Edelbrock 68882 Installation Instructions

Please study these instructions carefully before installing your new Tubular Exhaust System (TES). If you have any questions, please contact our
Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at Edelbrock@Edelbrock.com.
TUBULAR EXHAUST SYSTEM: These components are designed as a system to improve the exhaust efficiency of the GM T.B.I. (Throttle Body
Injection) V6 engine. A performance gain can be expected by the installation of the system. This system requires no welding for installation and
retains all O.E.M. emissions equipment.
Vehicle Applications:
Catalog #68882, #68883 - 1988-1993 Chev/GMC Pick-Up Trucks 1500/2500 Series, 4.3L V6 T.B.I., 2 WD, Auto & Standard Transmission,
Catalog #68892, #68893 - 1988-1993 Chev/GMC Pick-Up Trucks 1500/2500 Series, 4.3L V6 T.B.I., 2 WD, Auto & Standard Transmission,
Suggested Tools Needed for Installation: This vehicle has metric fasteners.
❑
3/8" ratchet socket set with extensions and universal 13mm and 15mm swivel sockets
❑
Combination set of open-end wrenches
❑
Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑
Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695)
SPECIAL NOTICE: This Edelbrock Tubular Exhaust System has received an Executive Order number (E.O.#) from the California Air Resources Board
(C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we have included a silver fan shroud
decal to help testing personnel verify the this part is a legal replacement on the vehicle for which it is cataloged. The adhesive-backed decal should
be affixed next to the existing emission and engine specifications decal. Do not cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock Tubular Exhaust Systems.
Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the system.
NOTE: High temperature spark plug wires and boots are recommended to withstand heat from T.E.S.
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor
• DISASSEMBLY
1. Disconnect battery negative cable from battery.
2. Raise vehicle and support with jackstands.
3. Use penetrating oil on all nuts and bolts to be removed. This
will prevent the possibility of broken or stripped nuts and bolts.
4. Making sure the converter is cool, remove the exhaust
crossover pipe.
5. Lower vehicle to the ground.
• DISASSEMBLY - LEFT SIDE
1. Remove air cleaner system (note position of line and hose
connections).
2. Disconnect A.I.R. (air injection reactor) tube from exhaust
manifold (#68892 / #68893 only).
3. Remove air conditioner compressor rear support bracket (if air
conditioning equipped).
Catalog #68882, #68883, #68892, #68893
©2006 Edelbrock Corporation
Without A.I.R.
With A.I.R.
IMPORTANT NOTE:
performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

Catalog #68882, #68883, #68892, #68893
4. Remove power steering pump support bracket (if power
steering is applicable). In order to remove the OEM bracket
attached with the two front exhaust manifold bolts on some
models, it may be necessary to remove the power steering
pump pulley. This requires the use of a special power steering
pulley puller, such as K-D 2897 or equivalent.
5. Disconnect spark plug wires and remove spark plugs.
6. Remove 02 sensor, being careful not to rupture or destroy the
unit.
WARNING: Do not clean this unit in any cleaning solvent and
do not rupture wire.
DISASSEMBLY - RIGHT SIDE
1. Disconnect A.I.R. injection tube from exhaust manifold
(#68892 / #68893 only).
2. Disconnect spark plug wires and remove spark plugs.
Page 1 of 2
TUBULAR EXHAUST SYSTEM
Vehicle Applications: See Below
INSTALLATION INSTRUCTIONS
Brochure #63-68882
Rev. 6/06 - DA/mc