Eizo FlexScan F930 User Manual
  1. Manuals
  2. Brands
  3. Eizo Manuals
  4. Monitor
  5. FLEXSCAN F930 -
  6. User manual

Eizo FlexScan F930 User Manual

Color display monitor
Hide thumbs Also See for FlexScan F930:
Table of Contents

Advertisement

Quick Links

English
User's Manual
FlexScan
®
F930
Color Display Monitor

Advertisement

Table of Contents
loading

Related Manuals for Eizo FlexScan F930

Summary of Contents for Eizo FlexScan F930

  • Page 1 English User’s Manual FlexScan ® F930 Color Display Monitor...

  • Page 2: Table Of Contents

    5 CLEANING ... 30 6 SPECIFICATIONS ... 31 Copyright© 1999 by EIZO NANAO CORPORATION. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao Corporation.

  • Page 3: Precautions

    PRECAUTIONS IMPORTANT! * This product has been adjusted specifically for use in the region to which it was originally shipped. The performance of the product, (i.e. picture geometry, picture positioning and color convergence and purity in the case of color monitors) is optimally adjusted to the earth's magnetic field of the specific destination.
  • Page 4 WARNING • If the monitor begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning monitor can be dangerous. • Do not dismantle the cabinet or modify the monitor. Dismantling the cabinet or modifying the monitor may result in electric shock or burn.
  • Page 5 • Do not overload your power circuit, as this may result in fire or electric shock. • For proper connections of the power cord, be certain to plug the power cord to the provided monitor connector and directly to a wall outlet. By not doing so may result in fire or electric shock.
  • Page 6 • Do not remove the tilt-swivel stand. The stand is required to maintain clearance for the ventilation slots on the bottom of the cabinet. Removing the stand will block these slots and may result in fire or electric shock. • Do not touch the plug with wet hands. Touching the plug with wet hands is dangerous and can cause electrical shock.

  • Page 7: Introduction

    INTRODUCTION About This Manual This manual explains the precautions, specifications, and operation of your EIZO monitor. Please read through this manual as it will help you to get the most out of your monitor. Package Contents: Power Cord Signal Cable...

  • Page 8: Installation

    Standard PC graphics board Using the monitor with Windows A monitor information file is saved in the EIZO CRT Utility disk included in the package. It includes all the required information for best operation with Windows 95/ Please install the enclosed utility and select your model name from the monitor list in Windows 95/98.

  • Page 9: Using The Auto-Sizing Button

    WARNING • The equipment must be connected to a grounded main outlet. • Use the enclosed power cord. If using the power cord other than the enclosed one, use the following cord. In USA and Canada, use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications: * Rating: min.

  • Page 10: Setting The Resolution

    1-3. Setting the resolution The following look-up table shows the maximum (Non-interlaced) vertical refresh rates for this model with regard to standard resolutions set forth by VESA. The best way to see if the monitor will work with a given resolution and rate, is to compare the vertical refresh rate of the graphics board to the monitor’s range (Refer to the graphics board manual for specifications).

  • Page 11: Screen Adjustment

    2 SCREEN ADJUSTMENT 2-1. How to use the ScreenManager Entering the ScreenManager Press the ENTER key to display the ScreenManager Main menu. Enter Key Arrow Key Making the Adjustments and Settings 1) Select the desired icon using the Arrow keys, and then press the ENTER key to display the each adjustment/setting menu.
  • Page 12 Size Position Side-Pin Balance/ Side-Pincushion Parallelogram/ Trapezoidal Tilt Uniformity Convergence SCREEN ADJUSTMENT Function Adjusts: Horizontal Image Size Vertical Image Size Adjusts: Screen Position Adjusts: Side-pin Balance/Side-pincushion · Tilts: Image Sides to Sides · Expands: Top Side/Bottom Side, Shirnking the Other Side Tilts: The Image Adjusts:...
  • Page 13 Adjusts: Moiré Adjusts: What is moiré? Moiré refers to an interference pattern of dark wavy lines on the screen. It is not a defect, but rather an interference phenomenon caused by the relationship between the phosphor layout and the imaging signal. Moiré...

