Advertisement
Quick Links
Read this instructions carefully before use
Minoura Japan Headquarters
(for all customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp
www.minoura.jp
Indoor Bicycle Trainer for mini-velo
– instructions manual –
Minoura North American Tech Center
1996 East Avenue, Hayward, CA 94541 U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
Made in Japan
M20-D
Tire Capacity Size:
17 x 1-1/8" - 20 x 1-3/8"
(for U.S. residents only)
(ver.1.2 2010/2)
Advertisement
Related Manuals for MINOURA Minimag M20-D
Summary of Contents for MINOURA Minimag M20-D
- Page 1 M20-D Indoor Bicycle Trainer for mini-velo – instructions manual – Tire Capacity Size: 17 x 1-1/8" - 20 x 1-3/8" Read this instructions carefully before use Minoura Japan Headquarters Minoura North American Tech Center (for all customers) (for U.S. residents only) 1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A. Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899 Email: minoura@minoura.jp Email: support@minourausa.com www.minoura.jp Made in Japan (ver.1.2 2010/2)
-
Page 2: Important Notice
Tire and roller contact will eventually wear both your tire and the trainer roller. • M20-D is a tire drive model, so if you use M20-D with a knobby tire on BMX, a loud noise must occur. To avoid this problem, replace the rear tire to a slick pattern one. - Page 3 M20-D Schematics UF-9 UF-6 UF-7 UF-8 BF-8 BF-4 BF-6 BF-4 M5-2 EM-1 BF-6 MF-3 EM-4 EM-3 EM-13 EM-2 EM-11 LM-10 EM-5 EM-19 EM-17 EM-20 BF-4: Leg Rubber Cover (Red) EM-1: Outer Cap BF-6: Leg Rubber EM-2: Axle Holder BF-8: M20 Main Frame (White) EM-3: Drive Roller & Bearing UF-6: Right Side Coupling & Clamp Lever EM-4: Main Housing...
- Page 4 Replace your rear wheel quick release skewer to the supplied one. Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub...
- Page 5 Too tight setting will cause damage to both (Fig. H) (Fig. I) M20-D and your bike frame. Too loose setting may cause the bike to come out of the trainer during use. - Page 5 -...
- Page 6 Please note too much and too less roller pressure will bring premature tire wear. Keep correct roller pressure and maintain the air pressure in correct level before using M20-D. TIPS If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.
- Page 7 It just works to adjust the coupling distance. To remove the bike from M20-D, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller.