 m) Designed and tested for: –200 to 10,000 feet (–60 to 3000 m) Shock and vibration This switch complies with Network Equipment Building Systems (NEBS)
Page 40 Chapter 1 Product Overview Catalyst 6504-E Switch Table 1-6 Catalyst 6504-E Switch Specifications (continued) Item Specification Airflow FAN-MOD-4HS—300 CFM • Note To maintain proper air circulation through the Catalyst switch chassis, we recommend that you maintain a minimum 6-inch (15 cm) separation between a wall and the chassis air intake or a wall and the chassis air exhaust.
Page 41 Chapter 1 Product Overview Catalyst 6504-E Switch Figure 1-6 Catalyst 6504-E Switch—Rear View P W R -2 70 0- A C 10 0- 24 0V -1 6A 50 /6 0H IN PU T FA N OU TP UT FA IL AL L FA ST EN ER PR IO R...
Page 42: Catalyst 6506 Switch
Chapter 1 Product Overview Catalyst 6506 Switch Catalyst 6506 Switch The Catalyst 6506 switch is a 6-slot horizontal chassis. Table 1-7 lists the features of the Catalyst 6506 switch chassis. Table 1-8 lists the specifications of the Catalyst 6506 switch chassis. Figure 1-7 shows the Catalyst 6506 switch.
Page 43 Chapter 1 Product Overview Catalyst 6506 Switch Table 1-7 Catalyst 6506 Switch Features (continued) Feature Descriptions Clock and VTT Modules Two replaceable clock modules (WS-C6K-CL=) provide clocking • signals to the EOBC channel and the switching bus. Three replaceable voltage termination (VTT) modules •...
Page 44 Chapter 1 Product Overview Catalyst 6506 Switch Table 1-7 Catalyst 6506 Switch Features (continued) Feature Descriptions Power Supply Supports one or two power supplies. The following power supplies are • supported: WS-CAC-1000W (1000 W AC-input power supply). – WS-CAC-1300W (1300 W AC-input power supply). –...
Page 45 Chapter 1 Product Overview Catalyst 6506 Switch Table 1-8 Catalyst 6506 Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 46 Chapter 1 Product Overview Catalyst 6506 Switch Table 1-8 Catalyst 6506 Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 20.1 x 17.2 x 18.1 in. (51.1 x 43.7 x 46.0 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). •...
Page 47 Chapter 1 Product Overview Catalyst 6506 Switch Figure 1-7 Catalyst 6506 Switch WS-X6K-SUP2-2 GE Supervisor engine Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Redundant supervisor Switch Load 100% CONSOLE PORT 1 PORT MODE PORT 2...
Page 48: Catalyst 6506-E Switch
Chapter 1 Product Overview Catalyst 6506-E Switch Catalyst 6506-E Switch The Catalyst 6506-E switch is a 6-slot horizontal chassis. Table 1-9 lists the features of the Catalyst 6506-E switch chassis. Table 1-10 lists the specifications of the Catalyst 6506-E switch chassis. Figure 1-8 shows the Catalyst 6506-E switch.
Page 49 Chapter 1 Product Overview Catalyst 6506-E Switch Table 1-9 Catalyst 6506-E Switch Features (continued) Feature Descriptions Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: WS-C6506-E-FAN—564 CFM – Note You must install a 2500 W or higher capacity power supply in the chassis to power the fan tray.
Page 50 Chapter 1 Product Overview Catalyst 6506-E Switch Table 1-10 Catalyst 6506-E Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 51 Chapter 1 Product Overview Catalyst 6506-E Switch Table 1-10 Catalyst 6506-E Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 19.2 x 17.5 x 18.2 in. (48.8 x 44.5 x 46.0 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). •...
Page 52: Catalyst 6509 Switch
Chapter 1 Product Overview Catalyst 6509 Switch Catalyst 6509 Switch The Catalyst 6509 switch is a 9-slot horizontal chassis. Table 1-11 lists the features of the Catalyst 6509 switch chassis. Table 1-12 lists the specifications of the Catalyst 6509 switch chassis. Figure 1-9 shows the Catalyst 6509 switch.
Page 53 Chapter 1 Product Overview Catalyst 6509 Switch Table 1-11 Catalyst 6509 Switch Features (continued) Feature Description Clock and VTT Modules Two replaceable clock modules (WS-C6K-CL=) provide clocking • signals to the EOBC channel and the switching bus. Three replaceable voltage termination (VTT) modules •...
Page 54 Chapter 1 Product Overview Catalyst 6509 Switch Table 1-11 Catalyst 6509 Switch Features (continued) Feature Description Power Supply Supports one or two power supplies. The following power supply • models are supported: WS-CAC-1000W (1000 W AC-input power supply). – WS-CAC-1300W (1300 W AC-input power supply). –...
Page 55 Chapter 1 Product Overview Catalyst 6509 Switch Table 1-12 Catalyst 6509 Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 56 Chapter 1 Product Overview Catalyst 6509 Switch Table 1-12 Catalyst 6509 Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 25.2 x 17.2 x 18.4 in. (64.0 x 43.7 x 46.7 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). •...
Page 57 Chapter 1 Product Overview Catalyst 6509 Switch Figure 1-9 Catalyst 6509 Switch WS-X6K-SUP2-2 GE Supervisor engine Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Redundant supervisor Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE...
Page 58: Catalyst 6509-E Switch
Chapter 1 Product Overview Catalyst 6509-E Switch Catalyst 6509-E Switch The Catalyst 6509-E switch is a 9-slot horizontal chassis. Table 1-13 lists the features of the Catalyst 6509-E switch chassis. Table 1-14 lists the specifications of the Catalyst 6509-E switch chassis. Figure 1-10 shows the Catalyst 6509-E switch.
Page 59 Chapter 1 Product Overview Catalyst 6509-E Switch Table 1-13 Catalyst 6509-E Switch Features (continued) Feature Description Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: WS-C6509-E-FAN—846 CFM – Note You must install a 2500 W or higher capacity power supply in the chassis to power the high-speed fan tray.
Page 60 Chapter 1 Product Overview Catalyst 6509-E Switch Table 1-14 Catalyst 6509-E Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 61 Chapter 1 Product Overview Catalyst 6509-E Switch Table 1-14 Catalyst 6509-E Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 24.5 x 17.5 x 18.2 in. (62.2 x 44.5 x 46.0 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). •...
Page 62 Chapter 1 Product Overview Catalyst 6509-E Switch Figure 1-10 Catalyst 6509-E Switch WS-X6K-SUP2-2 GE Supervisor engine Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Redundant supervisor Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 CONSOLE...
Page 63: Catalyst 6509-Neb Switch
Chapter 1 Product Overview Catalyst 6509-NEB Switch Catalyst 6509-NEB Switch The Catalyst 6509-NEB switch is a 9-slot vertical chassis. Table 1-15 lists the features of the Catalyst 6509-NEB switch chassis. Table 1-16 lists the specifications of the Catalyst 6509-NEB switch chassis.
Page 64 Chapter 1 Product Overview Catalyst 6509-NEB Switch Table 1-15 Catalyst 6509-NEB Switch Features (continued) Feature Features Fan Tray Supports one hot-swappable fan tray. These fan tray models are • supported: WS-C6509-NEB-FAN (Standard fan tray—294 CFM). Supports – Supervisor Engine 1 and Supervisor Engine 2 only; does not support Supervisor Engine 32 or Supervisor Engine 720.
Page 65 Single power supplies are installed in the left power supply bay. The • second power supply is installed in the right power supply bay. 1. Refer to the Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note for kit installation instructions. Catalyst 6500 Series Switches Installation Guide 1-41...
Page 66 Chapter 1 Product Overview Catalyst 6509-NEB Switch Table 1-16 Catalyst 6509-NEB Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 67 Chapter 1 Product Overview Catalyst 6509-NEB Switch Table 1-16 Catalyst 6509-NEB Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 33.3 x 17.2 x 18.1 in. (84.6 x 43.7 x 46.0 cm). Chassis requires 20 RU •...
Page 68 Chapter 1 Product Overview Catalyst 6509-NEB Switch Figure 1-11 Catalyst 6509-NEB Switch Switching modules STATUS assembly Supervisor engine Redundant supervisor engine Slots 1-9 (right to left) INPUT OUTPUT FAIL INPUT OUTPUT FAIL Power supply 2 Power supply 1 (redundant) ESD ground strap connection Catalyst 6500 Series Switches Installation Guide 1-44...
Page 69: Catalyst 6509-Neb-A Switch
Chapter 1 Product Overview Catalyst 6509-NEB-A Switch Catalyst 6509-NEB-A Switch Table 1-17 lists the features of the Catalyst 6509-NEB-A switch chassis. Table 1-18 lists the specifications of the Catalyst 6509-NEB-A switch chassis. Figure 1-12 shows the Catalyst 6509-NEB-A switch chassis. Table 1-17 Catalyst 6509-NEB-A Switch Features Feature Description...
Page 70 Chapter 1 Product Overview Catalyst 6509-NEB-A Switch Table 1-17 Catalyst 6509-NEB-A Switch Features (continued) Feature Description Fan Tray Supports two hot-swappable fan trays. These fan tray models are • supported: FAN-MOD-09 (High-speed fan tray—760 CFM). Supports – Supervisor Engine 1, Supervisor Engine 2, Supervisor Engine 32, and Supervisor Engine 720.
Page 71 Chapter 1 Product Overview Catalyst 6509-NEB-A Switch Table 1-18 Catalyst 6509-NEB-A Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 72 Chapter 1 Product Overview Catalyst 6509-NEB-A Switch Table 1-18 Catalyst 6509-NEB-A Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 36.7 x 17.2 x 20.3 in. (93.1 x 43.7 x 51.6 cm). Chassis requires 21 RU •...
Page 73 Chapter 1 Product Overview Catalyst 6509-NEB-A Switch Figure 1-12 Catalyst 6509-NEB-A Switch Chassis assemblies Supervisor engine Redundant supervisor engine Slots 1-9 (right to left) POWE R SUPP LY 1 POWE R SUPP LY 2 INPUT OUTPUT FAIL INPUT OUTPUT FAIL Power supply 1 Power supply 2 (redundant)
Page 74: Catalyst 6513 Switch
Chapter 1 Product Overview Catalyst 6513 Switch Catalyst 6513 Switch Table 1-19 lists the features of the Catalyst 6513 switch chassis. Table 1-20 lists the specifications of the Catalyst 6513 switch chassis. Figure 1-13 shows a view of the Catalyst 6513 switch chassis. Table 1-19 Catalyst 6513 Switch Features Feature Description...
Page 75 Chapter 1 Product Overview Catalyst 6513 Switch Table 1-19 Catalyst 6513 Switch Features (continued) Feature Description Backplane Bandwidth 32 GBps shared bus. • 256 GBps switch fabric. • • 720 GBps switch fabric. Clock and VTT Module Two replaceable clock modules (WS-C6513-CL=) provide clocking •...
Page 76 Chapter 1 Product Overview Catalyst 6513 Switch Table 1-19 Catalyst 6513 Switch Features (continued) Feature Description Power Supply Supports one or two power supplies. The following models are • supported: WS-CAC-2500W (2500 W AC-input power supply). – WS-CDC-2500W (2500 W DC-input power supply). –...
Page 77 Chapter 1 Product Overview Catalyst 6513 Switch Table 1-20 Catalyst 6513 Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Note The Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 40°C (104°F) generating a minor alarm and at 55°C (131°F) generating a major alarm.
Page 78 Chapter 1 Product Overview Catalyst 6513 Switch Table 1-20 Catalyst 6513 Switch Specifications (continued) Item Specification Physical Characteristics Dimensions (H x W x D) • 33.3 x 17.2 x 18.1 in. (84.6 x 43.7 x 46.0 cm). Chassis requires 20 RU •...
Page 79 Chapter 1 Product Overview Catalyst 6513 Switch Figure 1-13 Catalyst 6513 Switch WS-X6K-SUP2- 2GE Supervisor engine Switch Load CONSOLE 100% PORT MODE PORT 1 CONSOLE PORT 2 SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2- 2GE Redundant supervisor Switch Load CONSOLE 100% PORT PORT 1 CONSOLE MODE PORT 2...
Page 80 Chapter 1 Product Overview Catalyst 6513 Switch Catalyst 6500 Series Switches Installation Guide 1-56 OL-5781-04...
Page 81: Chapter 2 Preparing For Installation
C H A P T E R Preparing for Installation In this publication, the term Catalyst 6500 series refers only to the switch chassis listed in Chapter 1. Note The Catalyst 6000 series switches (Catalyst 6006 and Catalyst 6009 switches) are described in a separate publication, the Catalyst 6000 Series Switch Installation Guide.
Page 82: Safety
Chapter 2 Preparing for Installation Safety Safety Safety warnings appear throughout this publication in procedures that may harm you if performed incorrectly. A warning symbol precedes each warning statement. The warnings below are general warnings that are applicable to the entire publication. Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Page 83: Temperature
Chapter 2 Preparing for Installation Site Requirements Temperature Temperature extremes can cause a system to operate at reduced efficiency and cause a variety of problems, including premature aging and failure of chips, and failure of mechanical devices. Extreme temperature fluctuations can cause chips to become loose in their sockets. Ensure that the system is operating in an environment no colder than 50°F (10°C) or hotter than 95°F (35°C).
Page 84: Dust And Particles
Chapter 2 Preparing for Installation Site Requirements Dust and Particles Exhaust fans cool power supplies and system fan trays cool systems by drawing in air and exhausting air out through various openings in the chassis. However, fans also ingest dust and other particles, causing contaminant buildup in the system and increased internal chassis temperature.
Page 85: Shock And Vibration
Chapter 2 Preparing for Installation Site Requirements To predict and remedy strong EMI, you may also need to consult experts in radio frequency interference Note (RFI). If you use twisted-pair cable in your plant wiring with a good distribution of grounding conductors, the plant wiring is unlikely to emit radio interference.
Page 86: System Grounding
Chapter 2 Preparing for Installation Site Requirements System Grounding Grounding is one of the most important parts of equipment installation. Proper grounding practices ensure that the buildings and the installed equipment within them have low-impedance connections and low-voltage differentials between chassis. When you properly ground systems during installation, you reduce or prevent shock hazards, equipment damage due to transients, and data corruption.
Page 87: Preventing Electrostatic Discharge Damage
Chapter 2 Preparing for Installation Site Requirements In all situations, grounding practices must comply with local National Electric Code (NEC) Note requirements or local laws and regulations. In installations where FXS modules are installed, supplemental grounding is required. Note Always ensure that all of the modules are completely installed and that the captive installation screws Note are fully tightened.
Page 88 Chapter 2 Preparing for Installation Site Requirements After you install the system ground lug, follow these steps to correctly attach the ESD wrist strap: Step 1 Attach the ESD wrist strap to bare skin as follows: If you are using the ESD wrist strap supplied with the FRUs, open the wrist strap package and unwrap the ESD wrist strap.
Page 89 Chapter 2 Preparing for Installation Site Requirements Figure 2-1 Attaching the ESD Wrist Strap Clip to the System Ground Lug Screw Clip ESD ground Grounding lug strap Screw Side view of Slide clip grounding lug behind screw Clip installed System ground behind screw connector WS-X6 K-SUP 2-2GE...
Page 90: Air Flow
Chapter 2 Preparing for Installation Site Requirements Air Flow The system fan assembly provides cooling air for the supervisor engine and the switching modules. Table 2-2 lists the Catalyst 6500 series switch chassis along with the supported and unsupported fan trays.
Page 91 Chapter 2 Preparing for Installation Site Requirements Plan ahead. Your Catalyst 6500 series switches currently installed in an enclosed or partially • enclosed rack might meet ambient air temperature and air flow requirements now. However, if you add more chassis to the rack or you add more modules to a chassis in the rack, the additional heat generated might cause the ambient air temperature within the rack to exceed 40°C (104°F) and can cause minor alarms.
Page 92 Chapter 2 Preparing for Installation Site Requirements Table 2-3 Chassis Air Flow Requirements Airflow Airflow Air Filter Minimum Clearance Minimum Clearance Reference Chassis Model Intake Exhaust Available (Walls) (Intakes to Exhausts) Illustration Catalyst 6503 Right side Left side 6 in (15.2 cm) 12 in (30.5 cm) Figure 2-2 Catalyst 6503-E...
Page 93 Chapter 2 Preparing for Installation Site Requirements Figure 2-3 Catalyst 6504-E Switch Internal Airflow Module air exhaust FA N ST AT U Module air inlet Figure 2-4 Catalyst 6506 Switch Internal Airflow assembly WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE...
Page 94 Chapter 2 Preparing for Installation Site Requirements Figure 2-5 Catalyst 6506-E Switch Internal Airflow assembly WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT Module WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 Module air...
Page 95 Chapter 2 Preparing for Installation Site Requirements Figure 2-6 Catalyst 6509 Switch Internal Airflow assembly WS-X6K-SUP2-2GE Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2...
Page 96 Chapter 2 Preparing for Installation Site Requirements Figure 2-7 Catalyst 6509-E Switch Internal Airflow assembly WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE...
Page 97 Chapter 2 Preparing for Installation Site Requirements Figure 2-8 Catalyst 6509-NEB Switch Internal Airflow Module air exhaust (3x) STATUS assembly Module air inlet Power supply air exhaust Power supply air inlet INPUT OUTPUT FAIL INPUT OUTPUT FAIL Catalyst 6500 Series Switches Installation Guide 2-17 OL-5781-04...
Page 98 Chapter 2 Preparing for Installation Site Requirements Figure 2-9 Catalyst 6509-NEB-A Switch Internal Airflow Module air exhaust assemblies Power supply air exhaust Module POWE R SUPP LY 1 air inlet POWE R SUPP LY 2 Power supply air inlet INPUT OUTPUT FAIL INPUT...
Page 99: Power Requirements
Chapter 2 Preparing for Installation Power Requirements Figure 2-10 Catalyst 6513 Switch Internal Airflow assembly WS-X6K-SUP2- 2GE Switch Load CONSOLE 100% PORT MODE PORT 1 CONSOLE PORT 2 SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2- 2GE Switch CONSOLE 100% Load PORT PORT 1 CONSOLE MODE SUPERVISOR2...
Page 100: Power Requirements
Chapter 2 Preparing for Installation Power Requirements You can connect the DC-input power supply to the power source with heavy gauge wiring connected • to a terminal block. The wire gauge size is determined by local electrical codes and restrictions. If you are using a 200/240 VAC power source in North America, the circuit must be protected by a •...
Page 101: Power Connection Guidelines For Dc-Powered Systems
We strongly recommend that power cabling runs and other potential noise sources be located as far away Caution as practical from LAN cabling that terminates on Cisco equipment. In situations, where this type of long parallel cable runs exist which cannot be separated by at least 3.3 feet (1 meter), we recommend that you shield these potential noise sources.
Page 102: Site Preparation Checklist
Chapter 2 Preparing for Installation Site Preparation Checklist Also be aware of the following caution concerning the use of Category 5e and Category 6 Ethernet cables: Caution Category 5e and Category 6 cables can store large levels of static electricity because of the dielectric properties of the materials used in their construction.
Page 103 Chapter 2 Preparing for Installation Site Preparation Checklist Table 2-4 Site Planning Checklist (continued) Task No. Planning Activity Verified By Time Date Cable and interface equipment evaluation: Cable type • • Connector type • Cable distance limitations Interface equipment (transceivers) •...
Page 104 Chapter 2 Preparing for Installation Site Preparation Checklist Catalyst 6500 Series Switches Installation Guide 2-24 OL-5781-04...
Page 105: Installing The Switch
C H A P T E R Installing the Switch In this publication, the term Catalyst 6500 series refers only to the switch chassis listed in Chapter 1. Note The Catalyst 6000 series switches (Catalyst 6006 and Catalyst 6009 switches) are described in a separate publication, the Catalyst 6000 Series Switch Installation Guide.
Page 106: Unpacking The Switch
Chapter 3 Installing the Switch Unpacking the Switch This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Warning Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both.
Page 107: Installing The Rack-Mount Kit
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Installing the Rack-Mount Kit This section describes how to install the rack-mount kit. The kit contains a shelf bracket and crossbar assembly that attaches directly to the rack. The Catalyst 6500 series switch chassis also have L brackets that are used to secure the chassis to the rack.
Page 108 Chapter 3 Installing the Switch Installing the Rack-Mount Kit The rack must have sufficient vertical clearance to insert the chassis. The chassis heights are as • follows: Catalyst 6503 switch—7 inches (17.8 cm) (4 RU) – Catalyst 6503-E switch—7 inches (17.8 cm) (4 RU) –...
Page 109: Required Tools
Chapter 3 Installing the Switch Installing the Rack-Mount Kit This rack-mounting kit is not suitable for use with racks that have obstructions (such as power strips) because the obstructions could impair access to switch field-replaceable units (FRUs). Required Tools These tools and equipment are required to install the rack-mount kit: Number 1 and number 2 Phillips screwdrivers •...
Page 110: Switches
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Figure 3-2 Attaching the Crossbar Bracket to the Shelf Brackets Front of rack Shelf bracket Shelf bracket Crossbar M3 screw bracket M3 screw Installing the L Brackets and Cable Guides on the Catalyst 6503 and the Catalyst 6503-E Switches The Catalyst 6503 and the Catalyst 6503-E switch chassis are normally shipped with the L brackets Note...
Page 111: Installing The L Brackets And Cable Guides On The Catalyst 6504-E Switch
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Figure 3-3 Installing the L-Brackets on the Catalyst 6503 and the Catalyst 6503-E Switch Chassis WS-X6K -SUP2-2 GE Switch Load CONSOLE 100% PORT MODE PORT 1 CONSOLE SUPERV ISOR2 PORT 2 PCMCIA EJECT OSM-4OC1 2 POS-SI...
Page 112: Installing The L Brackets And Cable Guides On The Catalyst 6506 And Catalyst 6506-E Switches
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Figure 3-4 Installing the L-Brackets on the Catalyst 6504-E Switch Chassis FA N ST AT U Installing the L Brackets and Cable Guides on the Catalyst 6506 and Catalyst 6506-E Switches The Catalyst 6506 and Catalyst 6506-E switch chassis is normally shipped with the L brackets installed.
Page 113 Chapter 3 Installing the Switch Installing the Rack-Mount Kit Figure 3-5 Attaching L Brackets and Cable Guides: Catalyst 6506 and Catalyst 6506-E Switch L-bracket WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load...
Page 114: Installing The L Brackets And Cable Guides On The Catalyst 6509 And Catalyst 6509-E Switches
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Installing the L Brackets and Cable Guides on the Catalyst 6509 and Catalyst 6509-E Switches Note The Catalyst 6509 and Catalyst 6509-E switch chassis are normally shipped with the L brackets installed.
Page 115: Installing The L Brackets And Cable Guides On The Catalyst 6509-Neb Switch
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Figure 3-6 Attaching L Brackets and Cable Guides: Catalyst 6509 Switch and Catalyst 6509-E Switch L-bracket WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch...
Page 116 Chapter 3 Installing the Switch Installing the Rack-Mount Kit The optional cable guide installs on the front of the chassis and is secured with four M4 screws. To install the L brackets, follow these steps: Position one of the L brackets against the switch chassis side, and align the screw holes. (Use either the Step 1 + or the –...
Page 117: Installing The L Brackets On The Catalyst 6509-Neb-A Switch
Chapter 3 Installing the Switch Installing the Rack-Mount Kit Installing the L Brackets on the Catalyst 6509-NEB-A Switch The Catalyst 6509-NEB-A switch chassis is shipped with the mounting brackets installed on the front of the chassis. These brackets can be installed on the rear of the chassis. To install the brackets on the rear of the chassis, perform these steps: Step 1 Remove the screws that secure the brackets to the chassis.
Page 118: Installing The Switch Chassis In The Rack
Chapter 3 Installing the Switch Installing the Switch Chassis in the Rack Installing the Switch Chassis in the Rack If you are not installing the Catalyst 6509-NEB switch, Catalyst 6509-NEB-A switch, or Catalyst 6513 Note switch in the rack, see “Installing the Stabilizer Kit”...
Page 119 Chapter 3 Installing the Switch Installing the Switch Chassis in the Rack If you are rack-mounting the Catalyst 6513 switch and you want to install the optional cable Note guides, perform Step 5; if not, go to Step 6. Align the cable guide bracket mounting holes with the mounting holes in the L bracket and the mounting Step 4 holes in the equipment rack, and install ten (five per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws, as shown in...
Page 120: Installing The Stabilizer Bracket Kit
Chapter 3 Installing the Switch Installing the Stabilizer Kit Installing the Stabilizer Kit The stabilizer kit is included only in the accessory kits for the Catalyst 6509-NEB, Note Catalyst 6509-NEB-A, and the Catalyst 6513 switches. If you are not installing a Catalyst 6509-NEB, Catalyst 6509-NEB-A, or Catalyst 6513 switch in a rack, you must install stabilizer brackets to the bottom of the chassis.
Page 121 Chapter 3 Installing the Switch Installing the Stabilizer Kit To install the stabilizer brackets, follow these steps: Step 1 Have one person tilt and hold the chassis to one side. Step 2 With the chassis tilted, attach the stabilizer bracket to the side of the chassis with the eight M4 screws, as shown in Figure 3-10.
Page 122: Installing The Cable Management System (Catalyst 6509-Neb-A Switch Only)
Chapter 3 Installing the Switch Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) This section describes the installation procedures for the Catalyst 6509-NEB-A switch cable management system (CABLETRAY-09). The cable management system is shipped with the extended cable guide installed but can be used with Note the supplied standard cable guide.
Page 123 Chapter 3 Installing the Switch Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) Loosen the two captive installation screws on the front panel. (See Figure 3-12.) Step 3 Figure 3-12 Removing the Front Panel STATU S Captive installation screws Remove the front panel, and set it aside.
Page 124: Replacing The Cable Guide
Chapter 3 Installing the Switch Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) Replacing the Cable Guide To replace the cable guides on the cable management system, perform these steps: Step 1 Loosen the two captive installation screws on the front panel. (See Figure 3-13.) Figure 3-13 Removing the Front Panel...
