IBM 2158240 - Aptiva E - 2158 Maintenance And Service Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Desktop
  5. 2158240 - Aptiva E - 2158
  6. Maintenance and service manual

IBM 2158240 - Aptiva E - 2158 Maintenance And Service Manual

Hardware maintenance manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Hardware Maintenance Service
for Service Level A
Machine Types 2158 and 2163 and
IBM Monitors 2235, 2236 and 2237
2158/2163
2235/2236/2237

Advertisement

Table of Contents
loading

Related Manuals for IBM 2158240 - Aptiva E - 2158

Summary of Contents for IBM 2158240 - Aptiva E - 2158

  • Page 1 Hardware Maintenance Service for Service Level A Machine Types 2158 and 2163 and IBM Monitors 2235, 2236 and 2237 2158/2163 2235/2236/2237...
  • Page 2 IBM may make improvements and/or changes in the product(s) and/ or the program(s) at any time. Address comments about this publication to IBM Corporation, Dept. E23/962-2, 455 Park Place, Lexington, KY 40511-1856, USA.

  • Page 3: Table Of Contents

    Contents Contents ......................I Notices ......................I Safety Information ....................II Laser Compliance Statement ..............XXIV Trademarks ....................XXV Preface .......................XXVI General Information ..................1 Introduction ......................2 Product Overview .....................2 Processors (Machine Type 2158) ..............2 Processors (Machine Type 2163) ..............2 Memory ......................3 External Ports.....................3 Diskette Drive.....................3 Hard Disk Drive ..................4 CD/DVD-ROM Drive ..................4 Multimedia....................4...
  • Page 4 Dimension (width x depth x height) ............23 Weight ......................23 Environment .....................23 Power consumption..................23 Electrical input..................24 Operating Requirements ................24 Special Tools ....................24 Check Procedures ..................25 Introduction ....................26 Start .......................27 Index of Symptoms, Messages, Error Codes, or Beeps ........31 Troubleshooting .....................47 Factory-Installed Storage Devices ............47 Factory-Installed Modem Card ...............50 Audio (Not Supported by Diagnostics Program) ..........
  • Page 5 Adapter Cards ..................84 Memory(DIMM) ..................85 AMD-K6 Processor (for 2158)..............86 Pentium II Processor Module (for 2163) ..........88 Celeron Processor Module (for 2163) ............93 System Backup Battery................99 Indicator LED and Cable ................100 System Board..................101 Handling ESD-Sensitive Parts ..............103 Software Recovery Procedure ..............104 Parts/Test Point Locations ................105 Introduction ....................106 Machine Type 2158 System Board Jumpers and Connectors ....
  • Page 6 Assembly 3: Machine Type 2158/2163 CD/DVD-ROM Drive ...... 139 Assembly 4: Machine Type 2158/2163 Monitor and Power Cord ....141 Assembly 5: Machine Type 2158/2163 Keyboard and Mouse .....142 Assembly 6: Machine Type 2158/2163 Zip Drive and Network Adapter ..143 Assembly 7: Machine Type 2158/2163 Software .........144 Appendix B.

  • Page 7: Notices

    Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM's product, program, or service may be used.

  • Page 8: Safety Information

    4. Remove all cables from devices. 5. Turn device ON CAUTION: When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer.
  • Page 9 • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. CAUTION: When a CD-ROM drive is installed, note the following. Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. Removing the covers of the CD-ROM drive could result in exposure to hazardous laser radiation.
  • Page 10 5.LIGUE o dispositivo CUIDADO: Ao substituir a bateria, utilize apenas o Número de Peça IBM 33F8354 ou um tipo de bateria equivalente recomendado pelo fabricante. Se seu sistema possuir um módulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de módulo, produzido pelo mesmo fabricante.
  • Page 11 Descarte a bateria conforme requerido pelas disposições e regulamentações locais. CUIDADO: Quando uma unidade de CD-ROM estiver instalada, observe o seguinte. A utilização de controles ou ajustes ou a execução de procedimentos diferentes daqueles especificados nesta publicação pode resultar em exposição perigosa à...
  • Page 13 Notices...
  • Page 14 VIII...
  • Page 15 Notices...
  • Page 17 4. Débranchez tous les câbles des 5. Mettez les unités sous tension. unités. ATTENTION: Remplacez la pile usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le Notices...
  • Page 18 fabricant. Si votre système est doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant. La pile contient du lithium et présente donc un risque d'explosion en cas de mauvaise manipulation ou utilisation. •...
  • Page 19 modems (sauf instruction contraire mentionnée dans les procédures d'installation et de configuration) VORSICHT: Aus Sicherheitsgründen bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. Aus Sicherheitsgründen: • Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen.
  • Page 20 Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung...
  • Page 21 ACHTUNG: An Netz-, Telefon- und Datenleitungen können gefährliche elektrische Spannungen anliegen. Um eine Gefährdung des Benutzers oder Beschädigung des Geräts zu vermeiden, ist der Server auszuschalten. Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Servergehäuses zu unterbrechen (sofern in Installations- und Konfigurationsanweisungen nicht anders angegeben) PERICOLO:...
  • Page 22 5.ACCENDERE le unità. ATTENZIONE: Quando si sostituisce la batteria, utilizzare solo una batteria IBM o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore.
  • Page 23 ATTENZIONE: Quando è installata un'unità CD-ROM, notare quanto segue: L'utilizzo di controlli, regolazioni o l'esecuzione di procedure non descritti nel presente manuale possono provocare l'esposizione a radiazioni pericolose. L'apertura di un'unità CD-ROM può determinare l'esposizione a radiazioni laser pericolose. All'interno dell'unità CD-ROM non vi sono parti su cui effettuare l'assistenza tecnica.
  • Page 24 XVIII...
  • Page 25 Notices...
  • Page 27 PELIGRO: Para evitar una posible descarga eléctrica, no conecte ni desconecte los cables ni lleve a cabo ninguna operación de instalación, de mantenimiento o de reconfiguración de este producto durante una tormenta eléctrica. Para evitar una posible descarga: • El cable de alimentación debe conectarse a un receptáculo con una instalación eléctrica correcta y con toma de tierra.
  • Page 28 CAUTION: Al cambiar la batería, utilice únicamente la batería IBM Número de pieza 33F8354 o un tipo de batería equivalente recomendado por el fabricante. Si el sistema tiene un módulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de módulo del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
  • Page 29 CAUTION: La corriente eléctrica de los cables de comunicaciones, de teléfono y de alimentación puede resultar peligrosa. Para evitar posibles lesiones o daños del aparato, desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems antes de abrir las cubiertas del servidor, salvo que se indique lo contrario en las instrucciones de las operaciones de instalación y configuración.

  • Page 30: Laser Compliance Statement

    Laser Compliance Statement The CD/DVD-ROM drive in the computer is a laser product. The CD/DVD- ROM drive's classification label (sample shown below) is located on the drive. CLASS 1 LASER PRODUCT APPAREIL A LASER CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 The CD/DVD-ROM drive is certified in the U.S.

  • Page 31: Trademarks

    Trademarks The following are trademarks of the IBM Corporation in the United States or other countries or both: Aptiva HelpCenter Operating System/2 OS/2 Personal System/2 PS/1 PS/2 Intel, Pentium, MMX, EtherExpress, and LANDesk are trademarks or registered trademarks of Intel Corporation.

  • Page 32: Preface

    Preface This manual contains service information for the 2158/2163 Service Level A (SL-A) model of the IBM Aptiva Personal Computer, worldwide. This manual is intended to be used as a stand-alone document to service Aptiva machine type 2158/2163 products. It is divided into the following chapters: Notices contains important safety information and notices required to service this computer.

  • Page 33: General Information

    Disk Drives ....................14 Input/Output Ports ..................16 Power Management .................17 Startup Options ..................18 Advanced Options..................19 Specifications ....................23 Dimension (width x depth x height) ............23 Weight ......................23 Environment .....................23 Power consumption..................23 Electrical input..................24 Operating Requirements ................24 Special Tools ....................24 Copyright IBM Corp. 1998...

  • Page 34: Introduction

    Introduction This chapter gives a general overview of the Aptiva Machine Type 2158/2163, describes the standard and optional features, and details functional and environmental specifications. Product Overview Machine Type 2158 and 2163 both have two PCI slots and one PCI/ISA shared slot.

  • Page 35: Memory

    Celeron • Includes Intel MMX™ media enhancement technology. • Offers Dynamic Execution technology. • Processor is provided in the Single Edge Processor Package (S.E.P.P.) with out L2 cache and fits into the slot 1. • One of the following processors can be installed: - Celeron 366 Mendocino - Celeron 400 Mendocino Memory...

  • Page 36: Hard Disk Drive

    • 3.5-in. 1.44 MB slimline diskette drive. Hard Disk Drive • 3.5-in., 1-in. height or 5.25-in, 1-in. height IDE AT drive. (3.5-in may be in acoustic mounting bracket) • 128 KB “look-ahead” cache memory in hard disk drive. • Average and minimum 12 ms seek time, access time varies for the hard disk drive and the hard disk drive manufacturer.

  • Page 37: Modem

    • One 3-pin (3-wire) cable for power light-emitting diode (LED). • One 2-pin (2-wire) cable for power switch. • One 4-pin modem voice-in/speaker-out cable. Modem • 56.6 Kbps PCI modem adapter card with data/fax/voice or non-voice features. • Telephone line-out (RJ-11) connector. •...

  • Page 38: Mouse

    Three PCI (Peripheral Component Interconnect) v2.1 compatible expansion slots that operates at 33 MHz bus speed. One IBM AT-ISA Plug and Play compatible expansion slot that operates at 8 MHz bus speed. Note: There is 1 PCI/ISA shared slot Hard disk drives Two PCI local bus Enhanced IDE v1.0 compatible hard disk...

  • Page 39: Cmos Reset

    Item- Interface Parallel port Supports SPP (IBM PC/XT, PC/AT, PS/2) compatible, EPP (IEEE 1284 compliance), ECP (IEEE 1284 compliance) interface. IEEE 1284 compliant Game port Game port interface for joystick. It also supports MIDI. Supports Universal HCI Specification for USB 1.0 CMOS Reset This system does not deny access to BIOS Setup Utility.

  • Page 40: Power-On Password

    Power-On Password A power-on password denies access to the system by an unauthorized user when the system is powered on. When a power-on password is active, the password prompt appears on the screen each time the system is powered on. The system starts after the proper password is entered.

  • Page 41: Flash (Bios) Update Procedure

    Flash (BIOS) Update Procedure NOTE: The flash update procedure does not change the model number and serial number information in BIOS. 1. Prepare a bootable DOS diskette disk with AFLASH.EXE, MSG.DAT, VXXYYZZ.RN and VXXYYZZ.BIN files NOTE: The AFLASH.EXE and MSG.DAT are flash utility programs. The VXXYYZZ.RN file has the BIOS checksum information.

  • Page 42: Bios-Contained Model Number And Serial Number

    BIOS-contained Model Number and Serial Number The model number and serial number information is stored in BIOS ROM and displayed in the “Model Information” of BIOS Setup main menu. If a service repair is completed by replacing a new system board or a new BIOS ROM, then you are required to input the original system's model number and serial number into the new BIOS ROM.

  • Page 43: Bios Setup Utility

    1. Turn on your monitor. 2. Turn on the system unit. 3. When you see the IBM Aptiva logo, press F1 to enter Setup and display the Main Menu. If you have previously set a power-on password, you are prompted to type in the password after you press the F1 key.
  • Page 44 The following table lists specific keys on the keyboard that will help you move through the Setup menus: Keys Function Down- or up-arrow key Use these arrow keys to highlight an option on the menu. (Press the Enter key to choose the option.) Left- or right-arrow key Use these arrow keys to make a selection and change an option's setting.

  • Page 45: Viewing System Information, Video Information And Model Information

    If you have made changes in Setup but would like to restore the default settings, follow these steps: 1. Press F5 to load default settings. A dialog box appears confirming if you want to load the default settings. 2. Use the left-arrow key to select Yes, then press Enter. 3.

  • Page 46: Disk Drives

    To view the video information such as the video controller and video memory, select the video information option from the setup menu. Select primary display adapter to initialize onboard VGA as the boot display device. Select Auto to initialize PCI add-on VGA card as the boot display device if a PCI add-on card is found;...
  • Page 47 • IDE Primary Channel Master is attached to IDE connector 1 on the system board and is set as the master device. This is the hard disk that comes preinstalled with your computer. • IDE Primary Channel Slave (if installed) is attached to IDE connector 1 on the system board and is set as the slave device.

  • Page 48: Input/Output Ports

    To prevent data loss, set this parameter to Auto if you are using a hard disk with more than 528 MB capacity that was previously configured through the LBA mode. If you use a hard disk configured through the user-specific cylinder- head-sector (CHS) mode, set this parameter to Disabled.

  • Page 49: Power Management

    Onboard Audio Chip This parameter enables or disables the onboard audio controller chipset. This item does not appear in the menu if there is no physical audio chipset on the system board. The default setting is Enabled. Power Management The system power management features allow you to reduce power consumption.

  • Page 50: Startup Options

    Silent Boot This parameter enables or disables the silent boot function. When set to Enabled, which is the default, BIOS is in graphical mode and displays the IBM logo while booting. If an error occurs while booting, the system automatically switches to text mode.

