Related Manuals for Chamberlain LiftMaster TAC1
Summary of Contents for Chamberlain LiftMaster TAC1
- Page 1 TAC1 Telephone Entry System Installation and Programming Manual The Chamberlain Group 845 Larch Ave. Elmhurst, IL 60126-1196 www.liftmaster.com...
-
Page 2: Table Of Contents
Test the Gate/Door Relays Dimensions Test the Telephone Connections Carton Inventory PROGRAMMING 13-19 INSTALLATION 4-11 From the TAC1 Keypad Mount the Back Panel Code Setup Description of the Processor Board Code Operation Overview of Telco Wiring From the Telephone 15-16... -
Page 3: Specifications
SPECIFICATIONS >> CABLE REQUIREMENTS, DIMENSIONS AND CARTON INVENTORY CABLE REQUIREMENTS Outdoor installations require shielded cable. Non-shielded cable can be used for indoor installations ONLY. PROCESSOR BOARD WIRE TYPE RECOMMENDATIONS From the power transformer at 120 Vac outlet 2 - Conductor Cable Shielded Only - See Power Wire Table Below From the door strike, maglock or gate operator 2 - Conductor Cable... -
Page 4: Installation
(hardware not provided) with the top of the panel up. IMPORTANT NOTE: Both the back panel and TAC1 unit must be oriented and mounted in the upright position as shown at right and on the installation warning label. -
Page 5: Overview Of Telco Wiring
INSTALLATION >> OVERVIEW OF TELCO WIRING Many phone companies have updated their color standards due to Notes about wire connectors the use of Cat 5 cable for most phone line installs, and keep (terminal blocks): residential and business installs in line with each other. In the new •... -
Page 6: Wiring The Unit With A Telco Line
INSTALLATION >> WIRING THE UNIT WITH A TELCO LINE AND WIRING THE UNIT WITHOUT A TELCO LINE Never run data wires and high voltage wires in the same conduit. The high voltage wires may interfere with the data wires and cause the system to malfunction. WIRING THE UNIT WITH A TELCO LINE Ringer Equivalence Number (REN) = 5 RING... -
Page 7: Wiring A Gate Operator (Normally Open)
INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) AND WIRING AN AUTO-CALL SENSOR WIRING A GATE OPERATOR (NORMALLY OPEN) The gate operator can be connected to Relay 1 or Relay 2. See the Notes about wire connectors Programming section for information about configuring Relays 1 (terminal blocks): and 2. -
Page 8: Wiring A Gate Operator (Normally Open)
INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) A DOOR STRIKE LOCK (NORMALLY OPEN) AND WIRING A GATE OPERATOR (NORMALLY OPEN) & A MAGLOCK (NORMALLY CLOSED) WIRING A GATE OPERATOR (NORMALLY OPEN) & A DOOR STRIKE LOCK (NORMALLY OPEN) The door strike can be connected to Relay 1 or Relay 2. See the Notes about wire connectors Programming section for information about configuring Relays 1 (terminal blocks):... -
Page 9: Wiring A Door Strike Lock (Normally Open)
INSTALLATION >> WIRING A DOOR STRIKE LOCK (NORMALLY OPEN) AND WIRING A MAGLOCK (NORMALLY CLOSED) WIRING A DOOR STRIKE LOCK (NORMALLY OPEN) The door strike can be connected to Relay 1 or Relay 2. See the Notes about wire connectors Programming section for information about configuring Relays 1 (terminal blocks): and 2. -
Page 10: Earth Ground Rod
Connect the transformer into a 110 Vac outlet after all connections have been made, any other type of outlet will cause 12 Vac Power (included) damage to the system. POWER WIRE TABLE The TAC1 MUST be grounded. DISTANCE AC POWER WIRE SIZE Under 30 feet... -
Page 11: Plug The Transformer Into The Outlet
Check the Power LED is illuminated. POWER NOTE: Once power is applied, the TAC1 will begin to click to indicate that it is powered, and is waiting to be programmed for the unit’s Master Code. The Master Code is used to unlock the programming functions of the TAC1. -
Page 12: Testing
3. To test Relay 1 have someone answer the telephone and enter Call Button “*9” (Star + 9). The TAC1 will disconnect the call as soon as the relay is activated. To test Relay 2 have someone answer the telephone and enter “*5” (Star + 5). The TAC1 will... -
Page 13: Programming
PROGRAMMING >> FROM THE TAC1 KEYPAD GENERAL INSTRUCTION NOTE: Use the STAR Key “*” to cancel any input. PROGRAMMING INSTRUCTION SYNTAX KEYSTROKES General Programming Master Code + Command 1234 + 1 (12,123) Code Programming Master Code + Command + Code... -
Page 14: Code Setup
1. Enter the Master Code: 1. Enter the Master Code: 2. Enter the Program Code: To disengage party mode: Enter a valid code into the TAC1 2. Enter the Program Code: keypad or enter “*9” into the local telephone. TRIGGER RELAY 2 AND CHANNEL 2 ENGAGE PARTY MODE (RELAY 2) 1. -
Page 15: From The Telephone
PROGRAMMING >> FROM THE TELEPHONE TELEPHONE PROGRAMMING ADJUST “PICK UP” RING COUNT ENABLE INTERCOM MODE Enter the command tone: 1. Enter the command tone: 2. Enter the ring count: through ENABLE TELCO MODE Enter the command tone: ENABLE ALTERNATE DTMF PROGRAMMING This feature changes the first programming digit from ENABLE STANDARD (LONG) RING TONE Enter the command tone:... -
Page 16: Telephone Commands
TAC1 will automatically return to the telco line. PROGRAM A PRE-INSTALLED LIFTMASTER RECEIVER When either of the relays is activated the TAC1 will emit a 315 MHz signal to the receiver. 1. Locate the receiver. Refer to the gate or door operator manual for information about the location of the learn button. -
Page 17: Quick Reference
Adjust Relay Output Time .5 seconds Master Code (4 digits) + 025 + Relay Output Time (0000-8000 (Relay 2) seconds) NOTE: Relay output time is ALWAYS 4 digits. DIRECT COMMANDS FROM THE TAC1 KEYPAD KEYSTROKES ACTION User Code + 1 Triggers Relay 1... - Page 18 PROGRAMMING >> QUICK REFERENCE TELEPHONE PROGRAMMING PROGRAMMING NUMBER DESCRIPTION OF TASK FACTORY SETTING PROGRAMMING PROCEDURE **01 Enable Call Forwarding Disabled **01 **02 Disable Call Forwarding **02 **03 Enable Intercom Mode Disabled **03 **06 Verify Call Forwarding Number Disabled **06 (Via Caller ID) **07 Enable Telco Mode Disabled...
-
Page 19: Tac1 Master Code
TAC1 MASTER CODE Write down the Master Code and store in a secure location. -
Page 20: Limited Warranty
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-2806 www.liftmaster.com NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.