Advertisement
Quick Links
6. Control Panel and Program Description
Press the "Speed"
It displays delay time,
Press the "Temp." button to
The variable frequency series is set with the "Auto" function. In this mode, press the "Power" button, the washer will turn on and the door will
button to select
remaining washing time,
select heating temperature
automatically open; put the clothes to be washed into the washer and close the door, the display screen will display " "; press the
spinning speed.
times of extra rinse,
"Start/Pause" button, the washer will automatically weigh the clothes and select the optimal washing program, achieving water, electricity
(--, 30, 40, 50, 60, 90). The
The maximum
spinning time, set
and time saving.
maximum allowable
If you do not want the washer to weigh the clothes automatically, press the "Auto" button to switch to manual selection of
allowable spinning
temperature, set speed,
heating temperature varies
Note:
clothes weight level (the operation is the same as that of non-variable frequency series).
speed varies with
clothes weight level, child
with programs.
(1) In manual mode, it is recommended that "L-4" or "L-A" be selected for washing many clothes (more than a half drum) and "L-1", "L-2" or
programs.
lock state, door lock state
" － " in the temperature
"L-3" be selected for washing fewer clothes (not more than a half drum).
and alarm message, etc.
display area indicates
(2) The "Auto" function is only available for the "Prewash", "Cotton", "Synthetic", and "Wash" programs. For other programs, press this button
non-heated washing.
to manually adjust the clothes weight level (the level adjustment is not available for the "Wool" program).
"Speed" selection
Display screen
"Temperature" selection
Star t /
D elay
E xtra Rinse
Strong
Auto
"Delay" button
"Extra rinse" button
Press the "Extra rinse" button to increase the times of rinse
Press the "Delay" button, its indicator will light up, indicating
(at most three times) between the "Rinse" and "Soften"
this function is selected. The delay time (0.5-24h) increases by
30 minutes each press of "Delay" button. The time will change
programs.
When the indicator of "Extra rinse" lights up, it means this
continuously if you press and hold this button until you release
function is selected. Each press of the "Extra rinse" button
it.
increases one time of rinse. P--1~P--3 shows on the
The delay time is the end time of washing. For example, 6:00
display screen. Press this button again, this function will be
means the washing ends after 6 hours (the delay time must be
longer than the program's running time).
cancelled and the indicator will go out.
This function is not available for the "Wash" and "Spin"
This function is not available for the "Spin" program.
programs.
7. Display Screen
Numerical display area
Child lock icon
Door lock icon
1. Numerical display area: the delay time, remaining time, times of extra rinse and alarm message, etc. display in this area.
When the washer is in operation, remaining time displays in this area; if you turn on the washer after the selected program
ends, the program time of last washing will display in this area, e.g. 1:28; when the "Delay" function is selected, the delay time
will display in this area, e.g. 6:00; when the "Extra rinse" function is selected, the additional times of extra rinse will display in
this area, e.g. P--1; when the program running is abnormal, alarm message will display in this area, e.g. Err3.
2. Child lock icon: simultaneously press the "Delay" and "Start/Pause" buttons and hold them for 3 seconds, the child lock
function will be activated to avoid changing the selected program by inadvertent touch of buttons; simultaneously press the two
buttons and hold them for 3 seconds again, this function will be cancelled.
3. Door lock icon: this icon will light up when the door is closed and will not show when the door is opened.
Note:
The time shown on the display screen is only for reference and may be slightly different from actual
time due to water temperature and water pressure, etc.
The child lock function will be cancelled when the selected program ends, power failure occurs or the
washer is switched off.
Select the desired
program by turning
this knob.
After turning on the
washer, it
automatically
selects the
program of last
washing.
"Auto"/"Clothes weight level selection" button
Program knob
Unde wear
r
Sport Wash
Wool
Quick
Press the "Power" button to
S-D Inverter
switch on the washer.
Wash
Synthetic
Press this button again and
hold it for 2 seconds to
Cotton
R
inse
switch it off.
After switching on the
Prewash
S
pin
washer, if any button is not
pressed within 5 minutes, it
will automatically turn off.
Pause
HW55-B12866NZP
Press and hold 2seconds
to set door unlocked
"Strong" button
"Start/Pause" button
Press the "IStrong" button to select or
Press the "Start/Pause" button, the
cancel the function of intensive washing.
washer will start or pause. When the
This function is to increase washing time,
washer pauses, the indicator will
times of rinse and spinning time of the
flash.
main wash stage of the selected program.
When the washer is turned on and
When the "Strong" indicator lights up, it
the "Start/Pause" button is not
means this function is selected. This
pressed, you may open the door by
function is not available for the "Rinse" and
pressing and holding this button for 2
"Spin" programs.
seconds.