  • Page 51: Advanced Options

    When setting date and time, press the up- or down- arrow key to highlight a field. Press the left or right-arrow key to change the settings. Advanced Options From the Setup main menu, select the Advanced Options option to view or change a variety of configuration settings.
  • Page 52 The next time you turn on the system, you will be prompted to enter your power-on password. If you press F1 during POST to enter Setup, you must key in the password as well. If you were not able to set a password after performing the above procedure, or should you encounter any error message when setting a password, refer to “Power-On Password”...
  • Page 53 Write Protect Boot Sector Disables the write function only on the boot sector of the diskette or hard disk drive. Normal Allows the diskette or hard disk drive to function normally. This is the default setting. Onboard Floppy Disk Controller This parameter allows you to enable or disable to onboard floppy disk controller chipset.
  • Page 54 PnP/PCI Options The parameters in the PnP/PCI Options menu allow you to set the IRQ assignments for your PCI devices. PCI IRQ Setting This parameter allows for automatic or manual configuration of PCI devices. If you use Plug and Play devices, you can keep the default setting Auto.

  • Page 55: Specifications

    Specifications Dimension (width x depth x height) • System unit: 195 mm (7.68 in.) x 455 mm (17.9 in.) x 428 mm (16.85 in.) • 15" Monitor: 370 mm x 396 mm x 382 mm • 17" Monitor: 413 mm x 445 mm x 434 mm Weight •...

  • Page 56: Electrical Input

    Electrical input • Input voltage for system unit (Sine-wave input is required) - Low Range: 90 Vac to 132 Vac - High Range: 180 Vac to 264 Vac • Input voltage for 15" monitor (Sine-wave input is required) - 88 Vac to 264 Vac •...

  • Page 57: Check Procedures

    Troubleshooting .....................47 Factory-Installed Storage Devices ............47 Factory-Installed Modem Card ...............50 Audio (Not Supported by Diagnostics Program) ..........52 CD/DVD-ROM Drive ..................54 Memory ......................55 Keyboard ......................56 Mouse ......................57 Power Supply ....................59 Monitor ......................61 Undetermined Problems ................63 Copyright IBM Corp. 1998...

  • Page 58: Introduction

    Introduction This chapter contains the check procedures used to diagnose the causes of product failures. The diagnostic information consists of: Start: This is the starting point for any diagnostic action. Based on high-level symptoms, the check procedure directs you to more detailed procedures to help resolve machine failures.

  • Page 59: Start

    Computers. Do not use this diskette on other models. POST error codes and error messages are displayed on the screen after the IBM logo. Meanwhile, error beeps could be issued to help diagnose system problem. Please refer to “Index of Symptoms, Messages, Error Codes, or Beeps”...
  • Page 60 • Disconnect all drives except: - 3.5-in. diskette drive - Hard disk drive - IBM Aptiva factory-installed devices (such as a CD-ROM drive) • Ensure that all power cords and cables are connected properly. • Ensure that the monitor brightness and contrast controls are not turned...
  • Page 61 Note any symptoms, messages, error codes, or beeps. • Make sure that there are no diskette or CD in the drives. 002 - DOES AN IBM LOGO SCREEN APPEAR? (YES, READ AHEAD. NO, GO TO STEP 004.) • Insert diagnostics diskette in the diskette drive.
  • Page 62 NO, GO TO STEP 007.) • Select Diagnostics from the diagnostics program menu. • Select and execute All Tests. - Go to step 008. 007 - • The system configuration report shows only those devices supported by the diagnostics diskette. •...

  • Page 63: Index Of Symptoms, Messages, Error Codes, Or Beeps

    Index of Symptoms, Messages, Error Codes, or Beeps How to Use Error Messages: Use the messages, error codes, and beeps combinations that occur to diagnose failures. If more than one failure occurs, begin the diagnosis from the first failure that appeared. The cause of the first failure can result in false messages, error codes, or beeps.
  • Page 64 beeps, use “Table 2-2 BIOS Error Beeps List” on page 36 to diagnose system problems. 4. If you did not receive any error message, look for a description of your error symptoms in “Table 2-3 Error Symptoms List” on page 39. IMPORTANT: Check all power supply voltages, switch, and jumper settings before you replace the system board.
  • Page 65 (Continued) Table 2-1 POST Error Codes and Messages List NOTE: To diagnose a problem, first find the BIOS error messages or codes in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 66 (Continued) Table 2-1 POST Error Codes and Messages List NOTE: To diagnose a problem, first find the BIOS error messages or codes in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 67 (Continued) Table 2-1 POST Error Codes and Messages List NOTE: To diagnose a problem, first find the BIOS error messages or codes in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 68 (Continued) Table 2-1 POST Error Codes and Messages List NOTE: To diagnose a problem, first find the BIOS error messages or codes in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 69 Table 2-2 BIOS Error Beeps List NOTE: To diagnose a problem, first find the BIOS error beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 70 (Continued) Table 2-2 BIOS Error Beeps List NOTE: To diagnose a problem, first find the BIOS error beeps in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 71 Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 72 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 73 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 74 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 75 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 76 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 77 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.
  • Page 78 (Continued) Table 2-3 Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.

  • Page 79: Troubleshooting

    Troubleshooting Failing Parts or Assemblies: The check procedures generally help you trace a problem to one part or assembly. The last step of the specific check procedure you are using indicates that a part or assembly is failing. You should inspect the part or assembly before you decide to replace it.
  • Page 80 • End. 003 - • Select Utility from the menu. • Select and execute Tech Support Form from the menu to generate a system configuration report. • Compare the system configuration list with the actual devices installed in system. NOTE: If necessary, remove the cover and visually compare the devices installed in the system unit to those shown in the Tech Support Form.
  • Page 81 - In the BIOS Setup, check that the correct drive size is set for the flagged drive shown in the System Information. See “Viewing System Information, Video Information and Model Information” on page 13. • Enter BIOS Setup and load default settings. If the problem remains, check the continuity on the drive and the cable and replace it if necessary.

  • Page 82: Factory-Installed Modem Card

    Factory-Installed Modem Card NOTE: The factory-installed modem is a 56.6 Kbps modem with a cable of microphone-in and speaker-out from system board. 001 - START • In Windows 98 Device Manager, ensure that the modem is not configured with a conflicting COM port and IRQ setting. •...
  • Page 83 004 - CAN THE MODEM DIAL OUT AND CONNECT TO ANY BBS SUCCESSFULLY? (YES, READ AHEAD. NO, GO TO STEP 005.) • The modem adapter functions normally. • End. 005 - • Ensure that Windows 98 is properly installed, then power off the system unit.

