XDM7510 Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
XDM7510 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDM7510 uses one 10 amp ATM fuse located beside the wiring connector.
With the unit on, press and hold DISP until the clock begins Set the Clock to flash, then release. Press TUNE hours and TUNE momentarily to save the selected time. XDM7510 OPERATION General Operation to adjust the to adjust the minutes. Press DISP...
Page 6
XDM7510 General Operation 12/24-hour Clock Programmable Display Priority Programmable Clock Priority Reset Confirmation Beep Mute OPERATION The clock will display 12-hour AM/PM time in USA frequency spacing mode (PM 10 : 00). In European frequency spacing mode, the clock will display 24-hour time (22:00).
Page 7
XDM7510 OPERATION General Operation Audio Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. VOLUME BASS TREBLE BALANCE FADER Bass Press AUD until BAS appears then rotate encoder left/right to adjust ( -6 minimum / +6 maximum).
XDM7510 Tuner Operation Seek Tuning Manual Tuning Scan Tuning Local/Distance Band Frequency Spacing Storing and Recalling Station Presets Automatically Store Stations Preset Scan OPERATION Press TUNE or TUNE next strong station. Press TUNE or TUNE then release. "MANUAL" will momentarily appear in the display.
Intro Repeat Random CD-R/CD-RW Compatibility XDM7510 CD Player Operation With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Press EJECT to eject the CD. The unit will change to previous mode of operation (AM, FM, or auxiliary input).
Page 10
XDM7510 CD Player Operation - MP3/WMA Files Playing an MP3/WMA Disc MP3 Icon WMA Icon Folder Icon Displaying Information Character Support OPERATION When an MP3/WMA encoded disc is first inserted, “READING” will appear in the display. Depending on the number of files and folders, this may take several seconds.
Page 11
MUTE Direct Select, Search and Navigate Modes Direct File Select Step 1 Step 2 XDM7510 Direct Select, Search and Navigate Modes Enter/Confirm Character Shift Character Select (A, B, C ~ 8, 9, 0) Character Backspace Press SEARCH for more than 3 seconds, to select between the following modes: •...
Page 12
XDM7510 CD Player Operation - MP3/WMA Files Alphanumeric File or Folder Search Step 1 Step 2 Step 3 Step 4 Step 5 File/Folder Navigate Step 1 Step 2 Step 3 Step 4 *Folder Access (Up one level) OPERATION Press SEARCH for more than 3 seconds, then release.
Page 13
Press INT again to cancel. Note: File repeat (current folder only), folder random and folder intro is only available on MP3/WMA discs recorded with more than one folder. XDM7510 OPERATION to select the previous folder. to select the next folder. icon will appear in...
Page 14
XDM7510 CD Player Operation - MP3/WMA Files Media Compatibility Playback Order Compatible Recording Formats OPERATION The following types of discs/files are compatible: • CD-ROM (ISO), CD-R, CD-RW • CD-DA • MP3 data • WMA data The following types of discs/files are not compatible: •...
Page 15
Sampling Frequency Rates Transfer Bit rates MP3 Tag Display Recommended Settings XDM7510 An internal buffer provides ESP (Electronic Skip Protection) to virtually eliminate skipping. When playing a disc recorded with regular audio files (CD-DA or .WAV) and MP3/WMA files, the unit will play the MP3/WMA files only.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.
CEA-2006 Power Standard Specifications (reference: 14.4VDC +/- 0.2V, 20Hz~20kHz) Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms) XDM7510 OPERATION Specifications 10Hz-20kHz >65dB 1 Bit 87.5MHz-107.9MHz...
XDM7510 Troubleshooting Problem Unit will not turn on Yellow wire not connected or incorrect voltage (no power) Red wire not connected or incorrect voltage Black wire not connected Fuse blown Unit has power Speaker wires not connected (but no sound)