Dell Latitude ST Owner's Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Tablet
  5. Latitude ST
  6. Owner's manual
Dell Latitude ST Owner's Manual

Dell Latitude ST Owner's Manual

Owner's manual
Hide thumbs Also See for Latitude ST:
Table of Contents

Advertisement

Quick Links

See also: Setup and Features Information , Setup Manual
Enlarged version
Dell Latitude ST
Owner's Manual
Regulatory Model: T02G
Regulatory Type: T02G001

Advertisement

Table of Contents
loading

Related Manuals for Dell Latitude ST

Summary of Contents for Dell Latitude ST

  • Page 1 Dell Latitude ST Owner's Manual Regulatory Model: T02G Regulatory Type: T02G001...

  • Page 2: Notes, Cautions, And Warnings

    Information in this publication is subject to change without notice. © 2011 Dell Inc. All rights reserved. Printed in the U.S.A. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell...

  • Page 3: Table Of Contents

    Contents Notes, Cautions, and Warnings....................2 1 Working on Your Computer.......................7 ........................7 Before Working Inside Your Computer ..............................8 Recommended Tools ............................8 Turning Off Your Computer ........................8 After Working Inside Your Computer 2 Overview............................9 ...................................9 Interface ................................10 Pen Overview ..............................10 Pen Information ..............................10 Calibrating The Pen .....................11...
  • Page 4 8 Removing The Battery......................27 ..............................28 Installing The Battery 9 Removing The Wireless Local Area Network (WLAN) Card..........29 ...................30 Installing The Wireless Local Area Network (WLAN) Card 10 Removing The Wireless Wide Area Network (WWAN) Card..........31 ..................32 Installing The Wireless Wide Area Network (WWAN) Card 11 Removing The Internal Storage Device (Solid State Drive)..........33 ..................33 Installing The Internal Storage Device (Solid State Drive)
  • Page 5 Enhanced Pre-boot System Assessment (ePSA) ........................55 Running The ePSA Diagnostic Utility ................................57 Beep Codes ..............................57 LED Error Codes ..........................58 N-trig Digitizer Troubleshooting .......................58 Installation IssuesTroubleshooting Steps: ....................58 Performance issuesTroubleshooting Steps: ....................59 Performance issuesTroubleshooting Steps: 22 Technical Specifications.......................61 23 Getting Help..........................65 ...............................65 Contacting Dell...

  • Page 7: Working On Your Computer

    Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

  • Page 8: Recommended Tools

    After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.

  • Page 9: Overview

    The Dell Latitude ST is built to be thin and light to match the mobility needs of executives, sales managers, doctors, and students alike. This allows the product to function as a primary system during short business trips, sales calls, etc. It was designed from the ground up to be managed similarly to how notebooks, desktops and workstations are managed today.

  • Page 10: Pen Overview

    The Latitude ST uses a specifically designed electrostatic pen or stylus for use in tablet PC mode. Instead of relying on battery power, the energy source for the stylus is magnetic energy produced by the excitation coil built into the digitizer itself.

  • Page 11: Removing / Inserting The Stylus Battery And Pen Tip

    To remove the pen tip, hold the pen tip and pull it out from the stylus. Install a new pen tip on the stylus pen head. Electronic Pen Usage The Latitude ST uses several input devices. The standard external USB keyboard and mouse are present, plus you can opt for the electrostatic pen or just use your finger as an input device.

  • Page 12: Tablet Pc Input Panel

    Tablet PC Input Panel When an application does not directly support pen input, you can use the Tablet PC Input Panel to enter text into your application. If you tap in an editable area, the Tablet PC Input Panel icon appears. Tapping the icon makes the Input Panel slide out from the edge of the display.

  • Page 13: Pen Flicks

    Icon Name Function Touch The touch keyboard is like a standard keyboard, but you enter text by tapping the keys keyboard with your tablet pen or finger. The writing pad and the character pad have a number pad, a symbol pad, and web quick keys to help you quickly and accurately enter these types of text.

  • Page 14: Touch Usage

    Touch Usage One of the key advantages of the Tablet PC is the ability to easily switch from pen input to touch input. When you use Touch Mode , a translucent image of a computer mouse, called the touch pointer, floats beneath your finger.

