Cisco WS-SUP720-3B - Supervisor Engine 720 User Manual
Cisco WS-SUP720-3B - Supervisor Engine 720 User Manual

Cisco WS-SUP720-3B - Supervisor Engine 720 User Manual

Router supervisor engine and route switch processor
Table of Contents

Advertisement

Cisco 7600 Series Router
Supervisor Engine and
Route Switch Processor Guide
March 2012
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-10100-11

Advertisement

Table of Contents
loading

Summary of Contents for Cisco WS-SUP720-3B - Supervisor Engine 720

  • Page 1 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide March 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-10100-11...
  • Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
  • Page 3: Table Of Contents

    2-10 RSP720 with 10GE Uplink Ports 2-10 RSP720-10GE Features 2-11 Supported Chassis, Line Cards, and Modules 2-11 RSP720-10GE Usage Guidelines and Limitations 2-13 QoS on the RSP720-10GE 2-13 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 4 3-17 Troubleshooting Route Switch Processors and Supervisor Engines C H A P T E R Getting Started AC and DC Power Supply Information Chassis and Supervisor Slot Installation Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 5 B-12 DB-25 Adapter (for Connecting to a Terminal) B-12 Modem Adapter B-13 Console Port Mode 2 Signaling and Pinouts (Sup2 Only) B-13 RJ-45 Connector B-14 Fiber-Optic Connectors B-16 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 6 Cleaning the Fiber-Optic Connectors B-18 LX/LH GBIC and MMF Cable Considerations B-19 Patch Cord B-19 Patch Cord Configuration Example B-19 Patch Cord Installation B-20 N D E X Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 7: Contents

    Preface This guide describes the route switch processors and supervisor engines supported by Cisco 7600 series routers. It also provides technical specifications for these modules and describes cable and connector specifications. Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, Caution replace, or service the equipment described in this document.
  • Page 8: Document Organization

    Route Switch Processor 720. Beginning in Cisco IOS Release 12.2SRB1, eFSU and ISSU are supported on the RSP720, Sup720, and Sup32. Added a note that Cisco IOS Release 12.2SXF is the last release in which the Supervisor Engine 720 (with PFC3A) is supported. OL-10100-02...
  • Page 9: Document Conventions

    Statement 1071 SAVE THESE INSTRUCTIONS See Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for translations of warnings and information about the compliance and safety standards with which Cisco 7600 series routers conform.
  • Page 10: Related Documentation

    For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 11: Chapter 1 Cisco 7600 Product Overview

    C H A P T E R Cisco 7600 Product Overview This chapter provides an overview of the Cisco 7600 series routers and describes interface and port addresses on the routers. It contains the following sections: Cisco 7600 Series Routers, page 1-1 •...
  • Page 12: Supported Hardware

    Hot-swappable fan assembly • Redundant AC-input or DC-input power supplies • Redundant AC-input or DC-input power entry modules (PEMs) (Cisco 7603 and Cisco 7606 routers only) • An optional Switch Fabric Module (WS-X6500-SFM2) that is available with the Supervisor Engine 2. For redundancy, you can install a redundant SFM2 module. The module that is installed first functions as the primary module.
  • Page 13: Features

    Feature Description Performance For detailed information about the features supported on Cisco 7600 series routers, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for the configuration version of software being used on the router. Supervisor Modular, upgradable feature modules for core switching logic •...
  • Page 14 (standby) module Support for two redundant AC- or DC-input, load-sharing power supplies • Support for two redundant AC- or DC-input PEMs (Cisco 7603 and Cisco 7606 • routers only) Power management for modules and power supplies •...
  • Page 15 The Sup720 SP/RP, Sup32 RP, and Sup2 SP/RP contain 32-MB or 64-MB of • internal flash memory. Cisco IOS Release 12.2(18)SXF and later releases support the CF adapter as an orderable option (Cisco part number CF-ADAPTER=) for these Sups. In the command-line-interface (CLI), you access internal flash memory as Note bootdisk (CF adapter) or bootflash (non-CF adatper).
  • Page 16: Port Addresses