  • Page 14: Color Adjustment

    Computer monitors generally give best performance at high temperature settings. 5,000K: Often used in printing industry. 6,500K: Good for video-image display. 9,300K: Default setting for your EIZO monitor. • The color adjustment mode SCREEN ADJUSTMENT Procedure 1) Select “Temperature”...
  • Page 15 2. To allow specific adjustments to Red, Green and Blue (R/G/B) Consists of the Cutoff and Gain functions. Cutoff and Gain adjustments Monitors use red, green and blue (R, G, and B) to convey color information. They use an additive method to combine different amounts of the primary colors to produce a desired color.
  • Page 16 Cutoff The Cutoff adjustment is the most powerful adjustment. It alters the starting point (the black level) and the ending point (the white level). If the Cutoff level for color is raised or lowered, black, white, and all levels between are raised or lowered by the same degree.
  • Page 17 3. To eliminate dispartities in color temperature and brightness due to the irregular video signal output Because of the differences in video signal output levels of graphics boards, disparities can be seen in the color temperature and brightness of the image shown on the monitor, even when the settings are the same.
  • Page 18 4. To brighten the image of photos or pictures • To switch the Text/Picture Mode The text or picture mode can be switched by the AutoSizing button. SCREEN ADJUSTMENT Procedure 1) Select the “Picture Mode” from the “Fine Contrast”. *Select the “Text Mode” to display the text on word- processor or calculating software.
  • Page 19 Complete energy use can only be stopped by disconnecting the monitor from the power supply. · When the monitor is in a power saving mode, the optional EIZO i·Sound speaker unit will turn off. · Off Timer will work while PowerManager is active, but there will be no advance notice before the monitor's power switches off.
  • Page 20 Power saving method of VESA DPMS and the monitor VESA DPMS utilizes four signals: ON, STAND-BY, SUSPEND, and OFF. The monitor detects these signals from the graphics board and executes power-saving accordingly, as shown in the table below. Signal STAND-BY SUSPEND 2.
  • Page 21 3. To decrease a slight shadowed image or charactor on its right side This monitor provides signal filter adjustments according to the characteristics of each graphics board for displaying the image properly. If the characteristics of the graphics board does not match those of the monitor, the characters and images displayed may have a slight shadow on their right side (refer to figure below).
  • Page 22 6. To set beeper on/off To set the beepr is ON, the monitor will generate beep signals as shown below. To set the beeper is OFF, the monitor will not beep. Short beep Long beep Four short beeps Two short beeps every fifteen seconds 7.

  • Page 23: Shortcut Keys

    2-3. Shortcut Keys Before entering the ScreenManager, brightness and contrast can be adjusted directly by moving the Control pad. To record the new setting and exit the ScreenManager, press the Enter key. (The brightness and contrast functions are also available in the ScreenManager “contrast/brightness”...

  • Page 24: Sub And Bnc Input

    1) Be sure that the monitor and the PC are both switched off before connecting them. 2) Connect one PC to the monitor’s D-Sub connector and another to the BNC connector securely. The BNC connection should be made with an EIZO BNC cable, available as an option. Contact EIZO dealers for information about optional cables.
  • Page 25 If signals from both inputs are present, the monitor gives preference to D-Sub for the cases shown below: D-Sub • When the power of the monitor is turned ON. • When the signal input to D-Sub is changed even if active input was BNC.

  • Page 26: Troubleshooting

    4 TROUBLESHOOTING Troubleshooting If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems 1) Indicator status: OFF 2) Indicator status: GREEN 3) Indicator status: GREEN (flashing) 4) Indicator status: YELLOW 5) Indicator status: YELLOW (flashing) 6) Following message appears.
  • Page 27 It may be solved by switching off or moving the interfering device, or by relocating the monitor. If the volume level of the EIZO optional i·Sound speaker is too high, it may, in some cases, cause a slight vibration. To eliminate, turn down the volume of the speaker.
  • Page 28 PC and operating system. Flicker will occur with interlaced scanning, or non- interlaced scanning with a low refresh rate. All EIZO monitors are capable of reproducing high refresh rates for non-interlaced scanning. If a problem occurs when using a non-interlaced signal, try adjusting the graphics board to increase the refresh rate (if possible).
  • Page 29 Explanation of the Characteristics of CRTs When the monitor is not fully warmed up, the screen may look slightly colored, e.g. reddish or bluish. This phenomenon is due to the unstableness of the electron gun during its warm-up period. Please wait for about 30 minutes until the monitor stabilizes in order to gain its proper color.

  • Page 30: Cleaning

    5 CLEANING WARNING • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again.

  • Page 31: Specifications

    * The actual size displayed can be dependent on the graphics board or PC utilized. 100-120/220-240 VAC±10%, 50/60 Hz, 1.8/0.8 A 130 W/150 W* (* with EIZO optional speaker attached) D-Sub mini 15-pin and BNC × 5 (Switchable) 1600 dots × 1200 lines •...

  • Page 32: Pin Assignment

    Pin Assignment D-Sub mini 15 pin connector BNC connector Connector Input signal Sync on green Composite sync Separate sync SPECIFICATIONS Pin No. Signal Red video Green video/ Green video/ Green video Green video Composite Sync Blue video Ground No pin Red ground Green ground Blue ground...

  • Page 33: Preset Timing

    Preset Timing 2 factory presets shown below have been registered in the monitor’s microprocessor. Resolution fH (kHz) × 31.47 (text) × VESA 1600 1200 106.25 Dimensions Frequen cies Interlace Sync Polarity fV (Hz) 70.09 H/Negative 85.00 Video Signal Level 0.7V(p-p)/ V/Positive 75 Ohm H/Positive...
  • Page 34 MEMO SPECIFICATIONS...

  • Page 35: Why Do We Have Environmentally Labelled Computers

    Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.

  • Page 36: Environmental Requirements

    Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.

  • Page 37: Fcc Declaration Of Conformity

    Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device. -AC Cord -Shielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclosed signal cable) This Class B digital apparatus complies with Canadian ICES-003.
  • Page 38 Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend abgeschirmt. Recycle Auskunft Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem Partner von Roll MBB Recycling GmbH. Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden.

Table of Contents