  • Page 15: Docking Station

    Docking Station The docking station is designed for Latitude ST. The docking station can be purchased separately from dell.com. For more information, see the docking station setup guide available on support.dell.com.
  • Page 16 Figure 1. Docking Station Front View 1. Dock Connector 2. Power LED Figure 2. Docking Station Back View 1. AC Adapter Connector 2. USB 2.0 Connector (1) 3. USB 2.0 Connector (2) 4. Network Connector (RJ45) 5. HDMI Connector 6. Audio Connector...

  • Page 17: Removing The Sd Memory Card

    Removing The SD Memory Card Follow the procedures in Before Working On Your Computer. Press in on the SD memory card to release it from the computer. Slide the SD memory card out of the computer. Installing The SD Memory Card Push the memory card into the compartment until it clicks into place.

  • Page 19: Removing The Digitizer Pen

    Removing The Digitizer Pen Follow the procedures in Before Working On Your Computer. Press in on the digitizer pen to release it from the computer. Pull the digitizer pen out of the computer. Installing The Digitizer Pen Push the digitizer pen into the compartment until it clicks into place. Follow the procedures in After Working Inside Your Computer.

  • Page 21: Removing The Label Door

    Removing The Label Door Follow the procedures in Before Working On Your Computer. Press the release latch that secures the label door. Lift up the label door diagonally and remove it from the computer. Installing The Label Door Place the label door diagonally and align it with the securing clips on the edges. Push the edges of the label door until it clicks into place.

  • Page 23: Removing The Sim Card

    Removing The SIM Card Follow the procedures in Before Working On Your Computer. Remove the label door. Slide the SIM card holder to unlock the SIM card slot. Flip the SIM card holder in an upward direction. Pull the SIM card out of the SIM card holder and remove it from the computer. NOTE: Close the SIM card holder after the SIM card has been removed from the computer.

  • Page 24: Installing The Sim Card

    Installing The SIM Card Push the SIM card into the SIM card slot until it clicks into place. Install the label door. Follow the procedures in After Working Inside Your Computer.

  • Page 25: Removing The Bottom Cover

    Removing The Bottom Cover Follow the procedures in Before Working On Your Computer. Remove the label door. NOTE: Remove the stylus pen and the dummy SD card to prevent any damage to the computer. Remove the screws that secure the bottom cover to the computer. Press on the latch to release the top section of the bottom cover.

  • Page 26: Installing The Bottom Cover

    Installing The Bottom Cover Attach the bottom cover to the computer. Push the edges of the bottom cover into the securing clips until they are fully engaged. Tighten the screws that secure the bottom cover. Install the label door. Follow the procedures in After Working Inside Your Computer.

  • Page 27: Removing The Battery

    Removing The Battery Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Disconnect the battery cable. Remove the screws that secure the battery to the computer. Lift up the battery and remove it from the computer.

  • Page 28: Installing The Battery

    Installing The Battery Place the battery in the battery compartment. Tighten the screws that secure the battery. Connect the battery cable. Install the bottom cover. Install the label door. Follow the procedures in After Working Inside Your Computer.

  • Page 29: Removing The Wireless Local Area Network (Wlan) Card

    Removing The Wireless Local Area Network (WLAN) Card Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Remove the battery. Disconnect the antenna connected to the WLAN card. Remove the screw that secures the WLAN card. Remove the WLAN card from the computer.

  • Page 30: Installing The Wireless Local Area Network (Wlan) Card

    Computer. Optionally if the Latitude ST unit is shipped from the factory without a LAN driver and the driver is installed manually, you will be prompted to turn on the WLAN. The following steps need to be performed to successfully install the WLAN card.

  • Page 31: Removing The Wireless Wide Area Network (Wwan) Card

    Removing The Wireless Wide Area Network (WWAN) Card Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Remove the battery. Disconnect the antenna connected to the WWAN card. Remove the screw that secures the WWAN card. Remove the WWAN card from the computer.

  • Page 32: Installing The Wireless Wide Area Network (Wwan) Card

    Installing The Wireless Wide Area Network (WWAN) Card Slide the Wireless Wide Area Network (WWAN) card into its slot. Tighten the screw securing the WWAN card in place. Connect the antennas according to the color code on the WWAN card. Install the battery.