Page 125 Chapter 3 Installing the Switch Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only) Install the standard cable guide to the back panel by hooking the lip of the cable guide to the back panel. Step 4 (See Figure 3-14.) Install the two screws to secure the cable guide to the back plate.
Page 126: Establishing The System Ground
Chapter 3 Installing the Switch Establishing the System Ground Establishing the System Ground This section describes how to connect a system ground to the Catalyst 6500 series switches. Note This system ground is also referred to as the network equipment building system (NEBS) ground. You must use the system (NEBS) ground on both AC- and DC-powered systems if you are installing Foreign Exchange Station (FXS) modules or if you are installing this equipment in a U.S.
Page 127: Connecting The System Ground
Chapter 3 Installing the Switch Establishing the System Ground Connecting the System Ground To attach the grounding lug and cable to the grounding pad, follow these steps: Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding wire.
Page 128 Chapter 3 Installing the Switch Establishing the System Ground Figure 3-16 System Ground Location (Catalyst 6503 and Catalyst 6503-E Chassis) System ground connector Wire Grounding lug System ground connector WS-X6 K-SUP 2-2GE Switch Load CONSOL E 100% PORT MODE PORT 1 CONSOL E SUPER VISOR 2 PORT 2...
Page 129 Chapter 3 Installing the Switch Establishing the System Ground Figure 3-18 System Ground Location (Catalyst 6506, Catalyst 6509, and Catalyst 6509-NEB Chassis) WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load 100%...
Page 130 Chapter 3 Installing the Switch Establishing the System Ground Figure 3-19 System Ground Location (Catalyst 6506-E, Catalyst 6509-E, and Catalyst 6513 Chassis) WS-X6K-SUP2- 2GE Switch 100% Load CONSOLE PORT PORT 1 CONSOLE MODE SUPERVISOR2 PORT 2 PCMCIA EJECT WS-X6K-SUP2- 2GE Switch Load CONSOLE...
Page 131 Chapter 3 Installing the Switch Establishing the System Ground Figure 3-20 System Ground Location (Catalyst 6509-NEB-A) System ground connector Grounding lug Wire System ground connectors POWE R SUPPL Y 1 POWE R SUPPL Y 2 INPUT OUTPUT FAIL INPUT OUTPUT FAIL Catalyst 6500 Series Switches Installation Guide 3-27...
Page 132: Installing The Power Supplies In The Switch Chassis
Chapter 3 Installing the Switch Installing the Power Supplies in the Switch Chassis Installing the Power Supplies in the Switch Chassis The switch power supplies (AC or DC) are shipped separately from the switch chassis. Remove the power supply from its shipping packaging, and then install and connect it to the site power by referring to the “Removing and Installing the AC-Input Power Supplies”...
Page 133 Chapter 3 Installing the Switch Attaching the Interface Cables To connect a terminal to the console port using the cable and adapters provided, follow these steps: Step 1 Place the console port mode switch in the in position (factory default). Step 2 Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or RJ-45-to-DB-9 DTE adapter (labeled “Terminal”).
Page 134: Connecting The Supervisor Engine Uplink Ports
Chapter 3 Installing the Switch Attaching the Interface Cables Connecting the Supervisor Engine Uplink Ports This section describes how to connect to the supervisor engine uplink ports. Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments.
Page 135 Step 8 information about fiber-optic inspection and cleaning.) For complete information on inspecting and cleaning fiber-optic connections, refer to the document at this URL: http://www.cisco.com/en/US/tech/tk482/tk607/technologies_white_paper09186a0080254eba.shtml Step 9 Remove the dust plugs from the GBIC transceiver optical bores. Step 10 Immediately attach the network interface cable SC connector to the GBIC transceiver.
Page 136 Chapter 3 Installing the Switch Attaching the Interface Cables Observe the port status LED: Step 12 The LED turns green when the GBIC transceiver and the target device have an established link. • The LED turns amber while the GBIC discovers the network topology and searches for loops. •...
Page 137 Ensure that you are installing the SFP transceiver in the correct orientation for your Cisco device. For more details, refer to the hardware installation instructions that shipped along with your Cisco device.
Page 138 Chapter 3 Installing the Switch Attaching the Interface Cables Remove the dust plugs from the SFP transceiver optical bores. Step 9 Immediately attach the network interface cable LC connector to the SFP transceiver. Step 10 To connect 1000BASE-T SFP transceivers to a copper network, perform the following substeps: Step 11 To comply with GR-1089 intrabuilding lightning immunity requirements, you must use grounded, Caution...
Page 139: Verifying Switch Chassis Installation
Chapter 3 Installing the Switch Verifying Switch Chassis Installation Verifying Switch Chassis Installation To verify the switch chassis installation, follow these steps: Verify that the ejector levers of each module are fully closed (parallel to the faceplate) to ensure that the Step 1 supervisor engine and all switching modules are fully seated in the backplane connectors.
Page 140: Online Diagnostics
Verifying Switch Chassis Installation Online Diagnostics The Catalyst 6500 series systems running Cisco IOS have many levels of online diagnostic capabilities. The online diagnostics are divided into four categories: Bootup—Bootup diagnostics automatically run during bootup, module OIR, or switchover to a backup supervisor engine.
Page 141: Chapter 4 Removal And Replacement Procedures
C H A P T E R Removal and Replacement Procedures In this publication, the term Catalyst 6500 series refers only to the switch chassis listed in Chapter 1. Note The Catalyst 6000 series switches (Catalyst 6006 and Catalyst 6009 switches) are described in a separate publication, the Catalyst 6000 Series Switch Installation Guide.
Page 142: Removing And Installing The Ac-Input Power Supplies
Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Removing and Installing the AC-Input Power Supplies This section describes how to remove and install AC power supplies in the Catalyst 6500 series chassis. The AC-input power supplies have three different form factors, which are not interchangeable between the Catalyst 6500 series chassis.
Page 143 4-3, and slide the power supply completely out of the chassis. If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco Step 6 part number 800-16727-01 for the Catalyst 6503 and Catalyst 6503-E switches) over the opening, and secure it with the captive installation screws.
Page 144 Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Figure 4-1 Catalyst 6503 and Catalyst 6503-E Switches—PEM Location PEM 1 PEM 2 WS-X6 K-SUP 2-2GE Switch Load CONSOL E 100% PORT MODE PORT 1 CONSOL E SUPER VISOR 2 PORT 2 PCMCIA...
Page 145 Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Figure 4-3 Handling an AC-Input Power Supply Installing a 950 W or 1400 W AC-Input Power Supply Follow these steps to install an AC-input power supply: Ensure that the system (earth) ground connection has been made. For ground connection instructions, Step 1 see the “Establishing the System Ground”...
Page 146: Removing And Installing The 2700 W Ac-Input Power Supply
Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Connect the other end of the power cord to an AC-input power source. Step 6 In a system with dual power supplies, connect each power supply to a separate input source. In case Caution of a power source failure, the second source should still be available.
Page 147 Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Removing a 2700 W AC-Input Power Supply To remove a 2700 W AC-input power supply, follow these steps: Turn the power switch to the Off (0) position on the power supply you are removing. Step 1 Disconnect the power cord from the power source.
Page 148 Figure 4-5 Handling a 2700 W AC-Input Power Supply If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco Step 6 part number 800-16727-01) over the opening and secure it with the captive installation screws.
Page 149: Removing And Installing The 1000 W, 1300 W, 2500 W, 3000 W, 4000 W, And 6000 W Ac-Input Power Supplies
Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Power supply captive installation screws must be tight to ensure protective grounding continuity. Warning Statement 289 Plug the power cord into the power supply AC-in receptacle. Step 6 Connect the other end of the power cord to the AC-input power source.
Page 150 4-7, and slide the power supply completely out of the chassis. If the power supply bay is to remain empty, install a blank faceplate (Cisco part number 700-03104-01) Step 6 over the opening, and secure it with the captive installation screw.
Page 151 “Establishing the System Ground” section on page 3-22. If necessary, remove the blank faceplate (Cisco part number 700-03104-01) from the chassis power Step 2 supply bay opening by loosening the captive installation screw. Verify that the power switch is in the Off (0) position on the power supply that you are installing.
Page 152 Chapter 4 Removal and Replacement Procedures Removing and Installing the AC-Input Power Supplies Grasp the power supply handle with one hand. Place your other hand underneath the power supply, as Step 4 shown in Figure 4-7. Slide the power supply into the power supply bay. Make sure that the power supply is fully seated in the bay.
Page 153: Removing And Installing The Dc-Input Power Supplies
Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Removing and Installing the DC-Input Power Supplies This section covers the DC-input power supply removal and installation procedure for the Catalyst 6500 series switches and is divided into the following topics: Removing and Installing a 950 W DC-Input Power Supply, page 4-13 •...
Page 154 4-10, and slide the power supply completely out of the chassis. If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco Step 4 part number 800-16727-01) over the opening, and secure it with the captive installation screws.
Page 155 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-9 950 W DC-Input Power Supply Captive Installation Screws Status LEDs Captive installation screws Figure 4-10 Catalyst 6503 Switch—Handling a DC-Input Power Supply Catalyst 6500 Series Switches Installation Guide 4-15 OL-5781-04...
Page 156 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Installing a 950 W DC-Input Power Supply Before performing any of the following procedures, ensure that power is removed from the DC Warning circuits. To ensure that all power is removed, locate the circuit breakers or fuses on the DC power lines that service the DC circuits.
Page 157: Removing And Installing A 1300 W Or 2500 W Dc-Input Power Supply
Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Removing and Installing a 1300 W or 2500 W DC-Input Power Supply This section covers the power supply removal and installation procedures for the 1300 W and the 2500 W DC-input power supplies and is divided into the following topics: Required Tools, page 4-17 •...
Page 158 Set the power supply aside. Step 7 If the power supply bay is to remain empty, install a blank faceplate (Cisco part number 700-03104-01) over the opening, and secure it with the captive installation screw.
Page 159 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-12 DC-Input Power Supply Front Panel (WS-CDC-2500W) Terminal block cover DC power cable terminal block Power switch INP UT OUT PUT FAIL Status LEDs Captive installation screw Figure 4-13 DC-Input Wire Connections on the Terminal Block (WS-CDC-1300W) DC-input cable...
Page 160 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-14 DC-Input Wire Connections on the Terminal Block (WS-CDC-2500W) DC-input cable Power leads attached to terminal block ( - ) Negative (+) Positive ( ) Ground Power switch INP UT...
Page 161 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-15 Handling a DC-Input Power Supply WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT...
Page 162 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Installing a 1300 W or 2500 W DC-Input Power Supply Before performing any of the following procedures, ensure that power is removed from the DC Warning circuits. To ensure that all power is removed, locate the circuit breakers or fuses on the DC power lines that service the DC circuits.
Page 163 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Attach the appropriate lugs to the DC-input wires. The maximum width of a lug is 0.300 inch (7.6 mm). Step 7 The wire should be sized according to local and national installation requirements and electrical Note codes.
Page 164 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-16 DC-Input Power Supply Connectors (WS-CDC-1300W) DC-input cable Power leads attached to terminal block (+) Positive ( - ) Negative ( ) Ground Power switch INP UT OU TPU T FAI L DC-input power supply...
Page 165: Removing And Installing The 2700 W Dc-Input Power Supply
Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Removing and Installing the 2700 W DC-Input Power Supply This section covers the power supply removal and installation procedures for the 2700 W DC-input power supply and is divided into the following topics: Required Tools, page 4-25 •...
Page 166 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-18 DC-Input Front Panel for 2700-W DC-Input Power Supply P W R - 2 7 0 0 - D C IN P U T1 -V E -1 IN P U T2 FA N O U TP U...
Page 167 GA GE WE R SU PP LY If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco part number Step 8 700-03104-01) over the opening, and secure it with the captive installation screws.
Page 168 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-20 Handling the Power Supply P W R -2 7 0 0 -D C INP UT INP UT FA N OU TP UT 48 V-6 0V 48 V-6 0V FA IL =4 0A...
Page 169 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-22 DC-Input Front Panel for 2700-W DC-Input Power Supply P W R - 2 7 0 0 - D C IN P U T1 -V E -1 IN P U T2 FA N O U TP U...
Page 170 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Connect the DC-input wires to the 2700 W power supply terminal block (Figure 4-22) in this order: Step 7 Ground • Negative (-) • Positive (+) • Depending on which side you are connecting the DC-input wires, be sure that the DC-input wires rest in the appropriate cable holder.
Page 171: Removing And Installing A 4000 W Dc-Input Power Supply
Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Removing and Installing a 4000 W DC-Input Power Supply This section covers the power supply removal and installation procedures for the 4000 W DC-input power supply and is divided into the following topics: Required Tools, page 4-31 •...
Page 172 PWR-4000-DC power supply with an outer terminal block cover. An earlier Note version of this power supply does not have an outer terminal block cover. To order a retrofit kit containing this cover, use Cisco Systems part number CVR-4000DC-TERM=. Catalyst 6500 Series Switches Installation Guide 4-32...
Page 173 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Remove the two screws securing the outer terminal block cover, and remove the cover from the power Step 3 supply. (See Figure 4-24.) Remove the two screws securing the left inner terminal block cover, remove the cover, and set it aside. Step 4 Remove one screw securing the right inner terminal block cover, remove the cover, and set it aside.
Page 174 INPU T OK OUTP UT FAIL If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco part number Step 9 700-03104-01) over the opening, and secure it with the captive installation screws. Catalyst 6500 Series Switches Installation Guide...
Page 175 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Installing a 4000 W DC-Input Power Supply The 4000 W DC-input power supply can be wired for 2700 W or 4000 W operation. The type of installation that you are performing determines the number of power cables and how they are routed. Refer to Table 4-2 to select the appropriate installation procedure for your site.
Page 176 PWR-4000-DC power supply with an outer terminal block cover. An earlier Note version of this power supply does not have an outer terminal block cover. To order a retrofit kit containing this cover, use Cisco Systems part number CVR-4000DC-TERM=. Catalyst 6500 Series Switches Installation Guide 4-36...
Page 177 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Installing the 4000 W Power Supply (Wiring for 2700 W Operation; Left Power Bay) Refer to Figure 4-27 for item location and identification on the 4000 W DC-input power supply. You should allow a minimum of 2.5 to 3 inches (63.5 mm to 76.2 mm) of space between the side of the Note power supply and any obstructions (such as the side of an enclosed equipment rack).
Page 178 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Use both hands to install and remove the power supplies. Each DC-input power supply weighs 32 pounds Caution (14.5 kg). Step 4 Grasp the power supply handle with one hand, and place your other hand underneath the power supply. Slide the power supply into the power supply bay.
Page 179 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Wrap the large perforated flaps around each pair of conductors, inserting each locking tab into the rear Step 9 of the slot. Pull the tab until the cover is secured around the power cabling trim, and discard the excess tab plastic.
Page 180 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Position and secure the left and the right inner terminal block covers. Step 12 Secure outer terminal block cover. Step 13 If you are installing a second power supply operating at 2700 W in the right-side power supply bay, Step 14 proceed to “Installing the 4000 W Power Supply (Wiring for 2700 W Operation;...
Page 181 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies The power supply terminal block lug opening width is 0.62 inch (15.8 mm). The terminal posts are centered 0.63 inches (15.88 mm) apart and have a 1/4-20 thread. We recommend that you use an appropriately sized industry standard 2-hole, standard barrel compression lug.
Page 182 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Remove the two screws that secure the outer terminal block cover, and remove the cover from the power Step 6 supply. Remove the two screws that secure the left inner terminal block cover, remove the cover, and set it aside. Step 7 Remove the one screw that secures the right inner terminal block cover, remove the cover, and set it aside.
Page 183 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-33 DC-Input Wire Connections for 2700 W Operation (Right-Side Power Bay) Plastic insulator Power leads attached to terminal block Terminal (+) Positive block cover ( - ) Negative (+) Positive ( - ) Negative Power...
Page 184 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Installing the 4000 W Power Supply (Wiring for 4000 W Operation; Left Power Bay) Figure 4-27 for item location and identification on the 4000 W DC-input power supply. You should allow a minimum of 2.5 to 3 inches (63.5 mm to 76.2 mm) of space between the side of the Note power supply and any obstructions (such as the side of an enclosed equipment rack).
Page 185 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Grasp the power supply handle with one hand, and place your other hand underneath the power supply. Step 4 Slide the power supply into the power supply bay. Make sure that the power supply is fully seated in the bay.
Page 186 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies From the left side of the power supply, connect the DC-input wires to the left power supply terminal Step 10 block (Figure 4-36) in this order: Ground Negative (-) Positive (+) When you tighten the terminal nuts, make sure that they are snug.
Page 187 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Using the cable tie provided, place the cable tie through the slot at the top of the left terminal block cover, Step 12 and secure the wiring that connects to the right terminal block. Secure the outer block cover.
Page 188 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Prepare the source DC-input power cables by attaching the appropriately sized lugs. Step 3 The power supply terminal block lug opening width is 0.62 inch (15.8 mm). The terminal posts are centered 0.63 inches (15.88 mm) apart and have a 1/4-20 thread.
Page 189 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Tighten the power supply captive installation screws. Step 5 Remove the two screws that secure the outer terminal block cover, and remove the cover from the power Step 6 supply.
Page 190 Chapter 4 Removal and Replacement Procedures Removing and Installing the DC-Input Power Supplies Figure 4-39 DC-Input Wire Connections for 4000 W Operation (Right-Side Power Bay) Power leads attached to terminal block Power leads (+) Positive attached to ( - ) Negative Plastic Terminal terminal block...
Page 191: Removing And Installing The Power Entry Modules (Pems)
Chapter 4 Removal and Replacement Procedures Removing and Installing the Power Entry Modules (PEMs) Turn the power switch to the On (|) position on the power supply. Turning on the power switch also Step 16 engages a pawl that locks the power supply in the chassis. Verify the power supply operation by ensuring that the power supply front panel LEDs are in the Step 17 following states:...
Page 192: Required Tools
Figure 4-43, and slide it completely out of the chassis. If the PEM bay is to remain empty, install a blank PEM filler plate (Cisco part number 800-16719-01) Step 6 over the opening, and secure it with the captive installation screws.
Page 193: Installing The Ac-Input Pem
“Establishing the System Ground” section on page 3-22. If necessary, remove the blank PEM filler plate (Cisco part number 800-16719-01) from the chassis PEM Step 2 bay opening by loosening the captive installation screws. Retain the blank PEM filler plate for future use.
Page 194: Removing The Dc-Input Pem
Chapter 4 Removal and Replacement Procedures Removing and Installing the Power Entry Modules (PEMs) Plug the power cord into the PEM. (See Appendix A for a list of supported AC power cords.) Step 5 Connect the other end of the power cord to an AC-input power source. Step 6 In a system with dual power supplies, connect each power supply to a separate input source.
Page 195 Step 5 and slide the PEM completely out of the chassis. Set the PEM aside. If the PEM bay is to remain empty, install a blank PEM filler plate (Cisco part number 800-16719-01) Step 6 over the opening, and secure it with the captive installation screws.
Page 196: Installing The Dc-Input Pem
Chapter 4 Removal and Replacement Procedures Removing and Installing the Power Entry Modules (PEMs) Installing the DC-Input PEM Before performing any of the following procedures, ensure that power is removed from the Warning DC circuit. Statement 1003 Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.
Page 197: Removing And Installing The Fan Assembly
Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-47 DC-Input PEM Terminal Block Screws DC PEM 1 DC PEM 2 Cable clips DC PEM 1 terminal block screws WS-X6 K-SUP 2-2GE Switch Load CONSOL E 100% PORT MODE...
Page 198 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the Warning fan blades completely stop before you remove the fan tray. Statement 258 To remove the existing fan assembly, follow these steps: Locate the fan assembly as follows: Step 1...
Page 199 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-49 Fan Assembly: Catalyst 6503 and Catalyst 6503-E Switches WS-X6K -SUP2-2 GE Switch CONSOLE Load 100% PORT PORT 1 CONSOLE MODE SUPERV ISOR2 PORT 2 PCMCIA EJECT OSM-4OC1 2 POS-SI 4 PORT OC-12 POS SM OSM-4OC1 2 POS-SI...
Page 200 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-51 Fan Assembly: Catalyst 6506 and Catalyst 6506-E Switches WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 MODE PORT 2 CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load 100%...
Page 201 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-52 Fan Assembly: Catalyst 6509 and Catalyst 6509-E Switches WS-X6K-SUP2-2 GE Switch Load 100% CONSOLE PORT PORT 1 PORT 2 MODE CONSOLE SUPERVISOR2 PCMCIA EJECT WS-X6K-SUP2-2 GE Switch Load 100%...
Page 202 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-53 Fan Assembly: Catalyst 6509-NEB Switch Captive installation screw STATUS Captive installation screw INPUT OUTPUT FAIL INPUT OUTPUT FAIL Catalyst 6500 Series Switches Installation Guide 4-62 OL-5781-04...
Page 203 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-54 Fan Assembly: Catalyst 6509-NEB-A Switch assemblies Supervisor engine Redundant supervisor engine Slots 1-9 (right to left) POWE R SUPP LY 1 POWE R SUPP LY 2 INPUT OUTPUT FAIL...
Page 204 Chapter 4 Removal and Replacement Procedures Removing and Installing the Fan Assembly Figure 4-55 Accessing the Fan Trays on the Catalyst 6509-NEB-A Switch Captive installation screws STATU S Figure 4-56 Fan Assembly: Catalyst 6513 Switch WS-X6K-SUP2- 2GE Switch Load CONSOLE 100% PORT MODE...
Page 205: Installing The Fan Assembly
If after several attempts the fans do not operate or if you experience trouble with the installation (for Step 3 instance, if the captive installation screws do not align with the chassis holes), contact a Cisco customer service representative for assistance.
Page 206: Installing The Air Filter Assembly On A Catalyst 6509-Neb-A Switch (Optional)
Chapter 4 Removal and Replacement Procedures Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) This section describes how to install the optional air filter assembly for the Catalyst 6509-NEB-A switch.
Page 207 Chapter 4 Removal and Replacement Procedures Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) Figure 4-58 Installing the New Intake Panel INPUT OUTPU T FAIL INPUT OUTPU T FAIL Thumbscrews Fastening screw Support loop Remove the inner filter retainer from the filter cage assembly by depressing the thumb loops and Step 3 carefully sliding filter retainer outwards.
Page 208 Chapter 4 Removal and Replacement Procedures Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) Figure 4-59 Removing the Inner Filter Retainer Filter cage assembly Filter retainer Thumb loops Tabs Place the foam filter over the filter retainer. (See Figure 4-60.) Step 4...
Page 209 Chapter 4 Removal and Replacement Procedures Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) Figure 4-60 Placing the Foam Filter Over the Filter Retainer Filter cage assembly Filter Filter retainer Tabs Thumb loops Install the filter assembly with the tabs facing the floor, as follows: Step 6 Fit the tabs (see Figure...
Page 210 Chapter 4 Removal and Replacement Procedures Installing the Air Filter Assembly on a Catalyst 6509-NEB-A Switch (Optional) Figure 4-61 Installing the Filter Assembly INPUT OUTPU T FAIL INPUT OUTPU T FAIL Thumbscrews Fastening screw Notch Note We recommend that you change the air filters every three months. Catalyst 6500 Series Switches Installation Guide 4-70 OL-5781-04...
Page 211: Appendix
A P P E N D I X Power Supply Specifications This appendix provides specifications for the Catalyst 6500 series power supplies. Table A-1 lists the currently available Catalyst 6500 series switch power supplies and the power supply description location. Table A-1 Catalyst 6500 Series Power Supplies Power Supply...
Page 212: Power Supply Compatibility Matrix
Appendix A Power Supply Specifications Power Supply Compatibility Matrix The Catalyst 6500 series switches allow you to mix AC-input and DC-input power supplies in the same Note chassis. Many telco organizations require a –48 VDC power supply to accommodate their power distribution Note systems.
Page 213 Appendix A Power Supply Specifications Power Supply Compatibility Matrix Table A-2 Catalyst 6500 Series Switch Supported Power Supply Configurations (continued) Platform Supported Power Supplies Catalyst 6509-E 2500 W AC-input and DC-input • 3000 W AC-input • • 4000 W AC-input and DC-input •...
Page 214: 950 W Ac-Input And Dc-Input Power Supplies
Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies 950 W AC-Input and DC-Input Power Supplies The 950 W AC-input (PWR-950-AC) and DC-input (PWR-950-DC) power supplies can be installed in the Catalyst 6503 and Catalyst 6503-E switch chassis only. Due to form factor differences, the 950 W AC-input and DC-input power supplies cannot be installed in any other Catalyst 6500 series switch chassis.
Page 215: 950 W Power Supply Specifications
Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies Figure A-3 DC Power Entry Module (PEM) Catalyst 6503 DC PEM Captive installation screws 950 W Power Supply Specifications Table A-3 lists the specifications for the 950 W AC-input and DC-input power supplies. Table A-3 950 W AC-Input and DC-Input Power Supplies Specifications Item...
Page 216 Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies Table A-3 950 W AC-Input and DC-Input Power Supplies Specifications (continued) Item Specification Branch circuit requirement (AC-input) Each chassis power supply should have its own dedicated, fused-branch circuit: For North America—15 A •...
Page 217 Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies Table A-3 950 W AC-Input and DC-Input Power Supplies Specifications (continued) Item Specification Front panel LEDs • INPUT OK AC-input power supplies: Green—Source AC voltage is OK. (Input voltage •...
Page 218: 950 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 950 W AC-Input and DC-Input Power Supplies 950 W Power Supply AC Power Cords Table A-4 lists the 950 W AC-input power supply AC power cords specifications. These power cords plug into the 950 W PEM(PEM-15A-AC), not directly into the power supply. The table includes references to power cord illustrations.
Page 219: 1000 W Ac-Input Power Supply
Appendix A Power Supply Specifications 1000 W AC-Input Power Supply 1000 W AC-Input Power Supply The 1000 W AC-input power supply (WS-CAC-1000W) is supported in the following Catalyst 6500 series switches: Catalyst 6506 • Catalyst 6509 • Catalyst 6509-NEB • The 1000 W power supply (shown in Figure A-4) shares the same form factor as the 1300 W, 2500 W,...
Page 220: 1000 W Power Supply Specifications
Appendix A Power Supply Specifications 1000 W AC-Input Power Supply 1000 W Power Supply Specifications Table A-5 lists the specifications for the 1000 W AC-input power supply. Table A-5 1000 W Power Supply Specifications Specification Description AC-input type Autoranging input with power factor correction (PFC) Power factor correction is a standard feature on Note all Catalyst 6500 series AC-input power...
Page 221 Appendix A Power Supply Specifications 1000 W AC-Input Power Supply Table A-5 1000 W Power Supply Specifications (continued) Specification Description Power supply output capacity 1000 W Power supply output • 15 A @ +3.3 V 5 A @ +5 V •...
Page 222: 1000 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 1000 W AC-Input Power Supply 1000 W Power Supply AC Power Cords Table A-6 lists the specifications for the AC power cords that are available for the 1000 W AC-input power supply. The table includes references to power cord illustrations. All 1000 W power supply power cords are 8 feet 2 inches (2.5 meters) in length.
Page 223: 1300 W Ac-Input And Dc-Input Power Supplies
Appendix A Power Supply Specifications 1300 W AC-Input and DC-Input Power Supplies 1300 W AC-Input and DC-Input Power Supplies The 1300 W AC-input power supply (WS-CAC-1300W) and 1300 W DC-input power supply (WS-CDC-1300W) are supported in the following Catalyst 6500 series switches: Catalyst 6506 •...
Page 224: 1300 W Power Supply Specifications
Appendix A Power Supply Specifications 1300 W AC-Input and DC-Input Power Supplies 1300 W Power Supply Specifications Table A-7 lists the specifications for the 1300 W AC-input and DC-input power supplies. Table A-7 1300 W AC-Input and DC-Input Power Supplies Specifications Specification Description AC-input type...
Page 225 Appendix A Power Supply Specifications 1300 W AC-Input and DC-Input Power Supplies Table A-7 1300 W AC-Input and DC-Input Power Supplies Specifications (continued) Specification Description AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range) Power supply output capacity • 1300 W maximum (AC-input) 1360 W maximum (DC-input) •...
Page 226 Appendix A Power Supply Specifications 1300 W AC-Input and DC-Input Power Supplies Table A-7 1300 W AC-Input and DC-Input Power Supplies Specifications (continued) Specification Description Front panel LEDs • INPUT OK AC-input power supplies: Green—Source AC voltage is OK. (Input voltage •...
Page 227: 1300 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 1300 W AC-Input and DC-Input Power Supplies 1300 W Power Supply AC Power Cords Table A-8 lists the specifications for the AC power cords that are available for the 1300 W AC-input power supply. The table includes references to power cord illustrations. All 1300 W power supply power cords are 14 feet (4.3 meters) in length.
Page 228: 1400 W Ac-Input Power Supply
Appendix A Power Supply Specifications 1400 W AC-Input Power Supply 1400 W AC-Input Power Supply The 1400 W AC-input power supply (PWR-1400-AC) can be installed in the Catalyst 6503 switch and Catalyst 6503-E switch chassis only. Due to form factor differences, the 1400 W AC-input power supply cannot be installed in any other Catalyst 6500 series switch chassis.
Page 229: 1400 W Power Supply Specifications
Appendix A Power Supply Specifications 1400 W AC-Input Power Supply 1400 W Power Supply Specifications Table A-9 lists the specifications for the 1400 W AC-input power supply. Table A-9 1400 W Power Supply Specifications Specification Description AC-input type Autoranging input. Power Factor Correction (PFC) included.
Page 230: 1400 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 1400 W AC-Input Power Supply Table A-9 1400 W Power Supply Specifications (continued) Specification Description Output holdup time 20 ms minimum Heat Dissipation 1193 BTU/hour (approx.) Front panel LEDs INPUT OK Green—Source AC voltage is OK. (Input voltage •...
Page 231 Appendix A Power Supply Specifications 1400 W AC-Input Power Supply Table A-10 1400 W Power Supply AC Power Cords (continued) Power Cord Power Cord Reference Locale Part Number Source Plug Type Cordset Rating Illustration International CAB-AC-2500W-INT= IEC 309 16 A, 250 VAC Figure A-39 Israel CAB-AC-2500W-ISRL=...
Page 232: 2500 W Ac-Input And Dc-Input Power Supplies
Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies 2500 W AC-Input and DC-Input Power Supplies The 2500 W AC-input power supply (WS-CAC-2500W) and 2500 W DC-input power supply (WS-CDC-2500W) are supported in the following Catalyst 6500 series switches: Catalyst 6506 •...
Page 233: 2500 W Power Supply Specifications
Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies Figure A-10 2500 W DC-input Power Supply Terminal block cover INPU T OUT PUT FAIL Captive installation screw 2500 W Power Supply Specifications Table A-11 lists the specifications for the 2500 W AC-input and DC-input power supplies. Table A-11 2500 W Power Supply Specifications Specification Description...
Page 234 Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies Table A-11 2500 W Power Supply Specifications (continued) Specification Description Branch circuit requirement (AC-input) Each chassis power supply should have its own dedicated, fused-branch circuit: For North America—20 A •...
Page 235 Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies Table A-11 2500 W Power Supply Specifications (continued) Specification Description Power supply output (DC supply) 15 A @ +3.3 V • 5 A @ +5 V • • 10 A @ +12 V •...
Page 236 Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies Table A-11 2500 W Power Supply Specifications (continued) Specification Description Front panel LEDs • INPUT OK AC-input power supplies: Green—Source AC voltage is OK. (Input voltage • is 85 VAC or greater.) •...
Page 237: 2500 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 2500 W AC-Input and DC-Input Power Supplies 2500 W Power Supply AC Power Cords Table A-12 lists the specifications for the AC power cords that are available for the 2500 W AC-input power supply. The table includes references to power cord illustrations. All 2500 W power supply power cords are 14 feet (4.3 meters) in length.
Page 238: 2700 W Ac-Input And Dc-Input Power Supplies
Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies 2700 W AC-Input and DC-Input Power Supplies The 2700 W AC-input power supply (PWR-2700-AC/4) and 2700 W DC-input power supply (PWR-2700-DC/4) are supported only in the Catalyst 6504-E switch. See Figure A-11 for the 2700 W AC-input power supply and...
Page 239 Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies Figure A-12 2700 W DC-input Power Supply P W R - 2 7 0 0 - D C IN P U T1 -V E -1 IN P U T2 FA N O U TP U 48 V- 60...
Page 240: 2700 W Power Supply Specifications
Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies 2700 W Power Supply Specifications Table A-11 lists the specifications for the 2700 W AC-input and DC-input power supplies. Table A-13 2700 W Power Supply Specifications Specification Description AC-input type Autoranging input with power factor correction (PFC).
Page 241 Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies Table A-13 2700 W Power Supply Specifications (continued) Specification Description DC-input current (per DC input) 43 A @ –40.5 VDC • 37 A @ –48 VDC • • 29 A @ –60 VDC Power supply output (AC supply) 100/120 VAC operation...
Page 242 Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies Table A-13 2700 W Power Supply Specifications (continued) Specification Description Front panel LEDs • INPUT 1 OK AC-input power supplies: INPUT 2 OK (DC-Input power supply Green—Source AC voltage is OK. (Input voltage •...
Page 243: 2700 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 2700 W AC-Input and DC-Input Power Supplies 2700 W Power Supply AC Power Cords Table A-12 lists the specifications for the AC power cords that are available for the 2700 W AC-input power supply. The table includes references to power cord illustrations. All 2700 W power supply power cords are 14 feet (4.3 meters) in length.
Page 244: 3000 W Ac-Input Power Supply
Appendix A Power Supply Specifications 3000 W AC-Input Power Supply 3000 W AC-Input Power Supply The 3000 W AC-input power supply (WS-CAC-3000W) is supported in the following Catalyst 6500 series switches: Catalyst 6506 • Catalyst 6506-E • Catalyst 6509 • •...
Page 245: 3000 W Power Supply Specifications
Appendix A Power Supply Specifications 3000 W AC-Input Power Supply 3000 W Power Supply Specifications Table A-15 lists the specifications for the 3000 W AC-input power supply. Table A-15 3000 W Power Supply Specifications Specification Description AC-input type Autoranging input with power factor correction (PFC). Power factor correction is a standard feature on Note all Catalyst 6500 series AC-input power...
Page 246 Appendix A Power Supply Specifications 3000 W AC-Input Power Supply Table A-15 3000 W Power Supply Specifications (continued) Specification Description Power supply output 100/120 VAC operation • 25.0 A @ +3.3 V – – 5 A @ +5 V – 12 A @ +12 V 27.89 A @ +42 V –...
Page 247: 3000 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 3000 W AC-Input Power Supply 3000 W Power Supply AC Power Cords Table A-16 lists the specifications for the AC power cords that are available for the 3000 W AC-input power supply. The table includes references to power cord illustrations. All 3000 W power supply power cords are 14 feet (4.3 meters) in length.
Page 248: 4000 W Ac-Input And Dc-Input Power Supplies
Appendix A Power Supply Specifications 4000 W AC-Input and DC-Input Power Supplies 4000 W AC-Input and DC-Input Power Supplies The 4000 W AC-input and DC-input power supplies, (WS-CAC-4000W-US, WS-CAC-4000W-INT, and PWR-4000-DC) are supported in the following Catalyst 6500 series switches: Catalyst 6506 •...
Page 249: 4000 W Power Supply Specifications
Appendix A Power Supply Specifications 4000 W AC-Input and DC-Input Power Supplies Figure A-15 4000 W DC-Input Power Supply VE-1 VE-3 VE-1 VE-3 VE-2 VE-2 INP UT OK OUT PUT FAIL 4000 W Power Supply Specifications Table A-17 lists the specifications for the 4000 W AC-input and DC-input power supplies. Table A-17 4000 W AC-Input and DC-Input Power Supplies Specifications Specification Description...