8. Other functions
Function
Eccentric protection
When spinning, if the clothes are not evenly distributed, the washer will fluff out
and redistribute the clothes and continue spinning after the clothes distribution
becomes even. If the clothes distribution does not become even within the
Function
Power-down memory
specified time, the washer will not spin to avoid abnormal vibration. In this case,
With the power-down memory function, the washer can
please check the clothes for intertwist and rearrange them, then select "Spin"
memorize the program's running state in case of power
program to spin the clothes. When there are few clothes, the washer may not spin
failure or loose plug during washing and continue the
due to eccentric protection. In this case, you can put more clothes into the washer
formerly selected program after the power supply resumes.
and make them evenly distributed, then continue spinning. In addition, it is normal
that the program time will prolong because the washer rearranges and fluffs out
the clothes.
Function
Cancel or reselect a program during washing
(1) To cancel the running program, just turn off the washer;
to reselect a program, turn it on again.
(2) To select any additional function when a program is
Function
Silencing function
running, just press the "Start/Pause" button, then select your
Select the "Spin" program, simultaneously press the "Delay" and "Extra rinse"
desired additional function and finally press the
buttons and hold them for 3 seconds, the beep of all the programs (excluding the
"Start/Pause" again.
alarm sound) will be silenced and the display screen will show "
Simultaneously press the two buttons and hold them for 3 seconds again, the
beep of all the programs will resume and the display screen will show "
Note:
The above operations should be made when the child lock is
not activated.
The method (2) is only available for several function buttons.
9. Fault Clearance
The following phenomena are not necessarily faults of the washer. Please check against the following table before calling for repair.
If any fault actually exists, please contact our After-sales Service Department and do not repair by yourself. Please pull out the power plug before check.
State
Phenomenon
Solution
Programs Guide
There is a little water in
It is normal; the water is the remaining
the drain pipe and
water of factory inspection
washer when using the
washer for the first time
Check whether power failure or abnormal
power supply occurs
Prewash
For washing relatively dirty
Check whether the power plug is firmly
cotton fabrics
inserted into the socket
Check whether the fuse of power supply or the
The washer does
Cotton
For washing cotton fabrics
current breaker is in good condition
not operate
Check whether the "Power" switch is turned on
Check whether the water tap is turned on
Check whether the "Delay" function is selected
Synthetic
For washing chemical fiber
Check whether the "Start/Pause" button is
fabrics
pressed
Wool
For washing wool fabrics
Check whether the "Child lock" function is
Buttons cannot be
selected
operated
After starting, to select other programs,
Underwear
For washing cotton underwear
please press the "Start/Pause" button and
or children's clothes
then operate
Check whether the water tap is in proper shape
Water leakage occurs
Check whether the water inlet pipe joint is
For washing sport wear
Sport Wash
at the water tap
installed in place
Check whether the water tap is damaged
Quick
For washing slightly dirty cotton
Check whether the water tap is turned on and
whether water supply cut-off occurs
and chemical fiber fabrics
Check whether the water inlet valve is clogged (if
No water inflow or
necessary, clean the valve)
Check whether the water tap and water inlet pipe
slow water inflow
are frozen
Wash
Check whether the "Delay" program is selected
For washing the clothes only
Check whether the "Start/Pause" button is pressed
Check whether the water inlet pipe is bent
Check whether the water pressure is too low
Rinse
For rinsing the clothes only
Water feeding and water
Check whether the height of drain pipe
drainage occurs at the
orifice is within the range of 80cm~100cm
same time
Check whether the drain pipe orifice is
Spin
For spinning the clothes only
immersed in the water
Check whether the washer inclines or shakes
Check whether there are foreign bodies such
as coins and zippers in the washer
Abnormal noise
Check whether the noise is from the buttons
and zippers of washing
Check whether the noise is from the draining
pump or motor in normal operation
10.Cleaning/Maintenance
Please pull out the power plug from the socket before
cleaning and maintenance.
Filter cleaning (once a month as recommended)
Fig. 1
(1) After draining the water in the washer, open the filter door by pressing it
down with a flat head screwdriver or a similar tool through the square hole
above the filter door (as shown in Fig. 1).
(2) Hold the plastic pipe plug to pull out the waste pipe, prepare a water
Filter
container, remove the plastic plug of waste pipe to drain the remaining
water into the container (as shown in Fig. 2), replace the plastic plug onto
Fig. 2
the waste pipe, and finally clamp the waste pipe in original position.
(3) Anticlockwise screw out the filter. It is normal that a little water flows out
at this time (as shown in Fig. 3).
Waste pipe
(4) Rinse with clean water (as shown in Fig. 4).
