Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR SHORT THROW PROJECTOR
WALL MOUNTING BRACKET FOR USE WITH SHARP PROJECTOR
MODEL NOS. PG-F267X, PG-D2870W
COLOR: WHITE
TEL: 516-546-2272 FAX: 516-623-7766 TOLL FREE: 1-800-866-1820
AVDEX CORPORATION
115 HENRY STREET, FREEPORT, NY 11520
E-MAIL: SECURITY@AVDEX.COM
MODEL AN-STWM20
AN-STWM20 SHORT THROW
WALL MOUNTING BRACKET
WITH EXTENSION
Advertisement
Summary of Contents for Avdex PG-D2870W
- Page 1 MODEL AN-STWM20 INSTALLATION INSTRUCTIONS FOR SHORT THROW PROJECTOR WALL MOUNTING BRACKET FOR USE WITH SHARP PROJECTOR MODEL NOS. PG-F267X, PG-D2870W AN-STWM20 SHORT THROW WALL MOUNTING BRACKET WITH EXTENSION COLOR: WHITE AVDEX CORPORATION 115 HENRY STREET, FREEPORT, NY 11520 TEL: 516-546-2272 FAX: 516-623-7766 TOLL FREE: 1-800-866-1820...
-
Page 2: Installation Instructions
THAT ALL THE WORK IS DONE IN COMPLIANCE WITH NEC AND ALL LOCAL BUILDING AND SAFETY CODES. SAVE THIS BOOKLET AFTER THE INSTALLATION IS COMPLETED. THE ACCESSORIES REFERRED TO IN THESE INSTRUCTIONS ARE INTENDED FOR USE ONLY WITH COMPATIBLE SHARP PROJECTORS. SEE SHARP PROJECTOR OWNER’S MANUAL OR SHARP DEALER TO DETERMINE SUITABILITY. - Page 3 LOCATION OF THE WALL MOUNTING BRACKET Please refer to the owner’s manual for your SHARP LCD PROJECTOR for information which will help you to determine the best location for the placement of the wall mounting bracket assembly.
- Page 4 SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS STEP 1. ATTACH THE MOUNTING ASSEMBLY TO THE BOTTOM OF THE PROJECTOR. Place the flat surface of the 4 1/4” x 5 3/8” plate against the bottom of the Projector with the “U” shaped cut out toward the rear of the projector. See Fig.
- Page 5 SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS FIG. 3 WALL MOUNTING PLATE MOUNT ONTO WALL USING HEX HEAD BOLTS CABLE MANAGEMENT ACCESS PROVIDED Note that the mounting plate has a rectangular hole intended to facilitate wire and cable management if the wiring is fed through the wall.
- Page 6 SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS Tighten the button head screws on both sides of the extension tube after you have set the desired length. See Figure 5. STEP 3. HANG THE PROJECTOR Hang the projector on the long inner slide tube by sliding the rectangular sleeve over the long tube. Slide the sleeve forward over the long tube to the desired position and secure it with the two knobs on either side of the sleeve.
- Page 7 SHORT THROW PROJECTOR WALL MOUNTING BRACKET AN-STWM20 INSTALLATION INSTRUCTIONS SHORT THROW PROJECTOR WALL MOUNTING BRACKET WITH PROJECTOR MOUNT ASSEMBLY SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE A. From bottom of extension tube to top of projector 5” B. From bottom of extension tube to center of lens 7 1/4” C.
-
Page 8: One-Year Limited Warranty
ONE YEAR LIMITED WARRANTY AVDEX Corporation warrants to the first end use purchaser, that this AVDEX brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product or part thereof at no charge to the purchaser for parts or for labor, excluding costs of removal and/or installation, for one year from date of purchase.