  • Page 84: Audio (Not Supported By Diagnostics Program)

    Audio (Not Supported by Diagnostics Program) IMPORTANT: Audio tests for the sound card cannot be carried out in the PC- Doctor DOS diagnostics program. It is, however, possible to carry out a dial tone test for the modem. While performing this check, you may need to enter and exit Microsoft Windows 98 several times.
  • Page 85 3. Select Settings , then select Control Panel. 4. Select the Sound icon. 5. In the Sound window, select chimes from the Names field. (To test other adapter card software, select an action from a menu in that software.) 005 - IS THE PREVIEW BUTTON, OR ACTION IN OTHER SOFTWARE, SELECTABLE ON THE SCREEN (SHOWN IN BLACK AND NOT GRAY)? (YES, GO TO STEP 006.

  • Page 86: Cd/Dvd-Rom Drive

    CD/DVD-ROM Drive 001 - START • Insert the diagnostics diskette into the diskette drive and ensure that there is no CD/DVD in the CD/DVD-ROM drive. • Select Interactive Tests menu, then select and execute CD/DVD-ROM Test. 002 - DO YOU SEE A MESSAGE “NO CD/DVD-ROM DRIVE OR MSCDEX DEVICE DRIVER INSTALLED.”? (YES, READ AHEAD.

  • Page 87: Memory

    Memory 001 - START • Power off the system unit. • Insert the diagnostics diskette into the diskette drive. • Ensure that all DIMMs are installed correctly. • Power on the system unit. • Take note of any messages, error codes, or symptoms. 002 - DO YOU RECEIVE POST MEMORY ERROR MESSAGE? (YES, READ AHEAD.

  • Page 88: Keyboard

    Keyboard 001 - START • Power off system unit and ensure the keyboard plug is connected properly. 002 - • Insert the diagnostics diskette into the diskette drive and power on the system unit. • Select Interactive Tests menu, then execute Keyboard test. 003 - DOES THE KEYBOARD FUNCTION CORRECTLY? (YES, READ AHEAD.

  • Page 89: Mouse

    Mouse NOTE: A sticking key button can cause the mouse to operate incorrectly. If you suspect this, go to “Keyboard” on page 56. 001 - START • Make sure that the mouse ball turns freely. • Make sure that the mouse plug connects properly. 002 - •...
  • Page 90 • Check the mouse plug. 008 - ARE THERE ANY BROKEN PINS IN THE MOUSE PLUG? (YES, GO TO STEP 010. NO, READ AHEAD.) • Try with a known good mouse. 009 - DO THE ERROR SYMPTOMS STILL REMAIN? (YES, READ AHEAD. NO, GO TO STEP 010.) •...

  • Page 91: Power Supply

    Power Supply 001 - START ATTENTION: Check the Power Override switch, situated at the back of the machine, just above the connector for the power cable. If this switch is activated (switched to on), no power will be supplied to the system. •...
  • Page 92 Pin-hole side view Cable side view 006 - ARE THE VOLTAGES CORRECT AND DOES THE FAN RUN? (YES, READ AHEAD. NO, GO TO STEP 009.) • The power supply is working normally. • If you suspect the on/off switch cable assembly, see Step 003. •...

  • Page 93: Monitor

    Monitor First, set the system to VGA mode. To do this in Windows 98, depress the F8 function key during startup. Safe mode (VGA) will be set for Windows 98. Use the operating system's video setup to change the monitor resolution. The monitors that come with the system are DDC2A/B or DDC1/2B+ (Display Data Channel) compliant.
  • Page 94 • Select Interactive Tests from the Main Menu. • Select and execute Video test from the menu. • Follow the prompts and perform the video test. • Go to“Index of Symptoms, Messages, Error Codes, or Beeps” on page 31. • You might have to adjust the monitor controls to obtain the best image.

  • Page 95: Undetermined Problems

    4. If the jumpers, switch, and voltage settings are correct, return here and continue: • Remove or disconnect the following, one at a time: - Non-IBM devices - External devices - Any adapter card (modem card or video card, if installed) - CD-ROM drive...
  • Page 96 tested. Replace the last item tested if the system operates normally after removing the last item.

  • Page 97: Diagnostic Aids

    Diagnostic Aids Introduction ....................66 Power-On Self Test ..................66 Diagnostic Diskette ..................67 Using the Diagnostic Diskette ..............67 Using Diagnostic Program from Recovery CD......... 67 Diagnostics Program Features..............69 Copyright IBM Corp. 1998...

  • Page 98: Introduction

    BIOS version and system memory tested. For Aptiva, the F9 key will only work after exiting BIOS Setup. 3. If an error is detected during POST, the IBM logo screen will automatically switch to the text-based screen and display the error message or code with a beep.

  • Page 99: Diagnostic Diskette

    The diagnostics program comes on a diskette along with this book. This version of PC-Doctor diagnostics program, developed by Watergate for IBM, is the primary method of testing the computer. You can use it to test the IBM components of the system and some external devices. The amount of time required to test components depends on the number of components installed and selected.
  • Page 100 BIOS Setup. 3. When screen displays IBM Recovery Program menu, choose “Run Diagnostics” to execute diagnostic program. 4. Follow the instructions on the screen to operate the diagnostics program.

  • Page 101: Diagnostics Program Features

    Diagnostics Program Features Diagnostics program (PC-Doctor) includes the following features: Table 3- 1 Diagnostic Program Main Menu Selections Main Menu Selections Submenu Selections Diagnostics • System Test • Memory Test • Hard Disk Test • Floppy Disk Test • All Tests Interactive Tests •...
  • Page 102 (Continued) Table 3- 1 Diagnostic Program Main Menu Selections Main Menu Selections Submenu Selections Hardware Info • System Configuration • Memory Contents • IRQ and DMA Use • Device Drivers • COM and LPT Ports • Physical Disk Drives • Logical Disk Drives •...

  • Page 103: Repair Information

    AMD-K6 Processor (for 2158)..............86 Pentium II Processor Module (for 2163) ..........88 Celeron Processor Module (for 2163) ............93 System Backup Battery................99 Indicator LED and Cable ................100 System Board..................101 Handling ESD-Sensitive Parts ..............103 Software Recovery Procedure ..............104 Copyright IBM Corp. 1998...

  • Page 104: Removals And Replacements

    Removals and Replacements BEFORE REMOVING ANY FRU, POWER-OFF THE COMPUTER, UNPLUG ALL POWER CORDS FROM ELECTRICAL OUTLETS, THEN DISCONNECT ANY INTERCONNECTING CABLES. ATTENTION: The system board, processors, adapter cards, DIMMs, and upgrade processors can be damaged by electrostatic discharge. Use an electrostatic discharge (ESD) strap to establish personal grounding.

