Page 3
English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 Batteries Names and Contents of Toxic or Hazardous Substances or Elements Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Please dispose of used batteries properly, following Part Name (Pb) (Hg)
Page 5
If any part appears damaged, do not attempt to use Physical setup phase: Placing the system it. Notify Bose or your authorized Bose dealer components and connecting them together. immediately. For Bose contact information, refer to the address sheet included in Kit 4.
Page 6
TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English YSTEM ETUP 1. Place the control console on a flat, stable surface near your TV. Control console kit What you need for the following steps: From Kit 1 Power supply Control console...
Page 7
English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 YSTEM ETUP 2. Plug one end of the HDMI ® cable into an HDMI 3. Plug the other end of the HDMI cable you are using INPUT connector on your TV.
Page 8
TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English YSTEM ETUP 4. Plug one end of the audio input cable into the 5. Plug the power supply output cord into the control Acoustimass ® Module connector on the control console Power connector.
Page 9
English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 YSTEM ETUP 1. Place the Acoustimass module on the floor at the same end of the room as the TV. Make sure there is a live AC outlet nearby. ®...
Page 10
TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English YSTEM ETUP 4. Remove a power cord CAUTION: DO NOT from the power cord kit. ® stand the Acoustimass module on its front or 5. Plug one end of the power cord into the AC Power back end.
Page 11
Note: You can place system speakers on wall brackets or the front edge of the shelf. floor stands. To purchase these accessories, contact your • Keep each speaker facing straight out into the local Bose dealer or visit www.Bose.com. room. Do not place them at an angle.
Page 12
TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English YSTEM ETUP 2. At the end of the speaker cable with two plugs, 4. Insert the plug marked R into the speaker to the separate the cable so each plug can reach one right of your television as you face it.
Page 13
English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 YSTEM ETUP 5. Plug the free end of the speaker cable into • When the position is determined, you can use the the SPEAKERS connector on the Acoustimass ®...
Page 14
TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English YSTEM ETUP IMPORTANT! • Before you start, make sure your speakers and Acoustimass module are in their final positions. • Do not connect any devices to the control Interactive kit console at this time.
Page 15
• Optimize the audio from your system using the ® ADAPTiQ audio calibration system. Dock compatible Operating guide USB flash drive • Connect audio/video devices to the with iPod/iPhone (for system updating only) control console. • Configure your Bose ® remote to control your connected devices.
Bottom panel Acoustimass troubleshooting table in your system operating guide. module Contacting customer service For additional help in solving problems, contact Bose ® Customer Service. See the address sheet included in Vibration can cause speakers to move, particularly if Kit 4.