Page 1: User Manual
SyncMaster P50FP,P63FP PDP Monitor User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3: Installation
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. •...
Page 4 Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet.
Page 5 Safety Instructions When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it softly with a dry cloth.
Page 6 Safety Instructions If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Page 7 Safety Instructions If you continually move closer to the product screen, your eye- sight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Page 8 Safety Instructions The batteries (and rechargeable batteries) are not ordinary re- fuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Page 9: Package Contents
Introduction Package Contents Note Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking PDP Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions)
Page 10 Introduction Others (Not available in all loca- (3301-001305) tions) Sold separately DVI Cable Wall Mount KIT LAN Cable TV tuner box NetWork Box Semi Stand KIT (P50FP) BNC Cable Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals.
Page 11 Introduction Your PDP Display Front SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only al- lowed for external devices that are connected to the PDP Display at the time. [PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [TV] → [BNC] → [Com- ponent] Note •...
Page 12 Introduction Power indicator Shows PowerSaver mode by blinking green. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the PDP Display.
Page 13 Introduction BNC/COMPONENT OUT [R/P , G/Y, B/ , H, V] (BNC/Component Connection Ter- minal (Output)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. Component Connection: connecting the P Y, P ports. BNC/COMPONENT IN [R/P , G/Y, B/ , H, V] (BNC/Component Connection Ter- minal (Input)) RS232C OUT/IN (RS232C Serial PORT)
Page 14: Using The Anti-Theft Kensington Lock
Introduction Connect the [ VIDEO ] terminal of your PDP Display to the video output terminal of the external device using a VIDEO cable. AV/COMPONENT AUDIO IN [L- AUDIO - R] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ L- AUDIO - R ] port of the PDP Display.
Page 15 Introduction Rear(P63FP) Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The PDP Display 's configuration at the back may vary slightly depending on the PDP Display model. POWER The power cord plugs into the PDP Display and the wall plug.
Page 16 Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AU- DIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your PDP Display to the HDMI terminal of your digital output device using a HDMI ca- ble.
Page 17: Remote Control
Introduction Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display , causing a malfunction due to interference with the frequen- POWER Number Buttons button + VOL - MUTE TV/DTV MENU...
Page 18 Introduction Turns the product On. POWER Turns the product Off. 3. Number Buttons Press to change the channel. The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. 4. DEL button 5. + VOL - Adjusts the audio volume.
Page 19 Introduction This button is used to return to the immediately previous ENTER/PRE-CH channel. CH/P In TV mode, selects TV channels. 21. D.MENU DTV menu display 22. GUIDE Electronic Program Guide (EPG) display. Returns to the previous menu. RETURN 24. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically tons or adjusts selected menu values.
Page 20: Network Model Size
Introduction 31. SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. - This fuction does not work for this PDP Display. Mechanical Layout (P50FP) Mechanical Layout NETWORK MODEL SIZE...
Page 21: Installation Vesa Bracket
• At least 2 persons are needed in order to move the PDP Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Page 22: Wall Bracket Assembly
Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic Screw Screw Anchor Hanger (A)(11) (B)(4) (11) Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall.
Page 23: To Mount The Product On The Wall Bracket
Introduction Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
Page 24 Introduction Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
Page 25: Wall Bracket Angle Adjustment
Introduction PDP Display Wall Bracket Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 26 • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 27 Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic Screw Screw Anchor Hanger (A)(11) (B)(4) (11) Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall.
Page 28 Introduction Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
Page 29 Introduction Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
Page 30 Introduction PDP Display Wall Bracket Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 31: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance.
Page 32: Connecting Av Devices
Turn on both your computer and the PDP Display. • The DVI cable or BNC cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth •...
Page 33: Connecting To A Camcorder
Connections Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the PDP Display. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Select AV using the SOURCE . Note The PDP Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders.