    • Port Addresses Each port (or interface) in the Cisco 7600 series router has several different types of addresses. The physical interface address is the actual physical location (slot and port) of the interface connector within the chassis. The system software uses the physical addresses to control activity within the router and to display status information.
  • Page 17: Mac Addresses

    Each VLAN in the spanning tree has one unique MAC address. This addressing scheme enables the router to identify the state (connected or not connected) of each interface. When you hot swap a module, the MAC address changes with the module. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 18: Supervisor Engine 2T

    • 2-Terabit aggregate bandwidth capacity. Providing 1Gbps/10Gbps and 40Gbps interface support for future customer bandwidth growth requirements. Security: Support for Cisco TrustSec, CTS, providing MacSec encryption and Role-Based ACL. • Providing control plane policing to address denial of service attacks.
  • Page 19: Chapter 2 Route Switch Processors And Supervisor Engines

    C H A P T E R Route Switch Processors and Supervisor Engines This chapter describes the route switch processors and supervisor engines supported on Cisco 7600 series routers and provides instructions for performing basic tasks on the modules. It contains the following sections: Overview, page 2-2 •...
  • Page 20: C H A P T E R 2 Route Switch Processors And Supervisor Engines

    • Supervisor Engine 32—Supported on all but the Cisco 7603 router. • Supervisor Engine 2—Supported on all but the Cisco 7613 router. The Supervisor Engine 2 is no • longer supported in Cisco IOS Release 12.2SRA and later releases. Supervisor Engine 2T —Supported on Cisco 7609-S routers, effective with Cisco IOS Release •...
  • Page 21 Runs Layer 2 and Layer 3 protocols, such as the Spanning Tree Protocol (STP) and others. – For information about supported protocols, see the Cisco 7600 Series Router Cisco IOS Software Configuration Guide and the release notes for the software version running on the router.
  • Page 22 Overview Table 2-1 lists the RSP and supervisor engine configurations supported on Cisco 7600 series routers. Specific combinations of processors and modules may not be supported in your chassis. See the release notes for your software version for information about supported combinations.
  • Page 23 1 GB) and two internal CompactFlash slots (one each for RP and SP, 512 MB default for each) • Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 24 Requires larger power supplies and a high-speed fan tray • QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t • Cisco IOS Release 12.2SXF is the last release in which the Note Sup720 with PFC3A is supported. WS-SUP720-3B Two Gigabit Ethernet uplink ports: port 1 supports a 1-Gbps SFP •...
  • Page 25 QoS port architecture (Rx/Tx): 1p1q4t/1p2q2t • Note A CompactFlash (CF) adapter with 512-MB bootdisk is available for Sup720 modules in Release 12.2(18)SXF and later releases. Use the Cisco part number CF-ADAPTER= for ordering. Supervisor Engine 32 WS-SUP32-GE-3B Nine Gigabit Ethernet uplink ports: eight SFP modules and one •...
  • Page 26 WS-X6500-SFM2 (Optional) SFM2 • Note The Sup2 is not supported in Cisco IOS Release 12.2SRA and later releases. Five uplink ports on Sup 2T: two 10GE and three 1GE. The two Supervisor Engine 2T • 10GE ports use x2 as transceiver and the three 1GE ports use SFP.
  • Page 27: Route Switch Processor 720

    This section describes the Route Switch Processor 720 (RSP720). The Cisco 7600 RSP720 consists of a full-size board and two integrated daughter cards: the MSFC4 and a PFC3C or PFC3CXL. The RSP720 has an integrated switch fabric that interconnects all of the line cards in the Cisco 7600 router with point-to-point 20-Gbps full-duplex serial channels.
  • Page 28: Supported Chassis, Line Cards, And Modules

    RSP720 with 10GE Uplink Ports Supported Chassis, Line Cards, and Modules The RSP720 supports the following Cisco 7600 chassis, line cards and modules: Supported on all Cisco 7600 routers (including enhanced chassis) except the Cisco 7603 and the • Cisco OSR-7609 •...
  • Page 29: Rsp720-10Ge Features

