Download Print this page

RCA CRF910 User Manual

Rf modulator with s-video input

Advertisement

Quick Links

USER'S MANUAL
RF MODULATOR WITH S-VIDEO INPUT
NOTE TO CATV SYSTEM INSTALLER:
INTRODUCTION
Your Video RF Modulator is designed to convert the separate audio and
video signals (from a video camera, computer, portable VCR, or satellite
receiver, for example) into VHF TV signals that you can view on a TV set.
The FCC Wants You to Know
This device complies with Part 15 of FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Your modulator might cause TV or radio interference even when is
operating properly. To determine whether your modulator is causing the
interference, turn it off. If the interference goes away, your modulator is
causing it.
Try to eliminate the interference by:
• moving your RF Modulator away from the receiver
• connecting your RF Modulator to an outlet that is on a different
electrical circuit from the receiver
• contacting your local store for help
If you cannot eliminate the interference, the FCC requires that you stop
using your RF Modulator.
INSTALLATION
1. Seat the RF Modulator vertically :
Plug in the seat plate (included) on
the bottom of the RF Modulator until
The locking tab of the seat plate
clicks in to secure the plate to the
RF Modulator.
2. Seat the RF Modulator horizontally :
2.1 While pulling up the
locking tab, remove
the seat plate by
pushing out the seat
plate.
2.2 Attach the four self-adhesive rubber pads (included) to the
side face of the RF Modulator.
2.3 Lay down the RF Modulator on the side with the rubber
pads.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's FCC authorization to
operate this equipment.
REQUIRED PARTS
The following items (not supplied) are required to connect your RF
Modulator to a video input source and your TV.
• one audio/video shielded cable with three phono connectors at each
end, if the video source's audio output is stereo; or one audio/video
shielded cable with two phono connectors at each end if the video
source's audio output is monaural
• two 75-ohm coaxial cables with F-type connectors
• a 75-ohm-to-300-ohm matching transformer, if your TV does not have
a VHF 75-ohm F-connector
Note: The audio signal will be modulated to mono, whether the video
source is stereo or monaural.
Note to the CATV System Installer: This reminder is provided to call
the CATV system installer's attention to article 820-22 of the NEC that
provides guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CONNECTIONS
Follow these steps to connect your RF Modulator.
1. If your video source is stereo,
plug the connectors on one
end of a stereo A/V cable into
the video and audio input jacks
on the RF Modulator. Plug the
connectors on the cable's other
end into to video and audio
output jacks on the video source,
using the color coding on the
connectors as a guide.
If your video source is monaural,
plug the connectors on one end
of an A/V cable into the video
and audio input jacks on the RF
Modulator (using either the AUDIO
R or L jack). Plug the cable's other
ends into the video and audio
jacks on the video source. Connect
the 75-ohm coaxial cables to the
RF Modulator following these
guidelines:
• If your video source is equipment
with VHS VIDEO (S-video) output,
you can use a S-video cable to
connect the S-video output of video
source to the S-video input of this
RF modulator.
MODEL : CRF910
Video Source
A/V Cable
RF Modulator
Video Source
A/V Cable
RF Modulator
Video
Source
RF Modulator

Advertisement

loading

Summary of Contents for RCA CRF910

  • Page 1 USER’S MANUAL RF MODULATOR WITH S-VIDEO INPUT MODEL : CRF910 NOTE TO CATV SYSTEM INSTALLER: INTRODUCTION Changes or modifications not expressly approved by the party Your Video RF Modulator is designed to convert the separate audio and responsible for compliance could void the user’s FCC authorization to video signals (from a video camera, computer, portable VCR, or satellite operate this equipment.
  • Page 2: Specifications

    Modifying or tampering with the modulator’s internal components can cause a malfunction and invalidate its warranty and void Trademark(s) ®Registered Made in China your FCC authorization to operate it. If your modulator is not www.rca.com performing as it should, take it to your local store for assistance.