Page 34: Connecting A Dvd Player
Connections Connecting a DVD Player Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display and the AUDIO OUT jacks on the DVD player. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the PDP Display.
Page 35: Connecting Using A Dvi To Hdmi Cable
Connections Note • Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the PDP Display or on the remote control. • For an explanation of Component video, see your Set Top Box owner's manual. Connecting Using a HDMI Cable Note •...
Page 36: Connecting To An Audio System
Connections Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on PDP Display.
Page 37: Using The Software
Using the Software Installation MagicInfo Pro Installation Insert CD into the CD-ROM drive. Click the MagicInfo Pro installation file. When the Install Shield Wizard window appears, click "Next." Select "I agree to the terms of the license agreement" to accept the terms of use. You are required to log in to the MagicInfo Pro Server program.
Page 38 Using the Software Choose a folder to install the MagicInfo Pro program. Click "Install."...
Page 39 Using the Software The "Installation Status" window appears. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish".
Page 40: System Requirements
Using the Software 10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Ethernet Application Minimum P1.8 256M 100M/1G Windows WMP 9 or Win- later Recom- P3.0GHz 512M...
Page 41: Main Screen
Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Page 42: Port Selection
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3.
Page 43: Power Control
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the PDP Display using a serial cable is not selected, communication will be unavailable.
Page 44 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display. 1) Power On/Off...
Page 45: Input Source
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
Page 46: Image Size
Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
Page 47 Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
Page 48 Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
Page 49: Pip Size
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
Page 50: Pip Source
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
Page 51 Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the PDP Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC.
Page 52: Picture Pc
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
Page 53 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 54: Image Lock
Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 55: Maintenance
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
Page 56 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
Page 57: Video Wall
1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type.
Page 58: Troubleshooting
Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 PDP Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
Page 59: Settings Value Display In Multiple Display Mode
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 .
Page 60: Available Modes
Adjusting the PDP Display Input Available Modes • PC / BNC / DVI • • HDMI • MagicInfo • • Component Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Source List MENU →...
Page 61: Edit Name
Adjusting the PDP Display This is deactivated when a TV tuner box is installed. MagicInfo This is activated when a network box is installed. This is activated when a TV tuner box is installed. Component Note • The direct button on the remote control is the 'SOURCE' button. Edit Name MENU →...
Page 62 Adjusting the PDP Display Picture [PC / BNC / DVI / HDMI / MagicInfo Mode] Available Modes • PC / BNC / DVI / HDMI • • MagicInfo • • Component Note • The TV menu is available when a TV tuner box is installed. •...
Page 63 Adjusting the PDP Display Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Page 64: Color Control
Adjusting the PDP Display Cool Normal Warm Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled. If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance.
Page 65 Adjusting the PDP Display Note This function is only enabled if the Color Tone is set to Off. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
Page 66 Adjusting the PDP Display The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. (Available in PC mode only) Note The direct button on the remote control is the 'AUTO' button. Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable.
Page 67 Adjusting the PDP Display MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → → ENTER → [Signal Control] → → → ENTER → [B-Gain] → , → ENTER R-Offset MENU → →...
Page 68 Adjusting the PDP Display • • HDMI / DVI • MagicInfo • • Component Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Mode MENU →...
Page 69 Adjusting the PDP Display Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → → ENTER → [Custom] → → ENTER → [Bright- ness] → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → →...
Page 70 Adjusting the PDP Display Cool2 Cool1 Normal Warm1 Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled. Color Temp. MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER Color temp is a measure of the 'warmth' of the image colors.
