8 • Operating and Cleaning Your use a solid-state speed control with this fan. Use only Hunter speed Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . 16 controls.
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 42433-01 • 01/19/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Ceiling Plate Flat Washer 3” Wood Steps 2-3 – 2-6 Screw 42433-01 • 01/19/11 • Hunter Fan Company...
Adapter 3-7. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Low Profile Washer 3-8. Place the slots over the hooks to hang the fan. 42433-01 • 01/19/11 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42433-01 • 01/19/11 • Hunter Fan Company...
Note: Should you need to remove the trim ring, press firmly on Canopy opposite sides of the trim ring directly above the groove in the Trim hanger ball. The tabs will flex out releasing the canopy trim ring. Ring Canopy Screw 42433-01 • 01/19/11 • Hunter Fan Company...
6 • Assembling the Blades 6 • Assembling the Blades Step 6-1 (Detail) Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with OR without the included light fixture.
Page 13
Steps 7-6 – 7-7 hazard or improper operation. If lights do not appear to be operating properly, see the troubleshooting section. Plug Connector Detail Housing Assembly Screw 42433-01 • 01/19/11 • Hunter Fan Company...
Page 14
(You can find the Light Bulb Sockets breakaway connector on the (B10 end of the extra chain.) Candelabra- Based 60 Watt Maximum) Metal Disc Metal Rod Glass Bowl Cover Plate Breakaway Finial Connector 42433-01 • 01/19/11 • Hunter Fan Company...
Page 15
7-19. Install the switch housing cap and plug button to the lower switch housing. 7-20. Once you have uninstalled the light fixture, continue with step 7-6. Step 7-16 Male Dummy Terminal Female Dummy Terminal Plug Button Step 7-19 42433-01 • 01/19/11 • Hunter Fan Company...
8-6. The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust In cold weather, use upward and dirt.
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 42433-01 • 01/19/11 • Hunter Fan Company...