    (RP) with a default 2-GB memory for the 3CXL version and 1-GB for the 3C version. The switch processor (SP) ships with a default 1-GB memory. Memory options are available to upgrade to 4-GB memory on the RP. From Cisco IOS Release 12.2(33)SRD1 onwards, a 2-GB memory upgrade option is supported on the SP.
  • Page 30 For SRD4 release, two new commands are introduced for high availability feature. The commands are Note platform redundancy bias and show platform redundancy bias. For complete syntax and usage information for the commands, refer to the Cisco IOS High Availability Command Reference at this URL: http://www.cisco.com/en/US/docs/ios/ha/command/reference/ha_book.html The uplinks on the standby RSP720-10GE are not active.
  • Page 31: Rsp720-10Ge Usage Guidelines And Limitations

    For SRD4 release, a new command is introduced to prevent the QoS data getting reset during second Note pass lookup over internal vlans for the mvpn case. For complete syntax and usage information for the command mls qos recirc untrust, refer to the Cisco QoS command reference at this URL: http://www.cisco.com/en/US/docs/ios/qos/command/reference/qos_book.html...
  • Page 32 • Configuring 10GE Only QoS Cisco IOS Release 12.2SRC introduces a new command to enable QoS features on 10GE uplink ports only. By default, the router runs in mixed mode, which means that QoS is enabled on both the 10GE uplink ports and the 1GE uplink ports.
  • Page 33: Supervisor Engine 2T

    1GE ports use SFP. The uplink ports are configurable with SFP or X2 optics modules. See the “Connecting to the Uplink Ports” section on page 3-10 for more information. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-15 OL-10100-11...
  • Page 34 Orange The port is disabled. Flashing The port is bad. orange The supervisor engine is powering up or the port is enabled and there is no link. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-16 OL-10100-11...
  • Page 35: Primary Supervisor Engine 2T Components

    These include routing protocol support, Layer 2 protocols (for example, Spanning Tree Protocol and VLAN Trunking Protocol), and security services. The MSFC5 builds the Cisco Express Forwarding information base (FIB) table in software and then downloads this table to the hardware application-specific-integrated circuits (ASICs) on the PFC4 and Distributed Forwarding Card 4 (DFC4), if present on a module, which make the forwarding decisions for IP unicast and multicast traffic.
  • Page 36 64 rates Layer 2 rate limiters 20 ingress/6 egress 20 ingress/6 egress MAC ACLs featuring per-port/per VLAN granularity Distributed policers Shared uFlow policers Egress uFlow policers Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-18 OL-10100-11...
  • Page 37 TTL) CoPP exceptions Netflow support ACL labels Port ACL ACL dry run Hitless ACL changes Table 2-7 shows the MPLS and virtualization features for Supervisor Engine 2T. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-19 OL-10100-11...
  • Page 38 Native L2 over multipoint VRF-aware operational contexts VPN Netflow support VPN aware NAT VRF-lite scalability VLAN reuse per VLAN reuse per sub-interface sub-interface Per VPN interface statistics Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-20 OL-10100-11...
  • Page 39: Supervisor Engine 720 And Supervisor Engine 32

    Front-Panel Controls (RSP720, RSP720-10GE, Sup720, Sup32) Table 2-8 describes the front-panel controls on the Route Switch Processor 720 and RSP720-10GE, the Supervisor Engine 720, and the Supervisor Engine 32. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-21 OL-10100-11...
  • Page 40: Front-Panel Leds (Rsp720, Rsp720-10Ge, Sup720, Sup32)

    The module is powering up or a minor hardware fault has occurred. Major hardware problem. The temperature of the supervisor engine or RSP has exceeded the major temperature threshold. Blinking Continuous backplane stall. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-22 OL-10100-11...
  • Page 41: Supervisor Engine 2

    Table 2-11 describes the LEDs. Note In Cisco IOS Release 12.2SR and later releases, the Supervisor Engine 2 is no longer supported on Cisco 7600 series routers. Figure 2-7 Supervisor Engine 2 Front Panel...
  • Page 42 Diagnostic test failed; the module is not operational. (The fault occurred during the initialization sequence.) An overtemperature condition has occurred. (A major threshold has been exceeded during environmental monitoring.) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-24 OL-10100-11...
  • Page 43 2. VTT = voltage termination. The VTT module terminates signals on the system switching bus. 3. If no redundant supervisor engine is installed and there is a VTT module minor or major overtemperature condition, the system shuts down. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-25 OL-10100-11...
  • Page 44 Chapter 2 Route Switch Processors and Supervisor Engines Supervisor Engine 2 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 2-26 OL-10100-11...
  • Page 45: Preparing For Installation Or Removal