Page 250 Appendix A Power Supply Specifications 4000 W AC-Input and DC-Input Power Supplies Table A-17 4000 W AC-Input and DC-Input Power Supplies Specifications (continued) Specification Description Branch circuit requirement (AC-input) Each chassis power supply should have its own dedicated, fused-branch circuit: For North America—30 A •...
Page 251 Appendix A Power Supply Specifications 4000 W AC-Input and DC-Input Power Supplies Table A-17 4000 W AC-Input and DC-Input Power Supplies Specifications (continued) Specification Description Power supply output (AC power supply) 15 A @ +3.3 V • 5 A @ +5 V •...
Page 252: 4000 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 4000 W AC-Input and DC-Input Power Supplies 4000 W Power Supply AC Power Cords Table A-18 lists the specifications for the AC power cords that are available for the 4000 W AC-input power supply. Included in the table are references to illustrations of the power cords. Table A-18 4000 W Power Supply AC Power Cords Power Cord Power Cord...
Page 253: 6000 W Ac-Input Power Supply
Appendix A Power Supply Specifications 6000 W AC-Input Power Supply 6000 W AC-Input Power Supply The 6000 W AC-input (WS-CAC-6000W) power supply is supported in the following Catalyst 6500 series switches: Catalyst 6506 • Catalyst 6506-E • Catalyst 6509 • •...
Page 254: 6000 W Power Supply Specifications
Appendix A Power Supply Specifications 6000 W AC-Input Power Supply 6000 W Power Supply Specifications Table A-19 lists the specifications for the 6000 W AC-input power supply. Table A-19 6000 W AC-Input Power Supply Specifications Specification Description AC-input type 2 AC-inputs per power supply. High-line input with power factor correction (PFC) included.
Page 255 Appendix A Power Supply Specifications 6000 W AC-Input Power Supply Table A-19 6000 W AC-Input Power Supply Specifications (continued) Specification Description System power dissipation 7034 W Branch circuit requirement (AC-input) Each power supply input should have its own dedicated, fused-branch circuit: •...
Page 256: 6000 W Power Supply Ac Power Cords
Appendix A Power Supply Specifications 6000 W AC-Input Power Supply Table A-19 6000 W AC-Input Power Supply Specifications (continued) Specification Description Front panel LEDs • INPUT OK 1 and INPUT OK 2 • Green—Source voltage is OK. (Input voltage is 85 VAC or greater.) •...
Page 257: Ac Power Cord Illustrations
Appendix A Power Supply Specifications AC Power Cord Illustrations Table A-20 6000 W Power Supply AC Power Cords (continued) Power Cord Power Cord Reference Locale Part Number Source Plug Type Cordset Rating Illustration Japan, North America CAB-AC-C6K-TWLK= NEMA L6-20 16 A, 250 VAC Figure A-41 (locking plug) 200–240VAC operation...
Page 258 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-18 CAB-AC10A-90L-EU= Cordset rating: 10 A, 250 V Length: 8 ft 2 in. (2.5 m) Plug: CEE 7/7 Connector: IEC 60320 C15 Figure A-19 CAB-AC10A-90L-IT= Cordset rating: 10 A, 250 V Length: 8 ft 2 in.
Page 259 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-21 CAB-AC10A-90L-UK= Cordset rating: 10 A, 250 V Length: 8 ft 2 in. (2.5 m) 13 A Plug: BS 1363 Connector: IEC 60320 C15 fuse Figure A-22 CAB-7KACR= Cordset rating: 10 A, 250 V Length: 8 ft 2 in.
Page 260 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-24 CAB-7KACE= Cordset rating: 16 A, 250 V Length: 8 ft 2 in. (2.5 m) Plug: CEE 7/7 Connector: IEC 60320 C15 Figure A-25 CAB-7KACI= Cordset rating: 10 A, 250 V Length: 8 ft 2 in.
Page 261 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-27 CAB-7KACU= Cordset rating: 10 A, 250 V fuse Length: 8 ft 2 in. (2.5 m) Plug: BS 1363 Connector: IEC 60320 C15 Figure A-28 CAB-7513ACR= Cordset rating: 10 A, 250 V Length: 14 ft 0 in.
Page 262 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-30 CAB-7513ACE= Cordset rating: 16 A, 250 V Length: 14 ft 0 in. (4.26 m) Plug: CEE 7/7 Connector: IEC 60320 C19 Figure A-31 CAB-AC-2500W-ISRL Cordset rating: 16 A, 250 V Length: 14 ft 0 in.
Page 263 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-33 CAB-7513AC= Cordset rating: 20 A, 125 V Plug: NEMA 5-20 Length: 14 ft 0 in. (4.26 m) Connector: IEC 60320 C19 Figure A-34 CAB-AC16A-CH= Cordset rating: 16A, 250V Length: 14 ft 0 in. (4.26 m) Plug: GB16C Connector: IEC 60320-1 C19...
Page 264 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-36 CAB-ACS-10= Cordset rating: 10 A, 250 V Length: 7 ft 0 in. (2.13 m) Plug: SEV 1011 Connector: IEC 60320 C19 Figure A-37 CAB-7513ACU Cordset rating: 13 A, 250 V Plug: BS 1363 Length: 14 ft 0 in.
Page 265 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-39 CAB-AC-2500W-INT= Cordset rating: 16 A, 250 V Length: 14 ft 0 in. (4.26 m) Plug: IEC 309 Connector: IEC 60320 C19 Figure A-40 CAB-AC-2500W-US1= Cordset rating: 16 A, 250 V Length: 14 ft 0 in.
Page 266 Appendix A Power Supply Specifications AC Power Cord Illustrations Figure A-42 CAB-ACS-16= Cordset rating: 16 A, 250 V Length: 8 ft 2 in. (2.5 m) Plug: SEV 5934-2 Type 23 Connector: IEC 60320 C19 Figure A-43 CAB-AC-16A-AUS= Cordset rating: 16 A, 250 V Length: 14 ft 0 in.
Page 267: Power Supply Redundancy
Appendix A Power Supply Specifications Power Supply Redundancy Figure A-45 WS-CAC-4000W-INT= Hardwired to Cordset rating: 32 A, 250 V power Length: 12 ft 0 in. (3.65 m) supply Plug: IEC 60309 Figure A-46 WS-CAC-4000W-US= Hardwired to Cordset rating: 30 A, 250 V power Length: 12 ft 0 in.
Page 268 If the difference is greater than 10%, the lesser wattage power supply is disabled. For Cisco IOS, both power supplies come on. The total available wattage is the output wattage of the higher wattage power supply. Equal or unequal...
Page 269 (Catalyst operating system). • For Cisco IOS, both power supplies come on. The total available wattage is the output wattage of the higher wattage power supply. Lower wattage power System log and syslog messages are generated.
Page 270 The lower-wattage supply is disabled (Catalyst operating system). • wattage installed and • For Cisco IOS, both power supplies come on. The total available redundancy enabled wattage is the output wattage of the higher wattage power supply. System is booted with •...
Page 271: Power Supply Redundancy
Appendix A Power Supply Specifications Power Supply Redundancy In systems that are equipped with two power supplies, if one power supply fails and the other power Note supply cannot fully power all of the installed modules, system power management will shut down devices in the following order: Power over Ethernet (PoE) devices—...
Page 272 Appendix A Power Supply Specifications Power Supply Redundancy Catalyst 6500 Series Switches Installation Guide A-62 OL-5781-04...
Page 273: Appendix
A P P E N D I X Transceivers, Module Connectors, and Cable Specifications This chapter describes the transceivers, connectors, and cables used with the Catalyst 6500 series switches. The chapter is divided into these sections: Transceivers, page B-1 • •...
Page 274: Transceivers
Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers 100-MB Transceiver Modules The 100-MB SFP transceiver modules are listed and described in Table B-1. See Figure B-1 for a view of the 100-MB SFP transceiver module. Table B-1 100-MB Transceiver Modules Descriptions Transceiver Type Product Number...
Page 275: 1-Gb Transceiver Modules
Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers 1-GB Transceiver Modules Table B-2 lists along with brief descriptions of the transceiver modules, pointers to cabling distances tables, and reference illustrations. Table B-2 1-GB Transceiver Modules Descriptions Transceiver Type Product Number Description GBIC WS-G5483=...
Page 276 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Table B-2 1-GB Transceiver Modules Descriptions (continued) Transceiver Type Product Number Description GLC-LH-SM= 1000BASE-LX/LH SFP transceiver module for SMF, • 1300-nm wavelength, • LC duplex connector. (See Figure B-5.) • Transceiver cabling information is contained in Table B-4.
Page 277 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Table B-3 GBIC Transceiver Module Cabling Specifications Wavelength Core Size Modal Bandwidth GBIC Connector (nm) Cable Type (micron) (MHz km) Cable Distance 1000BASE-T RJ-45 — — — 328 ft (100 m) (WS-G5483) 1000BASE-SX SC duplex...
Page 278 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Table B-4 SFP Transceiver Module Cabling Specifications Modal Wavelength Core Size Bandwidth SFP Module Connector (nm) Fiber Type (micron) (MHz/km) Cable Distance 1000BASE-T RJ-45 — Category 5, — — 328 ft (100 m) (GLC-T=) 5e, or 6 UTP/FTP...
Page 279 Figure B-5 1000BASE-X SFP Transceiver Modules (GLC-SX-MM, GLC-LH-SM, and GLC-ZX-SM) You can use any combination of SFP modules that your Cisco device supports. The only restrictions are Note that each SFP port must match the wavelength specifications on the other end of the cable and that the cable must not exceed the stipulated cable length for reliable communications.
Page 280: 10-Gb Transceiver Modules
Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers 10-GB Transceiver Modules The 10-GB transceiver modules are listed in Table B-5 along with brief descriptions of the transceiver modules, pointers to cabling distances tables, and reference illustrations. Table B-5 10-GB Transceiver Modules Transceiver Type Product Number...
Page 281 1. Minimum cabling distance for all types is 2 m according to the IEEE 802.3ae standard. 2. Requires a 5 db 1550 nm fixed loss attenuator for cable distances less than 20 km. The attenuator is available from Cisco Systems...
Page 282: Wdm Transceiver Modules
Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Figure B-6 10-Gigabit XENPACK Transceiver Module Captive installation screw Dust plug Transmit optical bore Receive optical bore WDM Transceiver Modules The WDM transceiver modules are listed in Table B-7 along with brief descriptions of the transceiver modules and reference illustrations.
Page 283: Wdm Transceiver Modules
CWDM or DWDM transport network; there is no transmitter in the GBIC. • The receiver can be used for all wavelengths supported by Cisco CWDM and DWDM transceivers and can be used interchangeably with 1000BASE-SX, 1000BASE-LX/LH, and 1000BASE-ZX transceivers on a port-by-port basis.
Page 284 Transceiver CWDM or DWDM transport network; there is no transmitter in the XENPAK. The receiver can be used for all wavelengths supported by Cisco • DWDM XENPAK transceivers. The W/O WDM receiver has a single SC connector.
Page 285 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Figure B-7 CWDM GBIC Transceiver Color arrow on label Optical bore dust plug Alignment groove Receive optical bore Spring clip Color dot Transmit optical bore Table B-9 DWDM GBIC Transceiver Module Product Numbers and ITU Channel Numbers DWDM GBIC Product Number Description...
Page 286 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Table B-9 DWDM GBIC Transceiver Module Product Numbers and ITU Channel Numbers (continued) DWDM GBIC Product Number Description ITU Channel DWDM-GBIC-42.94 1000BASE-DWDM 1542.94 nm GBIC DWDM-GBIC-42.14 1000BASE-DWDM 1542.14 nm GBIC DWDM-GBIC-40.56 1000BASE-DWDM 1540.56 nm GBIC DWDM-GBIC-39.77 1000BASE-DWDM 1539.77 nm GBIC...
Page 287 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Figure B-9 CWDM SFP Transceiver Color arrow on label Dustplug Receive optical bore Transmit optical bore Bail clasp Table B-11 DWDM XENPAK Transceiver Module Product Numbers and ITU Channel Numbers DWDM XENPAK Product Number Description ITU Channel...
Page 288 Appendix B Transceivers, Module Connectors, and Cable Specifications Transceivers Table B-11 DWDM XENPAK Transceiver Module Product Numbers and ITU Channel Numbers (continued) DWDM XENPAK Product Number Description ITU Channel DWDM-XENPAK-47.72 1000BASE-DWDM 1547.72 nm XENPAK DWDM-XENPAK-46.92 1000BASE-DWDM 1546.92 nm XENPAK DWDM-XENPAK-46.12 1000BASE-DWDM 1546.12 nm XENPAK DWDM-XENPAK-44.53...
Page 289: Module Connectors
Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors Figure B-10 DWDM XENPAK Transceiver Module Captive installation screw Dustplug Transmit optical bore Receive optical bore Module Connectors This section covers the types of module connectors used with the Catalyst 6500 series switches: RJ-45 Connector, page B-17 •...
Page 290: "Rj-21 Connector
Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors Figure B-11 RJ-45 Interface Cable Connector RJ-45 (both ends) Pin 1 Pin 8 Category 5e and Category 6 cables can store large levels of static electricity because of the dielectric Caution properties of the materials used in their construction.
Page 291 Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors Figure B-12 RJ-21 Telco Interface Cable Connectors RJ-21 port RJ-21 connector RJ-21 connector RJ-21 connector Table B-12 lists the output signals for the RJ-21 telco connector. The receive and transmit signals are polarized.
Page 292 Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors Table B-12 RJ-21 Connector Pinout Ethernet Port Connector Pin Connector Pin Signal Signal RxD (–) RxD (+) TxD (–) TxD (+) RxD (–) RxD (+) TxD (–) TxD (+) RxD (–) RxD (+) TxD (–) TxD (+)
Page 293: Connector (Ws-X6624-Fxs Only
Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors RJ-21 Connector (WS-X6624-FXS Only) The pinout for the RJ-21 connector on the 24-port WS-X6624-FXS analog interface module is shown in Table B-13. Table B-13 RJ-21 Connector Pinout (WS-X6224-FXS Analog Interface Module Only) Port Connector Pin Port...