  • Page 33: Removing The Internal Storage Device (Solid State Drive)

    Removing The Internal Storage Device (Solid State Drive) Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Disconnect the battery cable. Remove the screw that secures the solid state drive to the computer. Lift the solid state drive diagonally and remove it from the computer.

  • Page 35: Removing The Coin-Cell Battery

    Removing The Coin-Cell Battery Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Remove the battery. Remove the Internal Storage Drive. Disconnect the coin-cell battery cable. Release the coin-cell battery cable and remove the coin-cell battery from the computer. Installing The Coin-Cell Battery Place the coin-cell battery in its compartment and route the coin-cell battery cable.

  • Page 37: Removing The Speaker

    Removing The Speaker Follow the procedures in Before Working On Your Computer. Remove the label door. Remove the bottom cover. Remove the battery. Remove the screws that secure the speaker to the computer. Disconnect the speaker cable. Lift up the speaker and remove it from the computer.

  • Page 38: Installing The Speaker

    Installing The Speaker Connect the speaker cable to the system board. Tighten the screws that secure the speaker. Install the battery. Install the bottom cover. Install the label door. Follow the procedures in After Working Inside Your Computer.

  • Page 39: Removing The Middle Frame Assembly

    Removing The Middle Frame Assembly Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the label door. Remove the bottom cover. Remove the battery. Remove the screws that secure the middle frame assembly to the computer. Peel away the tapes that secure the antenna to the display assembly.

  • Page 40: Installing The Middle Frame Assembly

    Installing The Middle Frame Assembly Attach the middle frame assembly to the computer. Push the edges of the middle frame assembly into the securing clips until they are fully engaged. Connect the display cable. Affix the tapes that secure the antenna to the display assembly. Tighten the screws that secure the middle frame assembly to the computer.

  • Page 41: Removing The Camera

    Removing The Camera Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the label door. Remove the bottom cover. Remove the battery. Remove the middle frame assembly. Disconnect the camera cable from the system board. Peel the camera cable from the adhesive affixing it to the system board.

  • Page 42: Installing The Camera

    10. Remove the screw that secures the camera board to the computer. 11. Lift up the camera board and remove it from the computer. 12. Disconnect the camera cable from the camera board. Installing The Camera Connect the camera cable to the camera board. Place the camera on the top edge of the display assembly.

  • Page 43: Removing The Input/Output (I/O) Board

    Removing The Input/Output (I/O) Board Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the label door. Remove the bottom cover. Remove the battery. Remove the middle frame assembly. Disconnect the I/O board cable from the system board. Remove the screw that secures the I/O board to the computer.

  • Page 44: Installing The Input/Output (I/O) Board

    Installing The Input/Output (I/O) Board Place the I/O Board on the top edge of the display assembly. Tighten the screw that secures the I/O board to the computer. Connect the I/O board cable to the system board. Install the middle frame assembly.

  • Page 45: Removing The Docking Board

    Removing The Docking Board Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the label door. Remove the bottom cover. Remove the battery. Remove the middle frame assembly. Disconnect the docking board cable from the system board. Turn the middle-frame assembly over, lift up and remove the docking board from the computer.

  • Page 46: Installing The Docking Board

    10. Lift up the securing clips and disconnect the docking board cable from the docking board. Installing The Docking Board Connect the docking board cable to the docking board and flip down the securing clips. Ensure that the docking cable is connected facing upwards, the label "DB" and the arrow is pointing outwards from the system board connector.

  • Page 47: Removing The System Board

    Removing The System Board Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the SD memory card. Remove the label door. Remove the phone SIM. Remove the bottom cover. Remove the battery. Remove the WLAN card.

  • Page 48: Installing The System Board

    15. Lift up the system board and remove it from the computer. Installing The System Board Tighten the screw that secures the system board to the middle frame assembly. Turn the middle-frame assembly over, and connect the camera cable to the system board, docking board cable, speaker cable, and the coin-cell battery cable.

  • Page 49: Removing Low-Voltage Differential Signaling (Lvds) Cable

    Removing Low-Voltage Differential Signaling (LVDS) Cable Follow the procedures in Before Working On Your Computer. Remove the digitizer pen. Remove the label door. Remove the bottom cover. Remove the battery. Remove the middle frame assembly. Peel open the tape securing the display cable. Disconnect the display cable.