Page 71 Adjusting the PDP Display • ZOOM1, ZOOM2 will be unavailabel in HDMI mode. • The Position and Reset functions are available when ZOOM1 or ZOOM2 is run. Digital NR (Digital Noise Reduction) MENU → → ENTER → [Picture] → → →...
Page 72 Adjusting the PDP Display • HDMI • MagicInfo • • Component Note • The TV menu is available when a TV tuner box is installed. • The MagicInfo menu is available when a network box is installed. Mode MENU → →...
Page 73 Adjusting the PDP Display • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ENTER→ [Bass] → , → ENTER Emphasizes low frequency audio. Treble MENU →...
Page 74: Available Modes
Adjusting the PDP Display SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound ex- perience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
Page 75: Clock Set
Adjusting the PDP Display You can choose one of 11 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU →...
Page 76: Off Timer
Adjusting the PDP Display On Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→ [On Timer] → → ENTER Turns the PDP Display on automatically at a preset time. Controls the mode and the volume level at the time the PDP Display turns on automatically.
Page 77: Safety Lock Pin
Adjusting the PDP Display Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0~9] → [0~9] → [0~9] → [0~9] The password can be changed. Note The preset password for the PDP Display is "0000".
Page 78 Adjusting the PDP Display When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI black level.
Page 79 Adjusting the PDP Display The Format can be selected to see a divided screen. Full Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU → → → → ENTER → [Setup] → → → → →...
Page 80: Screen Divider
Adjusting the PDP Display Screen Divider MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video → → → → ENTER → [Screen Divider] Wall ]→ The screen can be divided into several images. A number of screens can be selected with a different layout when dividing.
Page 81 Adjusting the PDP Display Note The Pixel Shift is not available when Video Wall is On. Horizontal Dot MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → →...
Page 82 Adjusting the PDP Display Timer Timer MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → ENTER → [Timer] → → ENTER You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.
Page 83 Adjusting the PDP Display Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → →...
Page 84 Adjusting the PDP Display This function prevents after-images on the screen by moving long black and white vertical lines. Eraser MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → →...
Page 85: Resolution Select
Adjusting the PDP Display This function prevents after-images on the screen by moving a diagonal pattern stored in the panel repeatedly. Resolution Select MENU → → → → ENTER → [Setup] → → → → → → → → →ENTER → [Resolution Select ] →...
Page 86: Side Gray
Adjusting the PDP Display Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage. Side Gray MENU → → → → ENTER → [Setup] → → → → → → →...
Page 87: Color Reset
Adjusting the PDP Display Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → [Setup] → → → → → → → → → → → → ENTER → [Reset ]→ → ENTER → [Color Reset ] → , →...
Page 88 Adjusting the PDP Display • • HDMI • MagicInfo • • Component Note • The operating system for this set only supports English so the other languages might be corrupted on the screen. • For MagicInfo, a remote control is available for MagicInfo. However, it is recommended using a separate USB keyboard.
Page 89 Adjusting the PDP Display • When the contents of Setup have been changed when EWF is in the Enable state, to save the changes in the disk, you must Commit them. • By selecting Disable, Enable or Commit, the system is restarted. Magicinfo 1.
Page 90 Adjusting the PDP Display 4. Connect your keyboard and mouse and press the “ALT + F12” keys on your keyboard. 5. The Windows Desktop is displayed and the Magicinfo pro icon (the image will be inserted) appears. Move the cursor over the icon. Note If the Magicinfo icon is not displayed on the notification area, double click the Magicinfo icon on the window desktop.
Page 91 Adjusting the PDP Display 7. The Player screen of Magicinfo pro is displayed. Note To finish the MagicInfo, press ALT + F12. Photo The JPEG, BMP file format are supported.
Page 92: Slide Show
Adjusting the PDP Display Auto Automatically fits the image to the window. Original Shows the properties of the original file. Slide Show Displays the properties of the original file as they are.
Page 93 Adjusting the PDP Display Interval Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec) Rotation Displays an image file by turning it clockwise by 90 degrees.
Page 94 Adjusting the PDP Display Zoom Displays a reduced picture. Close Closes the image control Menu.
Page 95 Adjusting the PDP Display Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported. Play Plays a movie file.
Page 96 Adjusting the PDP Display Full Size Plays a movie file in full screen. OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments.
Page 97: Schedule View
Adjusting the PDP Display Internet Connects to the Internet Setup Sets various functions in MagicInfo mode. A password must be entered to access Setup mode. Schedule View Displays a schedule.