    Determine which chassis slot to install the module in. (See the “Determining Module Location” section on page 3-3.) Consider cabling for the console and uplink ports. (See Appendix B, “Cable and Connector • Specifications.”) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 46: C H A P T E R 3 Installing And Configuring Route Switch Processors And Supervisor Engines

    Place a removed component board-side-up on an antistatic surface or in a static-shielding container. • If you plan to return the component to the factory, immediately place it in a static-shielding container. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 47: Tools Required For Module Installation

    Periodically check the resistance value of the antistatic strap. The measurement should be within the Caution range of 1 and 10 megohms (Mohms). Tools Required for Module Installation These tools are required to install modules in the Cisco 7600 series router: Flat-blade screwdriver • Antistatic wrist strap or other grounding device •...
  • Page 48: Installing A Supervisor Engine Or Route Switch Processor

    Fully open both ejector levers on the new module. (See Figure 3-1.) Step 3 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 49 4 PORT OC-12 POS SM PORT MODE PORT 1 CONSOLE SUPERV ISOR2 PORT 2 PCMCIA EJECT OSM-4OC1 2 POS-SI 4 PORT OC-12 POS SM EMI gasket Ejector lever fully extended Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 50 Make sure the ejector levers are fully closed before tightening the captive installation screws. Note Blank module filler plates (Cisco part number 800-00292-01) should be installed in any empty chassis Note slots to keep dust out of the chassis and to maintain consistent airflow through the chassis.
  • Page 51: Removing A Supervisor Engine Or Route Switch Processor

    Place the module on an antistatic mat or antistatic foam, or immediately reinstall the module in another slot. Step 6 Install blank module filler plates (Cisco part number 800-00292-01) in any empty slots to keep dust out Step 7 of the chassis and to maintain consistent airflow through the chassis.
  • Page 52: Hot Swapping (Oir) Modules

    Hot Swapping (OIR) Modules Hot Swapping (OIR) Modules Cisco 7600 series routers provide a feature that allows you to remove and replace a redundant supervisor engine or route switch processor (and other redundant cards) without powering down the router. This feature, called hot swapping or online insertion and removal (OIR), allows you to remove and replace a redundant module without disrupting router operation.
  • Page 53: Connecting To The Console Port

    The console port is an EIA/TIA-232 asynchronous, serial connection with hardware flow control and an RJ-45 connector. The accessories kit that is shipped with your Cisco 7600 series router contains the necessary cable and Note adapters to connect a terminal or modem to the console port. See the “Console Port Signals and Pinouts”...
  • Page 54: Connecting A Modem

    Do not remove the plugs from the optical bores on the fiber-optic cable or the module port or until you Caution are ready to connect the cable. The plugs protect the optical bores and cable from contamination. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-10 OL-10100-11...
  • Page 55 Insert the cable connector into the uplink port and make sure that both the transmit (Tx) and receive (Rx) Step 4 fiber-optic cables are fully inserted into the connector. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-11 OL-10100-11...
  • Page 56: Using Flash Memory Cards

    • In Cisco IOS Release 12.2SRC, the uplink ports on a standby RSP720-10GE are not active and cannot be used for normal traffic. Using Flash Memory Cards The front panel on the supervisor engine or route switch processor has one or two disk slots for flash memory cards.
  • Page 57: Installing A Flash Memory Card

    Using Flash Memory Cards Not all flash memory cards have a write-protection switch. Note Table 3-3 lists the Cisco product numbers of memory cards supported on Cisco 7600 supervisor engines and route switch processors. Table 3-3 CompactFlash Memory Cards Product Number...
  • Page 58: Removing A Flash Memory Card