(5) Insert the filter after aligning its convex with the groove of draining pipe,
Waste pipe plug
Water container
then clockwise tighten it (as shown in Fig. 5), and finally close the filter door.
".
".
Fig. 3
Fig. 4
Fig. 5
State
Phenomenon
Solution
Displayed code
Code meaning
The washer is in automatic
Check whether the type and dosage of
weighing state
Poor washing effect
detergent are suitable
Check whether the selected program is
correct
The remaining washing time is
one hour and sixteen minutes
Check whether the clothes weight
Forceless washing
exceeds the washer's rated washing
The spinning speed is set
at 800 rpm
capacity
Check whether sudden power failure
The whole program ends
Stop operation
or water supply cut-off occurs
during washing
Check whether the "Start/Pause"
button is pressed
Abnormal door locking or
unclosed door
The washer's program is set with
water discharge time and the
spinning starts after a period of time
No spinning
Drainage fault
Check whether the clothes intertwist
Check whether too much washing
powder was added
Temperature sensor fault
Check whether the washer is washing
Excessively long
a single piece of clothing, e.g. woolen
spinning time
sweater. If so, it is normal
Heating fault
Check whether all the fixing bolts for
transport are removed
Check whether the washer is level (the
Loud noise when spinning
washer can be leveled by adjusting the feet)
Vibration and
Check whether the clothes intertwist
displacement
Check whether the washer collides with
Abnormal water inflow
other objects
Check whether there are foreign bodies in
the washer
The clothes are not
spun dry after finishing
The spinning effect varies with the
type of clothes
the "Spin" program
The motor speed is higher
Check whether it is for eccentric
or lower than the pre-set
protection with few clothes
speed
Check whether the drain pipe is bent,
The motor stops running
No water discharge or
clogged or frozen
slow water discharge
Check whether the drain pipe orifice is
100cm higher than the floor
Check whether the filter is clogged
The water level exceeds
alarm level
The control panel is
partially hot
It is normal that electronic
components are slightly hot
Water level sensor fault
The washing does not
The clothes distribution becomes
end after the preset
imbalanced during washing
delay time
Poor water feeding/drainage
Uneven clothes distribution
conditions result in a longer time
while spinning
Cleaning of a distributor box
To clean a distributor box, pull it out, gently
press it down and continue to pull it out (as
shown in the figure on the right), remove it,
rinse it with water and reinstall it in place.
Cleaning of the filter screen of water inlet valve
Frequently clean the water inlet pipe joint and
water inlet
the filter screen of water inlet valve to prevent
valve joint
them from being clogged by impurities (as
shown in the figure on the right)
Note:
Please clean the filter screen of water
inlet valve as shown in the figures below.
Note:
The filter must be
tightened to avoid
Reinstall the filter
Take out the filter screen
Wash the filter screen
water leakage.
screen in place
Solution
Displayed code
Code meaning
Solution
Communication fault
Please ask for repair
Being inconsistent with the
conditions for door opening,
it is not allowed to unlock
the door
Note:
and
alarms are limited to the variable frequency series.
is limited to the non-variable frequency series.
Close the door; if the problem
It is normal that the washer discharges water when
or
occurs.
remains, please ask for repair
Clean the draining pump filter
and check whether the drain
pipe is clogged; if the problem
remains, please ask for repair
Please ask for repair
Warm tips
To add clothes during washing or to take out clothes
after extended power failure, make sure that the
Pull wire
water level in the drum is properly below the lower
Please ask for repair
edge of sight glass, the water temperature is below
Shut down the washer and
remove the problem.
Check
the drain pipe from its holder and put it down until no
whether the water tap is turned on,
water is drained from the drain pipe, afterwards put
whether the water pressure is too
back the drain pipe. Open the filter door at the bottom
low, whether water supply cut-off
occurs;
Check whether the
of washer, and you will see a pull wire. Take out the
water inlet valve is clogged
pull wire and gently pull it downwards until you hear a
(please clean it); if the problem
low sound, the door will open, now you can add or
remains, please ask for repair
take out the clothes. Afterwards, reset the pull wire
Shut down the washer and
and filter door.
remove the problem; if the
problem remains, please ask for
repair
Please ask for repair
Note:
Never perform the above operations when the washer is running.
The washer automatically
removes this problem; if the
problem remains, please
The washer contains recyclable materials. Please properly dispose of them to protect
ask for repair
the environment.
Adding a proper amount of softener may make the clothes soft, eliminate sticking arising
Please ask for repair
from static electricity and make the clothes easier to be ironed. Excessive soften may
damage synthetic fiber. Please refer to its instructions for correct dosage of softener.
Take out and fluff out the
clothes; if the problem
remains, please ask for repair
Advertisement