  • Page 50: Installing The Low-Voltage Differential Signaling (Lvds) Cable

    Installing The Low-Voltage Differential Signaling (LVDS) Cable Connect the display cable to the display panel assembly. Affix the tape that secures the display cable. Install the middle frame assembly. Install the battery. Install the bottom cover. Install the label door. Install the digitizer pen.

  • Page 51: System Setup

    Turn on (or restart) your computer. When the blue DELL logo is displayed, you must watch for the F2 prompt to appear. Once the F2 prompt appears, press <F2> immediately.

  • Page 52: Boot Menu

    Boot Menu Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system. Hard Drive Network Diagnostics and Enter Setup options are included in this menu. The devices listed on the boot menu depend on the bootable devices in the system.
  • Page 53 Specifies if the computer battery will Default: Disabled be charged when connected to an AC power source. Express Charge A Dell fast charging technology. Default: Enabled Battery Health Displays the current battery health. Miscellaneous Devices These fields let you enable or disable various on-board devices.
  • Page 54 Table 6. Security Tab Option Function Unlock Setup Status Specifies whether the system setup is locked by an administrator. Admin Password Status Specifies whether an admin password has been assigned. System Password Status Specifies whether a system password has been assigned. HDD Password Status Specifies whether a HDD password has been assigned.

  • Page 55: Troubleshooting

    Troubleshooting Enhanced Pre-boot System Assessment (ePSA) The ePSA is a diagnostic utility available on your computer. This utility includes a series of tests for a computer's hardware. You can run these tests even if the computer lacks any media (hard drive, CD drive, etc.). If a ePSA-tested component fails, the system displays an error code and generates a beep code.
  • Page 56 The computer will start up and begin running the ePSA utility automatically. During the testing process, you will be prompted to answer a YES or NO question. To respond, press Volume Up = YES or Volume Down = NO. Press the Security Button (Ctrl-Alt-Del) to click OK once the tests are completed. The volume up and down buttons can also be used as the Tab key when switching between options.

  • Page 57: Beep Codes

    Beep Codes The computer may emit a series of beeps during start-up if the display cannot show errors or problems. These series of beeps, called beep codes, identify various problems. The delay between each beep is 300 ms, the delay between each set of beeps is 3 seconds, and the beep sound lasts 300 ms.

  • Page 58: N-Trig Digitizer Troubleshooting

    Code Cause and Troubleshooting Steps System board: BIOS ROM failure System board failure, covers BIOS corruption or ROM error Memory No memory/RAM detected Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Error) , Time-Of-Day Clock test failure , Gate A20 failure , Super I/O chip failure , Keyboard controller test failure System board failure RAM Read/Write failure...

  • Page 59: Performance Issuestroubleshooting Steps

    2. Check the system information to see how many touch points are detected. – Click Start. – Right click Computer and select Properties from the menu. – Number of touch points will appear in the information window Performance issues No multi touch functionality: N-trig Software Bundle Is Installed Troubleshooting Steps: •...

  • Page 61: Technical Specifications

    Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer. System Information Chipset Intel SM35 Express Chipset...
  • Page 62 Video Video controller Intel HD Graphics 600 Video memory 766 MB Communications Network adapter one RJ-45 connector support via docking station Wireless • Wireless On/Off functionality • WWAN and Global Navigation Satellite Systems (GNSS) • Wi-Fi Ports and Connectors Audio one microphone connector/stereo headphone/speakers connector Video...
  • Page 63 Battery Length 165.50 mm (6.56 inches) Height 5.90 mm (0.23 inch) Width 114.10 mm (4.49 inches) Weight 200.00 g (0.44 lb) Voltage 7.4 VDC Temperature range Operating 0 °C to 60 °C (32° F to 140° F) Non-Operating –20 °C to 60 °C (–4 °F to 140 °F) Coin-cell battery 3 V CR2032 lithium ion AC Adapter...
  • Page 64 Environmental Storage 5 % to 95 % (noncondensing) Altitude (maximum): Operating –15.20 m to 3048 m (–50 ft to 10,000 ft) Non-operating –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-71.04–1985...

  • Page 65: Getting Help

    Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: Visit support.dell.com.

Table of Contents