    Cisco IOS software requirements for the hardware installed on your router. You must have an account on Cisco.com to access the Feature Navigator or Software Advisor tool. Note To determine which software features are supported by your route switch processor or supervisor •...
  • Page 59 3-6. SP has one DIMM slot and RP processor has two DIMM slots. Slot 1 and 2 are for the RP processor. Slot 3 is for the SP processor. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-15 OL-10100-11...
  • Page 60 You have to remove the RSP from the chassis for DIMM upgrade. Save all your configurations before you remove the RSP. Always use an ESD wrist strap when handling the RSP or coming in contact with internal components. Caution Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-16 OL-10100-11...
  • Page 61: Configuring A Supervisor Engine Or Route Switch Processor

    Step 4 Configuring a Supervisor Engine or Route Switch Processor See the Cisco 7600 Series Router Cisco IOS Software Configuration Guide for information about how to configure the supervisor engine or route switch processor for operation. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide...
  • Page 62 Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines Configuring a Supervisor Engine or Route Switch Processor Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 3-18 OL-10100-11...
  • Page 63: Chapter 4 Troubleshooting Route Switch Processors And Supervisor Engines

    4500W, and if only 2 inputs are connected, the output is 3000W. However, if only one input is connected, 6000W Power supply output fails. The green LED indicates the DC power supply for all the power inputs. For more information on the various LED status, Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide at http://www.cisco.com/en/US/docs/routers/7600/Hardware/Hardware_Guides/Supervisor_Engine_and_...
  • Page 64: Chassis And Supervisor Slot Installation

    RSP720-1GE Supported Hardware and Features The RSP720 supports the following Cisco 7600 chassis, line cards and modules: Supported on all Cisco 7600 routers (including enhanced chassis) except the Cisco 7603. At present • 7603 is discontinued and only 7603S is shipped.
  • Page 65: Rsp720-10Ge Supported Chassis, Line Cards, And Modules

    RSP720-10GE does not support High Availability features in 12.2(33)SRC and 12.2(33)SRD. Obtaining Technical Assistance If you are unable to solve a problem on your own based on the solutions provided, consult a Cisco customer service representative for assistance. When you call, ensure that you have the following information: •...
  • Page 66: Troubleshooting Supervisor Failures

    If you insert the DIMMs in both the slots for RP upgrade, and card does not initiate, then swap the DIMMs between the two slots and check again. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 67: Troubleshooting Back-Plane Data Corruption During Oir Of A Rp

    If a c7600 line card module experiences issues, follow these instructions. Leave the card in its impaired state to allow the Cisco TAC and escalation teams to collect additional information before resetting the card. If you are unable to leave the card in the impaired state, the card may ultimately need to be reset, but some minimal data should be collected before reloading the card.
  • Page 68 *Feb 22 09:27:43.149: %C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (admin request) 7600(config)#power enable module 4 *Feb 22 09:39:23.071: %DIAG-SP-6-BYPASS: Module 4: Diagnostics is bypassed *Feb 22 09:39:25.622: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are now online Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 69: Troubleshooting Interface Down Issues

    Tracebacks provide useful information to debug and fix problems. Tracebacks appear when a spurious memory access, alignment error, crash or memory corruption occurs. This is a sample traceback message: -Traceback 4018C538 4018A2A4 40338858 4034FDD0 403480B0 4017BC40 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 70: Troubleshooting Image Reload Issues

    The solution is to load a tftp://171.69.17.19/tftpboot/kapilk/nightly default image first and then do reload netboot. /Fri/s72033-jsv-mz Copying tftp://171.69.17.19/tftpboot/kapilk/nightly /Fri/s72033-jsv-mz to sup-image:0 %Error opening sup-image:0 (Unknown error Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 71: Troubleshooting Supervisor 2T

    Troubleshooting Catalyst 6500/6000 Series Switches Running CatOS on the Supervisor Engine and Cisco IOS on the MSFC at the following URL: http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008015504b. shtml Hardware Requirements for Catalyst 6000/Catalyst 6500 Redundancy at the following URL: • http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a00800a2cee. shtml Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 72 Chapter 4 Troubleshooting Route Switch Processors and Supervisor Engines Troubleshooting Supervisor 2T Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide 4-10 OL-10100-11...
  • Page 73: Appendix