  • Page 105: Identifying The Parts Of The System Unit

    Identifying the Parts of the System Unit This computer system has four bays that can hold 5.25-inch and 3.5-inch drives. Additional devices can be installed in the empty bays. Diskette drives in this unit use the standard diskette advanced technology (AT) interface.
  • Page 106 5. Adapter card connectors. Adapter card connectors are sockets on the system board into which adapter cards are installed. Your system board has four adapter card connectors (for the 2163 machine, there is an additional AGP video connector). One of these connectors is for an ISA card and three are for PCI cards.

  • Page 107: Cover

    Cover • Disconnect the system unit power cord. • Remove the screws at the back of the tower. • Insert a screwdriver under one of the tabs on the back of the cover and gently pry the tower cover so that it separates from the tower. •...
  • Page 108 NOTE: Replacing the Cover • To replace the tower cover, lower the cover down over the tower, pressing in on the sides so the hooks inside the cover fit over the bottom ledge of the tower. Slide the cover forward into place. Secure the tower cover by replacing the screws you removed.

  • Page 109: Bay Panels

    Bay Panels If you remove a drive from a bay and you do not intend to install a new drive immediately, reinstall the bay panel on the empty exposed drive bay. Follow these steps to remove the plastic bay panel from the front of the system unit cover.

  • Page 110: Bay 1- 5.25-In. Bay (Internal Or External Access)

    Bay 1- 5.25-In. Bay (Internal or External Access) • Disconnect any cable on the drive (note location and orientation of cables). • Remove the screws. • Pull out the drive.

  • Page 111: Bay 2 - 5.25-In. Bay (Internal Or External Access)

    Bay 2 - 5.25-In. Bay (Internal or External Access) NOTE: If the hard disk drive is 3.5-in. and its capacity is over 10GB, it is then secured to an adapter tray to bay 2. This reduces any acoustic interference. • Disconnect any cable on the hard drive (note location and orientation of cables).
  • Page 112 • To remove the hard disk drive from the adapter tray, remove the four shoulder screws on the underside of the tray. • Four cushion rings are used to minimize the acoustic interference. To remove the cushion rings, slide and lift. ATTENTION: When installing the hard disk drive, the cushion rings and shoulder screws must be used to secure the hard disk to the tray.

  • Page 113: Bay 3 - 3.5-In. Bay (Internal Or External Access)

    Bay 3 - 3.5-In. Bay (Internal or External Access) Bay 4 - 3.5-In. Bay (External Access for Diskette Drive) • Disconnect the cables (note location of cables). • Press the lever and rotate outward. • Pull carefully and slowly as soon as the warning arrow appears. •...
  • Page 114 NOTE: Reinstall The 3.5-in Drive Frame • Before reinstalling the drive frame into the main unit, make sure the upper and lower drive frames are properly reattached. • Align the front notch of the drive frame with the system chassis •...

  • Page 115: Power Supply

    Power Supply • Disconnect all cables necessary before removal (note location of cables). • Remove the four screws from the chassis. • Push the power supply forward towards the CD/DVD-ROM drive. • Once it is sufficiently forward, place your hand underneath the power supply and push upwards to detach it from the chassis.

  • Page 116: Adapter Cards

    Adapter Cards NOTE: 1. Before removing an adapter card, note the location of the adapter card and any cables. When removing an adapter card, install the replacement card in the same slot as the one you removed. 2. If necessary, remove cards from the adjacent slots of the failed card. •...

  • Page 117: Memory(Dimm)

    Memory(DIMM) CAUTION: Memory modules are sensitive to static discharge. • Press the levers on both sides of the socket down and outwards. • Lift the DIMM to remove. ATTENTION: Place your forefingers on the top of the DIMM before you press the holding clips to gently disengage the DIMM from the socket.

  • Page 118: Amd-K6 Processor (For 2158)

    AMD-K6 Processor (for 2158) NOTE: Determine the type of processor you are installing and make sure the jumpers are set correctly. Run the Setup Utility after correctly installing a processor. CAUTION: Processors are sensitive to static discharge. • Remove adapter cards if applicable. •...
  • Page 119 • Place the processor heat sink fan over the processor. • Insert one side of fan brace onto the ZIF socket • Secure by latching the other side to the ZIF socket. • Reconnect the processor fan sink cable to the connector FN1 on the system board.

  • Page 120: Pentium Ii Processor Module (For 2163)

    Pentium II Processor Module (for 2163) The Pentium II Processor Module comes in two packages, SECC1 and SECC2. SECC stands for Single Edge Cartridge CPU. Either of the two packages can be installed to the 2163 system board. Removing the Pentium II CPU Module Follow these steps to remove the Pentium II CPU module from the slot.
  • Page 121 Pentium II Processor Installation Follow these steps to install the Pentium II processor module with heat sink and fan to the socket on the system board. • Locate the retention mechanism around the processor socket. Fold out the retainers. • With the processor module electrical contacts pointing downward, align the processor to the posts of the retention mechanism, then lower it down.
  • Page 122 • Lock the latches to secure the processor module. Installing the Processor Heat Sink and Fan The Pentium II processor module with holes on one side to hold the clips of the heat sink and fan. The upper set of holes (near the latches) on the processor are wider and should match the wider ends of the clips on the heat sink.
  • Page 123 • Using your fingers, push down the metal bracket until it clicks into the CPU cartridge and then push the metal bracket levers down, to lock the metal bracket into place. SECC2 Package Installation Follow these steps when installing the heat sink and fan to the Pentium II processor module: •...
  • Page 124 To remove the SECC2 type fan sink, use a screw driver to slide the fastener nodes outward to unlock the fan sink from the processor, then carefully remove the fan sink from the processor.

  • Page 125: Celeron Processor Module (For 2163)

    Celeron Processor Module (for 2163) Removing the Celeron CPU Follow these steps to remove the Celeron CPU module from the slot. NOTE: Determine the type of processor you are installing and make sure the jumpers are set correctly. Run the Setup Utility after correctly installing a processor.
  • Page 126 • Use a screw driver to push the four fastener tabs outward to unlock the heat sink from the processor, then carefully detach the heat sink from the processor.
  • Page 127 Installing the Universal Retention Mechanism (URM) Follow these steps to install the universal retention mechanism: 1. Pull out the sides. 2. Place the universal retention mechanism over the CPU connector on the system board and press it until it clicks into place. 3.
  • Page 128 Installing a Celeron CPU NOTE: Observe the ESD precautions when installing or removing a system component. The system board supports a Celeron processor that comes in the SEPP (Single-Edge Processor Package) type packaging. The SEPP is similar to SECC and is compatible with Slot 1 connectors. NOTE: Before you proceed, make sure that there is no processor installed in the CPU connector.
  • Page 129 5. Align the four tabs of the fastener with the four holes on the Celeron processor. 6. Press the heatsink, processor card and fastener together to lock the heatsink. Repair Information...
  • Page 130 8. With the processor card golden fingers pointing downward, align the processor to the posts of the URM. 9. Lower the processor into to the CPU connector on the system board until the golden fingers touch the connector. 10. Press down the processor until the golden fingers completely fit into the connector and the latches on the sides lock the processor into place.

