Download Print this page

Epson LQ-1500 - Impact Printer Product Support Bulletin

24 pin printer error and beep codes
Hide thumbs Also See for LQ-1500 - Impact Printer:

Advertisement

EPSON AMERICA, INC.
Product Support Bulletin
Subject: 24 Pin Printer Error and Beep Codes
Date: 4/3/91
Page(s): 1 of 4
Epson printers issue beep tones when certain error conditions exist. Those beeps
can assist you in locating and repairing customer's printers. The following error
codes are listed by product name.
NOTE: Most of the beeps issued by the printers are of .1 second duration with a .1
second pause between beeps. Where the beeps or the pauses are longer,
it has been noted in the text. The description "3 Beeps x 2" means two sets
of three beeps.
LQ-200/AP-3000
1 beep:
1 beep:
3 beeps:
5 beeps:
On-Line light is flashing:
LQ-500, LQ-510, LQ-1010, LQ-850, LQ-950, LQ-1050,
L1000, AP-4000, AP-4500
1 beep:
1 beep:
3 beeps:
5 beeps:
PSB No: P-0076
Originator JV
BEL code
A Control Panel setting is accepted.
Paper End detected
Abnormal carriage movement
Printhead is over heated. Carriage will stop until
the printhead cools down.
BEL code (.5 set beep)
A Control Panel setting is accepted
Paper End detected
Abnormal carriage movement
EPSON

Advertisement

loading

Summary of Contents for Epson LQ-1500 - Impact Printer

  • Page 1 Date: 4/3/91 Originator JV Page(s): 1 of 4 Epson printers issue beep tones when certain error conditions exist. Those beeps can assist you in locating and repairing customer’s printers. The following error codes are listed by product name. NOTE: Most of the beeps issued by the printers are of .1 second duration with a .1 second pause between beeps.
  • Page 2 PSB No: P-0076 Page: 2 of 4 LQ-800, LQ-1000, L750 1 beep: BEL code 1 beep: A Control Panel setting is accepted 3 beeps: Paper End detected 5 beeps: Abnormal carriage movement (.5 sec. pause between beeps) 5 beeps: +35V supply is abnormal LQ-860 1 beep: BEL code (.5 sec.
  • Page 3 PSB No: P-0076 Page: 3 of LQ-2500 NOTE: Printers with LCD displays use error messages along with beeps to inform the user of problems. The following messages will help you to troubleshoot problems. A blank LCD screen with the Power-on LED lit can be caused by a bent pin on one of the PROM or jumper J1 may be set incorrectly.
  • Page 4 PSB No: P-0076 Page: LQ-2550 cont. A ‘Verify After Write” check to the SRAM has failed. The SRAM could be bad. This is a motor control error. Four possible areas of failure are: a. CR home condition not detected at power up b.
  • Page 5 PC Emulator kit is also board or the UXMCL board. installed, it must go on the interface board and the 2.0 ROM Upgrade must be installed in the UXMCL board. EPSON AMERICA SERVICE, 23610 TEL0 AVENUE, TORRANCE, CALIF. 90505...
  • Page 6 7351R 2.0 ROM Upgrade Kit 7493 IBM Emulation Kit 8753 Ribbon Availability of options is subject to change without notice, contact your nearest Sales Representative or Epson Accessory Marketing for purchase. EPSON AMERICA SERVICE, 23610 TEL0 AVENUE, TORRANCE, CALIF. 90505...
  • Page 7: Service Product

    Number: P-0013A PURPOSE: This list will assist in the correct matching of Epson ribbons to printers. The numbers listed below are the Epson part numbers and can be used to order ribbons. This list supercedes PSB-013. EAI # OEM #...