Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fujitsu MHX2300BT - Mobile 300 GB Hard Drive
Summary of Contents for Fujitsu MHX2300BT - Mobile 300 GB Hard Drive
-
Page 1: Chapter 3 Installation Conditions
CHAPTER 3 Installation Conditions Dimensions Mounting Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E254... - Page 2 Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. The PCA and connectors are not included in these dimensions. Dimension from the center of the user tap to the base of the connector pins Length of the connector pins Dimension from the outer edge of the user tap to the center of the connector pins...
- Page 3 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal Ground (SG).
- Page 4 Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Side surface mounting Bottom surface mounting Frame of system cabinet Frame of system cabinet 3.0 or less Screw Screw 3.0 or less Details of A...
- Page 5 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block.
- Page 6 Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from exceeding 60 °C.
- Page 7 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Mounting screw hole Mounting screw hole Cable connection Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers.
- Page 8 Installation Conditions General notes ESD mat Wrist strap Shock absorbing mat Use the Wrist strap. Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not hit HDD each other. Do not stack when carrying. Do not place HDD vertically Do not drop.
-
Page 9: Connections With Host System
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors Figure 3.7 Connector locations C141-E254... -
Page 10: Connector Specifications For Host System
Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the SATA interface connector and pin numbers. View from the connector side Power supply Signal segment segment View from the PCA side S1 pins in the signal P1 pins in the power segment supply segment... -
Page 11: Note About Sata Interface Cable Connection
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector... - Page 12 This page is intentionally blank. left...