Page 294: Sc Connector
Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors SC Connector The SC connector, shown in Figure B-13, is used to connect fiber-optic module ports or transceivers with the external SMF or MMF network. Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments.
Page 295: Lc Connector
Appendix B Transceivers, Module Connectors, and Cable Specifications Module Connectors Make sure that the optical connectors are clean before making the connections. Contaminated connectors Note can damage the fiber and cause data errors. For information on cleaning the optical connectors, see the “Cleaning the Fiber Optic Connectors”...
Page 296: Cables
Appendix B Transceivers, Module Connectors, and Cable Specifications Cables Cables Table B-14 lists the connector pinouts and signal names for a 10/100BASE-T crossover (MDI-X) cable. Figure B-16 shows a schematic of the 10/100BASE-T crossover cable. Table B-15 lists the connector pinouts and signal names for a 1000BASE-T crossover (MDI-X) cable.
Page 297: Cables B
Appendix B Transceivers, Module Connectors, and Cable Specifications Cables Table B-15 1000BASE-T Crossover Cable Pinout (MDI-X) Side 1 Pin (Signal) Side 2 Pin (Signal) 1 (TP0+) 3 (TP1+) 2 (TP0–) 6 (TP1–) 3 (TP1+) 1 (TP0+) 6 (TP1–) 2 (TP1–) 4 (TP2+) 7 (TP3+) 5 (TP2–)
Page 298: Console Port Mode Switch
B-18.) If your cable was purchased from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white on the other. (A rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5.)
Page 299: Console Port Mode 1 Signaling And Pinouts
Appendix B Transceivers, Module Connectors, and Cable Specifications Cables Console Port Mode 1 Signaling and Pinouts This section provides the signaling and pinouts for the console port in mode 1. (The port mode switch is in the in position.) DB-9 Adapter (for Connecting to a PC) Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-9 female DTE adapter (labeled “Terminal”) to connect the console port to a PC running terminal emulation software.
Page 300: Modem Adapter
Appendix B Transceivers, Module Connectors, and Cable Specifications Cables Table B-17 Port Mode 1 Signaling and Pinouts (DB-25 Adapter) (continued) RJ-45-to-DB-25 Terminal Console Console Port RJ-45-to-RJ-45 Rollover Cable Adapter Device Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal 1. Pin 1 is connected internally to Pin 8. Modem Adapter Use the RJ-45-to-RJ-45 rollover cable and the RJ-45-to-DB-25 male DCE adapter (labeled “Modem”) to connect the console port to a modem.
Page 301: Mode-Conditioning Patch Cord
When using the long wavelength/long-haul (LX/LH) GBIC with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the multimode fiber (MMF) cable on both the transmit and receive ends of the link. The 9.8 foot (3 meter) patch cord is required for link distances greater than 984 feet (300 meters).
Page 302: Differential Mode Delay
Appendix B Transceivers, Module Connectors, and Cable Specifications Cables Patch Cord Installation Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments. Statement 1051 Plug the end of the patch cord labeled “To Equipment” into the GBIC. (See Figure B-20.) Plug the end labeled “To Cable Plant”...
Page 303: Cleaning The Fiber Optic Connectors
Appendix B Transceivers, Module Connectors, and Cable Specifications Cleaning the Fiber Optic Connectors Figure B-21 LED Transmission Compared to Laser Transmission LED transmission Laser transmission Laser Lasers launch light in a more concentrated fashion. A laser transmitter couples light into only a fraction of the existing modes or optical pathways present in the fiber-optic cable.
Page 304 Appendix B Transceivers, Module Connectors, and Cable Specifications Cleaning the Fiber Optic Connectors The connection quality depends on two factors: the type of connector and the proper cleaning and connection techniques. Dirty fiber connectors are a common source of light loss. Keep the connectors clean at all times, and keep the dust covers installed when the connectors are not in use.
Page 305: Appendix
A P P E N D I X Repacking the Switch If you need to return or move the Catalyst 6500 series switch chassis, follow these steps to repack the switch using the original packaging material: Step 1 Set the chassis in the bottom pallet. (See Figure C-1.) Place the packing bag over the chassis.
Page 306 Appendix C Repacking the Switch Figure C-1 Packing Material Docs and accessories go in here packing material Power supply(s) go in here Figure C-2 Final Package Do not use tape to hold the outside carton to the bottom pallet. Packing straps must be added to hold the Note entire package together and to add strength to the package.
Page 307: Appendix
A P P E N D I X Chassis and Module Power and Heat Values This appendix provides the power and heat numbers for the Catalyst 6500 series chassis and modules. Chassis and fan trays—Table D-1 • • phones—Table D-2 Supervisor Engine—Table D-3 •...
Page 308 Module Power Power Heat Diss. Power Heat Diss. Module Type Current (A) (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) Cisco IP Phone 7960 0.15 7.88 26.89 8.47 28.92 Cisco IP Phone 7940 0.15 7.88 26.89 8.47 28.92 Cisco IP Phone 7910 0.13 5.46...
Page 309 Appendix D Chassis and Module Power and Heat Values Table D-3 Power Requirements and Heat Dissipation—Supervisor Engines Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-X6K-SUP1A-2GE...
Page 310 Appendix D Chassis and Module Power and Heat Values Table D-3 Power Requirements and Heat Dissipation—Supervisor Engines (continued) WS-SUP720-3BXL 7.82 328.44 410.55 1402.03 441.45 1507.56 Supervisor Engine 720 with PFC3BXL daughter card and integrated MSFC3 and switch fabric WS-F6K-PFC3A 2.25 94.50 118.13 403.40...
Page 311 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-F6700-DFC3C...
Page 312 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-X6148A-GE-45AF...
Page 313 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-X6196-21AF...
Page 314 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-X6416-GE-MT...
Page 315 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-X6704-10GE...
Page 316 Appendix D Chassis and Module Power and Heat Values Table D-4 Power Requirements and Heat Dissipation—Modules (continued) Module Module AC-Input DC-Input Model Number/ Current (A) Power Power Heat Diss. Power Heat Diss. Module Type @ 42 VDC (Watts) (Watts) (BTU/HR) (Watts) (BTU/HR) WS-SVC-CMM...
Page 317: Appendix
A P P E N D I X Troubleshooting The information in this chapter applies to all Catalyst 6500 series switches (Catalyst 6503, Note Catalyst 6503-E, Catalyst 6504-E, Catalyst 6506, Catalyst 6506-E, Catalyst 6509, Catalyst 6509-E, Catalyst 6509-NEB, Catalyst 6509-NEB-A, and Catalyst 6513) unless otherwise noted. This chapter describes how to troubleshoot the Catalyst 6500 series switch hardware installation and contains these sections: Getting Started, page E-1...
Page 318: Solving Problems At The System Component Level
Configuration Guide, the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide, the Catalyst 6500 Series Switch Command Reference, or the Catalyst 6500 Series Switch Cisco IOS Command Reference. Also, refer to your software release notes for hardware support information and software caveats.
Page 319: Identifying Startup Problems
If you have a redundant supervisor engine, refer to the Catalyst 6500 Series Switch Software Configuration Guide or the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide publications for descriptions of how the redundant supervisor engine comes online and how the software images are handled.
Page 320: Troubleshooting The Power Supply
Appendix E Troubleshooting Troubleshooting the Power Supply Troubleshooting the Power Supply If the INPUT OK LED does not light after you turn on the power switch, follow these steps to isolate a power subsystem problem: Verify that the INPUT OK LED on the power supply is green. Step 1 If the INPUT OK LED is green, the AC or DC source is good and the power supply is functional.
Page 321: Troubleshooting The Fan Assembly
Appendix E Troubleshooting Troubleshooting the Fan Assembly Troubleshooting the Fan Assembly To isolate a fan assembly problem, follow these steps: Verify that the FAN LED on the fan assembly is green. Step 1 If the FAN LED is not green, see the “Solving Problems at the System Component Level”...
Page 322 Refer to the Catalyst 6500 Series Switch Software Configuration Guide, the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide, the Catalyst 6500 Series Switch Command Reference, or the Catalyst 6500 Series Switch Cisco IOS Command Reference publications to configure or enable the interfaces.
Page 323: Contacting Customer Service
Appendix E Troubleshooting Contacting Customer Service Contacting Customer Service If you are unable to solve a startup problem after using the troubleshooting suggestions in this chapter, contact a customer service representative for assistance and additional instructions. Before you call, have the following information ready to help your service provider assist you as quickly as possible: Date you received the switch •...
Page 324 Appendix E Troubleshooting Contacting Customer Service Catalyst 6500 Series Switches Installation Guide OL-5781-04...
Page 325: I N D E X
I N D E X 2500 W AC-input power supplies Numerics AC power cords A-24 950 W AC-input power supplies form factor (figure) A-19 AC power cords overview A-19 form factor (figure) specifications A-21 overview 2500 W DC-input power supplies removing and installing 4-2, 4-9 form factor (figure)
Page 326 Index 4000 W DC-input power supplies source circuit requirements 2-17 form factor (figure) troubleshooting A-35 installing weight (caution) 4-37 4-10 overview acoustic noise A-34 specifications Catalyst 6503 switches A-35 6000 W AC-input power supplies Catalyst 6503-E switches 1-10 AC power cords A-42 Catalyst 6504-E switches 1-14...
Page 327 Index Catalyst 6509-NEB (figure) airflow (figure) 2-14 Catalyst 6509-NEB switches chassis, dimensions 1-41 Catalyst 6509-NEB-A (figure) environmental specifications 2-15 Catalyst 6509-NEB-A switches fan trays 1-46 Catalyst 6513 (figure) features table 2-16 Catalyst 6513 switches form factor (figure) 1-51 1-6, 1-7 chassis requirements (table) installing L brackets description...
Page 328 Index Catalyst 6504-E switches power supplies 1-23 acoustic noise shock and vibration specifications 1-14 1-24 airflow specifications 1-14 1-22 airflow (figure) supervisor engines 2-10 1-22 chassis, dimensions Catalyst 6509 switches 1-14 environmental specifications acoustic noise 1-13 1-29 fan trays 1-13 airflow 1-30 features table...
Page 329 Index features table physical characteristics 1-37 1-51 form factor (figure) power supplies 1-42 1-49 installing L brackets and cable guides shock and vibration specifications 3-10 1-50 installing the stabilizer kit specifications 3-15 1-48 physical characteristics supervisor engines 1-41 1-48 power supplies category 5e static electricity caution 1-39 2-18, B-18, B-19...
Page 330 Index CWDM GBICs documentation description audience B-10 CWDM SFPs conventions product numbers and color codes B-14 feedback obtaining additional information xxiii obtaining documentation ordering DB-9 adapters organization console port mode 1 B-27 product security overview DC-input power supplies related connecting system ground 3-22 DWDM GBICs figure...
Page 331 Index grounding. See system ground guidelines, rack-mounting the switch fan assemblies checking the installation 4-65 fan status LED 2-9, E-5 fan tray removal warning 4-58 IEEE 802.3z B-30 installing 4-65 installing troubleshooting patch cords B-30 fan tray removal warning 4-58 shelf brackets features installing the switch...
Page 332 Index Catalyst 6509-E switches 1-35 Catalyst 6509 switches 1-30 modem adapters B-28 Catalyst 6509-NEB switches 1-41 modes Catalyst 6509-NEB-A switches 1-46 fiber B-30 Catalyst 6513 switches 1-51 modules port mode switches LEDs mode 1 B-27 status LED mode 2 B-28 troubleshooting using B-26...
Page 333 Index Catalyst 6509 switches rollover cables 1-28 Catalyst 6509-E switches figure 1-33 B-26 Catalyst 6509-NEB switches identifying colors 1-39 B-26 Catalyst 6509-NEB-A switches 1-44 Catalyst 6513 switches 1-49 chassis compatibility matrix DC power cable leads color coding 2-18 SC connectors mixing AC-input and DC-input in the same chassis description B-22...
Page 334 Index site preparation system ground checklist accessory kit 2-19 3-21 Site Preparation and Safety Guide Catalyst 6503 connector location (figure) 3-23 site requirements Catalyst 6503-E connector location (figure) 3-23 airflow Catalyst 6504-E connector location (figure) 3-23 altitude Catalyst 6506 connector location (figure) 3-24 corrosion Catalyst 6506-E connector location (figure)
Page 335 Index DWDM XENPAK (figure) B-17 DWDM XENPAK descriptions B-12 warnings DWDM XENPAK product numbers and ITU channel numbers B-15 conventions GBIC cabling specifications translations GBICs warning definition GBICs (figure) WDM transceivers B-10 optical GBICs CWDM GBIC (figure) B-13 optical SFPs CWDM SFP (figure) B-15 R/O WDM GBIC...
Page 336 Index product numbers and ITU channel numbers B-15 R/O WDM descriptions B-12 specifications and cabling distances Catalyst 6500 Series Switches Installation Guide IN-12 OL-5781-04...