    A P P E N D I X Technical Specifications This appendix provides the technical specifications for the Cisco 7600 route switch processors and supervisor engines. Module Specifications Table A-1 lists the environmental and physical specifications for the Cisco 7600 route switch processors (RSPs) and supervisor engines.
  • Page 74: Appendix A Technical Specification

    Appendix A Technical Specifications Regulatory Standards Compliance Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 75: Appendix

    A P P E N D I X Cable and Connector Specifications This appendix lists the cable and connector specifications for the Cisco 7600 route switch processors (RSPs) and supervisor engines. It contains the following information: Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics, page B-2 •...
  • Page 76: A P P E N D I X B Cable And Connector Specifications

    Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Supported Dense Wave Division Multiplexing (DWDM) Wavelength Optics Table B-1 lists the DWDM small form-factor pluggables (SFP) to RSP 720 and RSP 720-10GE: Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 77 Transceiver Module Part Numbers RSP720 and DWDM-SFP-3346 RSP720-10GE DWDM-SFP-3739 DWDM-SFP-4134 DWDM-SFP-4532 DWDM-SFP-4931 DWDM-SFP-5332 DWDM-SFP-5736 DWDM-SFP-6141 DWDM-SFP-6061 DWDM-SFP-5979 DWDM-SFP-5898 DWDM-SFP-5817 DWDM-SFP-5655 DWDM-SFP-5575 DWDM-SFP-5494 DWDM-SFP-5413 DWDM-SFP-5252 DWDM-SFP-5172 DWDM-SFP-5092 DWDM-SFP-5012 DWDM-SFP-4851 DWDM-SFP-4772 DWDM-SFP-4692 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 78: Supported Coarse Wave Division Multiplexing (Cwdm) Wavelength Optics

    CWDM small form-factor pluggables (SFP) to RSP 720 and RSP 720-10GE: Table B-2 Supported CWDM Wavelength Optics Supervisor Engine or RSP Transceiver Module Part Numbers RSP720 and CWDM-SFP-1470 RSP720-10GE CWDM-SFP-1490 CWDM-SFP-1510 CWDM-SFP-1530 CWDM-SFP-1550 CWDM-SFP-1570 CWDM-SFP-1590 CWDM-SFP-1610 Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 79: Limiting Connection Distances

    RSP720-10GE X2-10GB-SR X2-10GB-LR X2-10GB-ER X2-10GB-LX4 X2-10GB-CX4 X2-10GB-LRM X2 10GB-ZR 1GE Uplink Ports: GLC-SX-MM GLC-LH-SM GLC-ZX-SM GLC-T GLC-BX-D GLC-BX-U SFP-GE-S SFP-GE-L SFP-GE-T Supervisor Engine 720 GLC-SX-MM GLC-LH-SM GLC-ZX-SM GLC-T Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 80: 1Ge Uplink Ports And Cabling Specifications

    Supervisor Engine 2 1000BASE-X GBIC modules, which are preinstalled 1GE Uplink Ports and Cabling Specifications Table B-4 describes the 1GE SFP transceiver modules that are used for Cisco 7600 uplink ports. Table B-5 provides cabling specifications. Note Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector for the RSP720-10GE.
  • Page 81 1640 ft (500 m) 1804 ft (550 m) GLC-LH-SM 1300 62.5 1804 ft (550 m) 1804 ft (550 m) SFP-GE-L 1804 ft (550 m) 9/10 — 6.2 mi (10 km) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 82: 10Ge Uplink Ports And Cabling Specifications

    10GBASE-CX4 X2 or XENPAK transceiver module for CX4 copper cable, Infiniband 4X connector XENPAK-10GB-CX4 X2-10GB-LRM 10GBASE-LRM X2 transceiver module for MMF, dual SC connector X2-10GB-ZR Cisco 10GBASE-ZR X2 transceiver module for SMF, dual SC connector Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 83: Gbic Module Cabling Specifications

    Converter (GBIC) modules installed in the Supervisor Engine 2. All GBIC interfaces have SC connectors, and the minimum cable distance for all GBICs listed (MMF and SMF) is 6.5 feet (2 meters). Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide OL-10100-11...
  • Page 84: Console Port Cabling Specifications And Pinouts