  • Page 131: System Backup Battery

    System Backup Battery CAUTION: All BIOS configuration settings will be lost when the backup battery is removed! ATTENTION: Attention: Be careful when removing the backup battery. If the metal lever is damaged or broken, the system board must be replaced. •...

  • Page 132: Indicator Led And Cable

    Indicator LED and Cable • Push in on the indicator LED and remove from the rear. • Disconnect the LED and cable from the system board.

  • Page 133: System Board

    System Board • Remove all adapter cards. • Disconnect all cables connected to the system board. Note the location and orientation of all cables. • Remove the screws securing the system board to the chassis. • Lift the system board to remove from chassis. •...
  • Page 134 • Reinstall other components into the machine i.e. drives, power supply, cables, etc. • Upgrade the BIOS version on the new system board using the BIOS upgrade utility. • Change the Machine Type and Serial Number in the BIOS to match the original planar BIOS settings.

  • Page 135: Handling Esd-Sensitive Parts

    Handling ESD-Sensitive Parts Many electronic parts are sensitive to electrostatic discharge (ESD). To prevent damage when working with ESD-sensitive parts, observe the following instructions. Do these in addition to taking all the usual precautions, such as switching off the power and unplugging the power cord. •...

  • Page 136: Software Recovery Procedure

    “Startup Options”, set the first priority of boot sequence to CD-ROM. Save and exit from BIOS Setup. 3. After system boots from recovery CD, you will be prompted with an “IBM Product Recovery Program” menu, follow the instructions on the screen to...

  • Page 137: Parts/Test Point Locations

    DIMM Configurations ...................126 System Board Connector Pin Signals ............127 Monitor Port Signals................127 Serial Port Signals..................127 Parallel Port Signals................127 Mouse Port Signals ................128 Keyboard Port Signals ................128 Diskette Drive Cable Connector Signals ..........128 IDE Cable Connector Signals ..............129 Copyright IBM Corp. 1998...

  • Page 138: Introduction

    Introduction This chapter contains system board layouts and jumper settings. It is useful when you are asked to measure voltages. Use this information to help you locate parts such as electronic boards, connectors, pin numbers, and test points. This chapter also contains jumper settings for the hard disk drive, CD/ DVD-ROM (compact disc-read-only memory) drive, and the connector information for modem adapter card.

  • Page 139: Machine Type 2158 System Board Jumpers And Connectors

    Machine Type 2158 System Board Jumpers and Connectors The blackened pin of a jumper represents pin 1. 2158 System Board Jumper Settings Jumper/Settings Function VGA interrupt 1-2* Disabled Enabled Wake-on LAN signal trigger level Active low 2-3* Active high Diskette drive LED Enabled 2-3* Disabled...
  • Page 140 2158 System Board Jumper Settings (Continued) Jumper/Settings Function SW1(switch 1) Reserved SW1(switch 2, 3, 4) Bus frequency(MHz) Host AGP Off, On, On On, On, Off On, Off, Off Off, Off, Off* 100 66 SW2(switch 1) Reserved SW2(switch 3, 4) Bus frequency(MHz) Host Off, Off On, Off...
  • Page 141 Machine Type 2158 Processor Type Jumper Settings NOTE: You must verify the exact processor type before setting the processor type jumpers. The wrong processor type jumper setting may damage the CPU. The system only supports dual-voltage CPU Switch K6-2 333MHz (Host=95MHz) K6-2 350MHz (Host=100MHz)
  • Page 142 2158 System Board Connector Functions Connector Function Connect to... Universal Serial Bus (USB) connector USB device Power LED (pins 1-3) Power LED HDD LED (pins 4-7) Hard disk LED Reset button (pins 8-9) Reset button Power button (pins 10, 20) Power button IrDA connector (pins 14-19) Reserved...

  • Page 143: Machine Type 2163 System Board Jumpers And Connectors

    Machine Type 2163 System Board Jumpers and Connectors NOTE: The blackened pin of a jumper represents pin 1. 2163 System Board Jumper Settings Jumper/Settings Function Reserved Reserved Line-out signal type 1-3 & 2-4 Audio line-out 3-5 & 4-6* Amplified audio line-out Parts/Test Point Locations...
  • Page 144 2163 System Board Jumper Settings (Continued) Jumper/Settings Function SW 1 (switch 1, 2, 3, 4) Bus Clock Ratio On, Off, Off, Off On, On, On, On On, On, On, Off Off, On, On, On Off, On, On, Off On, Off, On, On On, Off, On, Off Off, Off, On, On Off, Off, On, Off...
  • Page 145 2163 System Board Connector Functions Connector Function Connect to Universal Serial Bus (USB) USB device connector ATX Power Supply Connector Power supply Upper: PS/2 mouse connector PS/2 pointing device Lower: PS/2 keyboard connector PS/2 keyboard Upper: Printer port Printer or parallel device Lower-left: COM1 Serial device Lower-right: COM2...

  • Page 146: Power Supply Connectors And Voltages

    Power Supply Connectors and Voltages Refer to the following figures when checking for voltages on power supply cable connectors. When checking voltages, the power supply fan must be running. To power-on the power supply without using the on/off switch, use a screwdriver or other tool to short the connector CN2(pin10-20) for 2158 or CN9 for 2163 (with the switch cable disconnected from the connector on the system board), or use a connection (jumper) to short the black and green wires of the 20-pin connector...
  • Page 147 (Continued) Power Supply Output Pin Assignment Voltage Cable Color Ground Black Ground Black +5Vdc +5Vdc Parts/Test Point Locations...

  • Page 148: Factory-Installed Modem Card Layout

    Factory-Installed Modem Card Layout Factory-Installed Modem Card Connector Functions Item Function Connect to... Telephone line-out Telephone set Some modem adapters may come without this jack. Telephone line-in Telephone line Voice-in/speaker-out connector System board Machine Type 2158: CN13 Machine Type 2163: CN12 NOTE: Care should be taken while connecting the voice-in/speaker-out connector.

  • Page 149: 3.5-In. Hard Disk Drive Jumper Settings

    3.5-In. Hard Disk Drive Jumper Settings 3.5-In Quantum Fireball TM Series 3.5-In Quantum Fireball ST Series Hard Disk Hard Disk 3.5-In Quantum Fireball TM and ST Series Hard Disk Drives Jumper Settings Description Drive configured as a Master, or Drive configured as a Master, with an attached Slave Drive configured as a Slave.
  • Page 150 3.5-In Seagate Hard Disk 3.5-In Seagate Hard Disk Drives Jumper Settings CS/SP Description Drive configured as a Master. Drive configured as a Slave. Drive configured as a Master, with an attached Slave The configuration of the following jumpers controls the drive's mode of operation: •...
  • Page 151 3.5-In Maxtor Hard Disk 3.5-In Maxtor Hard Disk Drive Jumper Settings Description Drive configured as a Master or Drive configured as a Master, with an attached Slave Drive configured as a Slave. Parts/Test Point Locations...