Page 98 Adjusting the PDP Display TCP/IP Changes the TCP/IP settings. Connection Modifies the network settings.
Page 99 Adjusting the PDP Display Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) • If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server.
Page 100 Adjusting the PDP Display Play Option You can set the repeat play and screen settings. Repeat : Determines the repeat option for playing movies and music. • None - Select No Repeat to play a movie or tune in the list only once. •...
Page 101: Troubleshooting
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the PDP Display. Unplug the video cable from the back of the computer. Turn on the PDP Display.
Page 102: Symptoms And Recommended Actions
Do not use benzene, thinner or other flammable sub- stances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly.
Page 103: Problems Related To The Screen
Troubleshooting Check if the signal cable between the computer and the PDP Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the PDP Display screen and their solutions are listed. The screen is blank and the power indicator is off.
Page 104: Problems Related To Audio
Troubleshooting The screen color is inconsistent. Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 105: Problems Related To Magicinfo
Troubleshooting Check the polarities (+/-) of the batteries. Check if the batteries are empty. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk.
Page 106 Troubleshooting Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Windows ME/2000: Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer.
Page 107: Specifications
Specifications General General Model Name SyncMaster P50FP SyncMaster P63FP PDP Panel Size SyncMaster 50 " Diagonal (127 cm) P50FP SyncMaster 63 " Diagonal (159 cm) P63FP Display area SyncMaster 1105.92 mm (H) x 622.08 mm (V) P50FP SyncMaster 1393.92 mm (H) x 784.08 mm (V) P63FP Pixel Pitch SyncMaster...
Page 108 Specifications Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Sold separately) Dimensions (W x H x D) / Weight SyncMaster P50FP 1204.6 x 724.1 x 97.1 mm ( 47.4 x 28.5 x 3.8 inch ) (Without Stand) 1204.6 x 773.2 x 362.4 mm ( 47.4 x 30.4 x 14.3 inch ) (With Stand) / 37.4 kg ( 82.5 lbs )
Page 109 Specifications Dot Acceptable For example, the number of PDP sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas.
Page 110: Preset Timing Modes
Specifications PowerSaver This PDP Display has a built-in power management system called PowerSaver. This system saves energy by switching your PDP Display to low-power mode when it has not been used for a certain amount of time. The PDP Display automatically returns to normal operation when you press a key on the keyboard.
Page 111 Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 800 x 600 37.879 60.317 40.000 VESA, 800 x 600 48.077 72.188 50.000 VESA, 800 x 600 46.875 75.000 49.500 VESA, 848 x 480 31.020 60.000 33.750...
Page 112: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP. •...
Page 113 Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use. • Turn the power off for 2 hours after 12 hours in use. • Set the Monitor to power off with the PC Display Properties Power Scheme. •...
Page 114: Select Method
Information • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes. • Every 30 minutes, change the characters with movement. • All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
Page 115 Information - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) •...
Page 116 Information • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble )
Page 117 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG http://www.samsung.com/mx (726-7864) Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar...
Page 118 022 - 607 - 93 - 33 PORTUGAL SAMSUNG http://www.samsung.com/pt (7267864) SLOVAKIA 0800-SAMSUNG(726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSU(902 172 http://www.samsung.com/es 678) SWEDEN 075 - SAMSUNG(726 78 64) http://www.samsung.com/se SWITZERLAND 0848 - SAMSUNG(7267864, http://www.samsung.com/ch CHF 0.08/min) 0845 SAMSUNG (7267864) http://www.samsung.com/uk ESTONIA 800-7267 http://www.samsung.ee LATVIA 8000-7267 http://www.samsung.com/lv...
Page 119 INDIA 3030 8282 http://www.samsung.com/in 1800 110011 1-800-3000-8282 INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800 SAMSUNG (0800 726 http://www.samsung.com/nz 786) PHILIPPINES 1800-10-SAMSUNG http://www.samsung.com/ph (726-7864) SINGAPORE 1800-SAMSUNG(726-7864) http://www.samsung.com/sg THAILAND 1800-29-3232 http://www.samsung.com/th 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn...
Page 120: Correct Disposal
This product should not be mixed with other commercial wastes for disposal. Authority Information in this document is subject to change without notice. © 2008 Samsung Electronics Co., Ltd. All rights reserved.
Page 121 Reproduction in any manner whatsoever without the written permission of Samsung Elec- tronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this ma- terial.

This manual is also suitable for:

Syncmaster p50fp

Samsung P63FP - 63" - Plasma Monitor User Manual

Quick Links

User Manual

Troubleshooting

Related Manuals for Samsung P63FP - 63" - Plasma Monitor

Summary of Contents for Samsung P63FP - 63" - Plasma Monitor

This manual is also suitable for:

Table of Contents