    The console port, which is located on the front panel of the supervisor engine or route switch processor, provides access to the Cisco 7600 router. The following sections provide information about the console port cabling specifications and the port’s signals and pinouts.
  • Page 85: Console Port Signals And Pinouts

    B-1.) If you purchased your cable from Cisco Systems, pin 1 is white on one connector, and pin 8 is white on the other (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).
  • Page 86: Adapter (For Connecting To A Pc

    RJ-45-to-DB-25 Terminal Console Console Port RJ-45-to-RJ-45 Rollover Cable Adapter Device Signal RJ-45 Pin RJ-45 Pin DB-25 Pin Signal 1. Pin 1 is connected internally to Pin 8. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-12 OL-10100-11...
  • Page 87: Modem Adapter

    2 (DTR) Output 3 (RxD) Input 4 (GND) 5 (GND) 6 (TxD) Output 7 (DSR) Input 8 (CTS) Input 1. Pin 1 is connected internally to Pin 8. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-13 OL-10100-11...
  • Page 88: Rj-45 Connector

    1 (RD+) 3 (TD+) 2 (RD–) 6 (TD–) 3 (TD+) 1 (RD+) 6 (TD–) 2 (RD–) 4 (Not used) 4 (Not used) 5 (Not used) 5 (Not used) Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-14 OL-10100-11...
  • Page 89 2 TP0- 2 TP0- 3 TP1+ 3 TP1+ 6 TP1- 6 TP1- 4 TP2+ 4 TP2+ 5 TP2- 5 TP2- 7 TP3+ 7 TP3+ 8 TP3- 8 TP3- Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-15 OL-10100-11...
  • Page 90: Fiber-Optic Connectors

    Always clean fiber connectors before installing them. For fiber-optic connector cleaning instructions, see the “Cleaning the Fiber-Optic Connectors” section on page B-18. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-16 OL-10100-11...
  • Page 91 The small form-factor pluggable (SFP) tranceiver modules used on the Supervisor Engine 720, Route Switch Processor 720, and RSP720-10GE uplink ports use either MT-RJ connectors or LC connectors depending on the SFP module vendor. Figure B-7 shows an LC connector. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-17 OL-10100-11...
  • Page 92: Cleaning The Fiber-Optic Connectors

    Blow dry the connectors with canned, dry, oil-free, compressed air. Step 2 Use a magnifying glass or inspection microscope to inspect the ferrule. If contaminants are visible, Step 3 repeat the cleaning procedure. Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-18 OL-10100-11...
  • Page 93: Lx/Lh Gbic And Mmf Cable Considerations

    984 feet (300 meters), a mode-conditioning patch cord is required. You must install the patch cord (Cisco product number CAB-GELX-625 or equivalent) between the GBIC and the MMF cable on both the transmit and receive ends of the link.
  • Page 94: Patch Cord Installation

    “To Cable Plant” into the patch panel. The patch cord is 9.84 feet (3 meters) long and has duplex SC male connectors at each end. Figure B-9 Patch Cord Installation To equipment To cable plant Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide B-20 OL-10100-11...
  • Page 95 2 signaling (Sup Eng 2) console port copy running-config command console ports Gigabit Ethernet limitations 7, 9, 10 specifications category 5e static electricity caution DB-25 adapter category 6 static electricity caution Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-1 OL-10100-11...
  • Page 96 16, 22, 24 Sup2 16, 24 SWITCH LOAD (Sup Eng 2 only) GBICs, connecting to SYSTEM 16, 22, 25 Gigabit Ethernet cables 7, 9, 10 LINK LED Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-2 OL-10100-11...
  • Page 97 LX/LH GBICs Route Switch Processor 720 (RSP720) PCMCIA CompactFlash support See also Flash PC cards front panel (figure) PCMCIA flash file system Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-3 OL-10100-11...
  • Page 98 LEDs (table) 16, 24 write-protection switch, flash memory card (figure) uplink ports WS-X6380-NAM Supervisor Engine 32 (Sup32) CompactFlash support front panel (figure) front panel controls Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide IN-4 OL-10100-11...

This manual is also suitable for:

7604760676137600 series

Table of Contents