  • Page 152: 5.25-In. Hard Disk Drive Jumper Settings

    5.25-In. Hard Disk Drive Jumper Settings 5.25-In. Hard Disk Drive Jumper Settings CS/SP Description Drive is configured as a Master. Drive is configured as a Slave. Drive is configured as a Master, with an attached Slave that supports DASP The configuration of the following four jumpers controls the drive's mode of operation: •...

  • Page 153: Cd-Rom Drive

    CD-ROM Drive Front Panel and Emergency-Exit ATTENTION: Either <option 1> or <option 2> CD-ROM drive may come with your Aptiva machine. Their front panel buttons, indicators and emergency eject method may be different. CD-ROM Front Panel Introduction <option 1> Item Description Load / eject button Headphone jack...
  • Page 154 operation. CD-ROM Front Panel Introduction <option 2> Item Description Headphone jack Headphone volume control Busy indicator, lights up and flashes in amber color during data read or seek operation. Audio Play / Skip track control button Load / eject button Disc tray and emergency eject See CD-ROM Emergency-exit <option 2>...

  • Page 155: Cd-Rom Drive Rear Panel Connectors And Jumpers

    CD-ROM Drive Rear Panel Connectors and Jumpers CABLE SELECT DIGITAL SLAVE IDE INTERFACE DC INPUT AUDIO MASTER AUDIO C S M R G G L S L A NOTE: CD-ROM drives may come with no item 5 and 6 (digital audio output and testing jumper) connectors.

  • Page 156: Dvd-Rom Drive

    DVD-ROM Drive Front Panel and Emergency-Exit DVD-ROM Front Panel Introduction Item Description Disc Tray Open/Close Button Loading/Unloading/Busy Indicator Loading/Unloading Headphone Volume Control Headphone Jack Disc Indicator NOTE: Make sure to turn off the power before manual disc eject operation. DVD-ROM Emergency-exit If for any reason the tray does not eject automatically, insert and press an eject-bar inside the emergency eject hole to manually eject the tray.

  • Page 157: Dvd-Rom Drive Rear Panel Connectors And Jumpers

    DVD-ROM Drive Rear Panel Connectors and Jumpers Analog DVD-ROM Drive Rear Panel Connectors and Jumpers Item Function Connect to... Power connector Power supply IDE Interface connector System board 2158: CN10 2163: CN10 Configuration jumper. Description Master(default). Slave. Cable select Analog Audio connector System board 2158: CN15 2163: CN8...

  • Page 158: Dimm Configurations

    DIMM Configurations The 2158 system board has two DIMM sockets. A maximum of 256KB memory may be installed. The 2163 system board has three DIMM sockets. A maximum of 384KB memory may be installed. You can install 16MB, 32MB, 64MB, or 128MB PC-100 DIMM in any sockets and with any combinations.

  • Page 159: System Board Connector Pin Signals

    System Board Connector Pin Signals Monitor Port Signals Signal Name Signal Name Red Video +5 V dc Green Video Synch Ground Blue Video Monitor ID Bit 0 Monitor ID Bit 2 Synch Ground Horizontal Synch Red Ground Vertical Synch Green Ground Blue Ground Serial Port Signals Signal Name...

  • Page 160: Mouse Port Signals

    Signal Name Signal Name Busy Ground Power Paper Empty Ground Power Select Mouse Port Signals Signal Name Signal Name Mouse Data +5 V dc Power Mouse Clock Connection Ground Power No Connection Keyboard Port Signals Signal Name Signal Name Data +5 V dc Power Mouse Data...

  • Page 161: Ide Cable Connector Signals

    Signal Name Signal Name Ground Select Head 1 Motor Enable 1 Ground Ground Diskette Change IDE Cable Connector Signals Signal Name Signal Name Host Reset No Connection Ground Ground Host Data 7 Host IOW Host Data 8 Ground Power Host Data 6 Host IOR Host Data 9 Ground...

  • Page 163: Safety Inspection Guide

    Safety Inspection Guide General Guidelines ..................132 Copyright IBM Corp. 1998...

  • Page 164: General Guidelines

    If any unsafe conditions are present, you must find out how serious the hazard is and if you can continue before you correct the hazard. All current IBM Aptiva service supplements outlining feature/model changes, along with the machine history, should be reviewed.

  • Page 165: Parts Catalog

    Assembly 4: Machine Type 2158/2163 Monitor and Power Cord ....141 Assembly 5: Machine Type 2158/2163 Keyboard and Mouse .....142 Assembly 6: Machine Type 2158/2163 Zip Drive and Network Adapter ..143 Assembly 7: Machine Type 2158/2163 Software ......... 144 Copyright IBM Corp. 1998...

  • Page 166: Abbreviations

    Abbreviations In this chapter, the following abbreviations are used to identify country and language version: Country Language Version Austria Australia Belgium - Dutch Belgium - French Canada Canada - English Canada - French China Denmark - Danish Finland - Finish France Germany Hong Kong...

  • Page 167: Assembly 1: Machine Type 2158/2163 System Unit

    Assembly 1: Machine Type 2158/2163 System Unit Asm- Model Model Description Index Number 2158 2163 20L2196 Front Panel 20L2197 Hard Drive Holder 36L9138 HDD Tray 20L2193 Top Cover 20L2194 Door Cover 1-NS 02K2329 Screws for Front Panel 20L2195 Drive Bay Panel Parts Catalog...
  • Page 168 Asm- Model Model Description Index Number 2158 2163 20L2198 Assembly Lower Case (without SPS) 1-NS 02K2334 Screw for Power Supply, Bracket plate and Top Cover 1-NS 20L2206 Port Bracket Screw 1-NS 20L2207 Port Bracket Screw 20L2190 Power Switch Wire (switch + wire) + Hard Drive LED Wire (LED + wire) + Power LED Wire (LED + wire) 36L9066...
  • Page 169 Asm- Model Model Description Index Number 2158 2163 1-14 36L9100 128MB module (PC-100) 1-15 00K8468 Power Supply 95W API/Delta-854 1-071 V.B.H61 1-16 01K4278 CMOS Backup Battery (CR2032) Parts Catalog...

  • Page 170: Assembly 2: Machine Type 2158/2163 Diskette, Hard Drive

    Assembly 2: Machine Type 2158/2163 Diskette, Hard Drive Asm- Model Model Description Index Number 2158 2163 02K2299 3.5-in., 3 mode MKE (JU256A276P) 02K2603 FDD Cable 36L9105 3.5-in., 6GB Maxtor/Quasar 36L9106 3.5-in., 8GB Maxtor/Quasar 36L9107 3.5-in., 10GB Maxtor/Quasar 36L9108 3.5-in., 12GB Maxtor/Quasar 36L9101 5.25-in., 6GB Quantum/Tsunami 36L9102...