This manual is also suitable for:

Ws-c6506 Catalyst 6500 series

Cisco 6509 - Catalyst Chassis Switch Installation Manual

Preface

Product Overview

Chapter 2 Preparing for Installation

Chapter 3 Installing the Switch

Unpacking the Switch

Installing the Rack-Mount Kit

Installing the Switch Chassis in the Rack

Installing the Stabilizer Kit

Installing the Cable Management System (Catalyst 6509-NEB-A Switch Only)

Establishing the System Ground

Installing the Power Supplies in the Switch Chassis

Attaching the Interface Cables

Verifying Switch Chassis Installation

Chapter 4 Removal and Replacement Procedures

Appendix

Power Supply Specifications

Appendix A Power Supply Specification

Appendix

Transceivers, Module Connectors, and Cable Specifications

Cables

Appendix

Repacking the Switch

Appendix

Chassis and Module Power and Heat Values

Appendix

Troubleshooting

Solving Problems at the System Component Level

Identifying Startup Problems

Troubleshooting the Power Supply

Troubleshooting the Fan Assembly

Troubleshooting Modules

Contacting Customer Service

I N D E X

Quick Links

Troubleshooting

Related Manuals for Cisco 6509 - Catalyst Chassis Switch

Summary of Contents for Cisco 6509 - Catalyst Chassis Switch