  • Page 171: Assembly 3: Machine Type 2158/2163 Cd/Dvd-Rom Drive

    Assembly 3: Machine Type 2158/2163 CD/DVD-ROM Drive Asm- Model Model Description Index Number 2158 2163 36L9087 CD-ROM 32X, Sony/LG 01K4224 IDE Cable (w/I 3Conn) 20L2289 Audio Cable, CD-ROM 00N4265 56K GVC Non-Voice Rockwell PCI NA/SA/Asia 00N4266 56K GVC Non-Voice Rockwell PCI EMEA/Australia/New Zealand 00N4267 56K GVC Non-Voice Rockwell PCI...
  • Page 172 Asm- Model Model Description Index Number 2158 2163 00N4270 56K GVC Voice Rockwell PCI (Asia) Taiwan/China/HK/ Singapore 00N4271 56K GVC Voice Roockwell PCI Japan 37L1968 56K CIS Voice Rockwell PCI NA/Taiwan/China 37L1969 56K CIS Voice Rockwell PCI EMEA/LA 37L1973 56K CIS Voice Rockwell PCI Japan 37L1974 56K CIS Non-Voice Rockwell PCI...

  • Page 173: Assembly 4: Machine Type 2158/2163 Monitor And Power Cord

    Assembly 4: Machine Type 2158/2163 Monitor and Power Cord Asm- Model Model Description Index Number 2158 2163 4-NS 06J7900 CSA/UL 10A/125V Cordset US/CE/CF/ LA/AP 4-NS 01K4196 CE-10A/250V Volex Euro 4-NS 01K4198 UK-10A/250V Volex UK/HK 4-NS 02K2648 T-Mark 10A/125V w/i adapter Japan 4-NS 13F9997 Volex 10A/250A DK...

  • Page 174: Assembly 5: Machine Type 2158/2163 Keyboard And Mouse

    Rapid Access - Belgium French, 105 keys 12J5596 Rapid Access - Japan,109 keys 12J5597 Rapid Access - Traditional Chinese 12J5566 Rapid Access - Brazilian/Portuguese 02K0814 PC Next A - Brazilian/Portuguese 76H5080 2 button Sleek Logitech M-S34 5-NS 12J4546 IBM ScrollPoint...

  • Page 175: Assembly 6: Machine Type 2158/2163 Zip Drive And Network Adapter

    Assembly 6: Machine Type 2158/2163 Zip Drive and Network Adapter Asm- Model Model Description Index Number 2158 2163 28L1605 Iomega Zip Drive, Z100ATAPI 08L2550 IBM Ethernet Adapter Lake Clark 1.6 34L0409 3COM 10/100 6-NS 36L9069 Graphics Card Parts Catalog...

  • Page 176: Assembly 7: Machine Type 2158/2163 Software

    Description Index Number 2158 2163 Aptiva owners and servicers will need to call their local IBM HelpCenter to order the above software Application CD Pack, Voice Type 3.0 Kit, Lotus SmartSuite 97, MS Windows 98 Pack and Aptiva Customized I.E. 4.0...
  • Page 177 1-NS 20L2169 3-NS 02K2334 1-NS 20L2170 3-NS 02K2603 20L2171 3-NS 02K2648 4-NS 20L2172 3-NS 06J7900 4-NS 20L2173 3-NS 06J7900 4-NS 20L2174 3-NS 08L2550 20L2187 1-12 10L6656 3-NS 20L2190 12J4546 5-NS 20L2193 12J5558 20L2194 12J5562 20L2195 12J5564 Copyright IBM Corp. 1998...
  • Page 178 Asm- Asm- Page Page Number Index Number Index 20L2196 36L9118 20L2197 36L9119 20L2198 36L9122 1-10 20L2201 1-14 36L9123 1-10 20L2202 1-14 36L9124 1-10 20L2206 1-NS 36L9125 1-10 20L2207 1-NS 36L9126 3-NS 20L2289 36L9138 28L1605 37L1968 28L3842 1-11 37L1969 34L0409 37L1973 36L9017 37L1974 36L9056...

  • Page 179: Appendix B. Online Support Information

    Aptiva technical support is offered through the IBM Online HelpCenters on the America Online. IBM online support areas on all of the services can assist with your technical questions. These areas offer message boards monitored by IBM technicians, databases of computer-related solutions, and file libraries.
  • Page 180 Here are useful IBM Internet addresses for Aptiva information: http://www.pc.ibm.com PC Company Home Page http://www.pc.ibm.com/us/aptiva Aptiva Home Page http://www.pc.ibm.com/support Aptiva Product Specifications and Support http://www.pc.ibm.com/us/searchfiles.html IBM PC Company Searchable File Library...

  • Page 181: Appendix C. Model/Monitor Configurations And Fru Part Numbers

    Appendix C. Model/Monitor Configurations and FRU Part Numbers For FRU replacement part numbers, please see Parts Catalog on page 127. Copyright IBM Corp. 1998...

  • Page 183: Index

    Error Codes and Messages List, 32 Block Mode, 15 Error Codes, 26 Error Messages, 31 Error Symptoms List 39 Cache, enable or disable, 21 Error Symptoms, 31 CD/DVD-ROM Drive ESD 103 BIOS Setup Utility, 14 External Ports, 3 Check Procedure, 54 Copyright IBM Corp. 1998...
  • Page 184 Factory-Installed Modem Card Layout 116 Hard Disk 32-bit Access, 16 Modem, 5 Hard Disk Drive Monitor 3.5-In. Jumper Settings, 117 Check Procedure, 61 5.25-In. Jumper Settings, 120 Port Signals, 127 Cable Connector Signals, 129 Monitor, 5 Hard Disk Drive, 4 Mouse Hard Disk Drive, enable or disable, Check Procedure, 57...
  • Page 185 Parallel Port, 127 System Board, 101 Serial Port, 127 Removing the Celeron CPU 93 POST, 31 Power consumption, 23 Power Management Safety Information II IDE hard disk standby timer, 17 SECC1 Package Installation 90 Power Switch 17 SECC2 Package Installation 91 Stop CPU clock in sleep state 17 Serial Port System sleep timer, 17...
  • Page 186 Printed in U.S.A. International Business Machines Corporation Old Orchard Road, Armonk, New York 10504 Part Number: 37L2040 Pub Number: S37L-2040-00 11/98...

This manual is also suitable for:

Aptiva 2158Aptiva 2163Aptiva 2235Aptiva 2236Aptiva 2237

Table of Contents