Panasonic WV-CF102E Service Manual

Colour cctv camera
Hide thumbs Also See for WV-CF102E:

Advertisement

Quick Links

SPECIFICATIONS

The Product with PbF
Power source and power
consumption:
Image sensor:
Effective pixels:
Scanning area:
Scanning system:
Scanning lines:
Scanning frequency:
Synchronization:
Resolution:
Video output:
White balance:
Signal-to-noise ratio:
Minimum illumination:
Switch function:
L
e
n
: s
Focal length:
F number:
Angle of view:
12 V DC, 180 mA
1/4 inch interline transfer CCD
752 (H) x 582 (V)
3.7 (H) x 2.7 (V) mm
2 : 1 interlace
625 lines
Horizontal: 15.625 kHz
Vertical: 50.00 Hz
Internal, multiplexed vertical drive (VD2)
Horizontal: 540 TV lines (at center)
Vertical: 400 TV lines (at center)
1.0 V[p-p] PAL composite 75 Ω
ATW
50 dB (equivalent to AGC Off, weight On)
1.2 lx at F2.0
Backlight compensation selector (ON/OFF), Adaptive Black
Stretch selector (ON/OFF), Simple day/night mode selector
(ON/OFF)
Fixed focal length lens
f=2.5 mm
F2.0
Horizontal: 90°
Vertical: 65°
Colour CCTV Camera
Model No.
Panasonic Corporation
©
2 0 0 9
A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d
d i s t r i b u t i o n i s a v i o l a t i o n o f l a w .
ORDER NO. AVS0901083C8
WV-CF102

Advertisement

Table of Contents
loading

Summary of Contents for Panasonic WV-CF102E

  • Page 1: Specifications

    Angle of view: Horizontal: 90° Vertical: 65° Panasonic Corporation © 2 0 0 9 A l l r i g h t s r e s e r v e d . U n a u t h o r i z e d c o p y i n g a n d...
  • Page 2 Y WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.
  • Page 3: Standard Accessories

    THIS PUBLICATION AND/OR THE CORRE- NON-INFRINGEMENT THIRD SPONDING PRODUCT (S). PARTY'S RIGHT. DISCLAIMER OF WARRANTY IN NO EVENT SHALL Panasonic Corporation (5) ANY PROBLEM, CONSEQUENTIAL BE LIABLE TO ANY PARTY OR ANY PER- INCONVENIENCE, OR LOSS OR DAM- SON, EXCEPT FOR REPLACEMENT OR...
  • Page 4: Table Of Contents

    CONTENTS MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ................1-1 ADJUSTMENT PROCEDURE ..........................2-1 WIRING DIAGRAM ..............................3-1 OVERALL BLOCK DIAGRAM ..........................3-2 SCHEMATIC DIAGRAM SENSOR BOARD ..............................4-1 MAIN BOARD (1/2) .............................. 4-2 MAIN BOARD (2/2) .............................. 4-3 I/F BOARD ................................4-4 POWER BOARD ..............................
  • Page 5: Major Operating Controls And Their Functions

    MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q Video output connector • Simple day/night mode selector [D/N] Composite video signals are transmitted. ON: The camera selects black-and-white If this unit is connected to the multiplex mode if the picture is dark, or color unit, the multiplexed VD2 that is priori- mode if the picture is bright enough.
  • Page 6 • Backlight compensation selector [BLC] ON: Compensates the background auto- matically if it is brighter than the object. OFF: This mode is used when the front of the object is extremely bright. Default setting: OFF Note: Under some conditions, such as extremely strong backlight,...
  • Page 7: Adjustment Procedure

    8 Extension Cable as shown in Fig. 1-3. ADJUSTMENT PROCEDURE (Part Number: B50040BEGDD2) 1. Test Equipment Required The following Test Equipments are required for Adjustment of the Colour CCTV Camera WV-CF102. 8 Oscilloscope 8 Frequency Counter 8 Vectorscope 8 Underscanned Colour Video Monitor Fig.
  • Page 8 8 Referring to Fig. 2-4, remove one screw (Special Screw) 2. Disassembling Procedure for that secure the Camera Unit. Adjustment Camera Unit 8 Referring to Fig. 2-1, turn the Top Cover in the Direction of the arrow. Top Cover Remove one screw. Fig.
  • Page 9 8 Referring to Fig. 2-7, remove two screws that secure the 8 Confirm that removed the Sensor Board and the Main CCD Bottom Case and remove the CCD Bottom Case Board from the Camera Unit as shown in Fig. 2-10. from the Camera Unit.
  • Page 10 3.2. Setting Up for EVR Adjustment 3. Connection and Setting Up for Adjustment (1) Preparation 8 Personal Computer (Windows XP with 25-pin Parallel 3.1. Connection Port) 8 EVR Adjustment Kit (Refer to Fig. 1-1) 8 The Fig. 3-1 shows the connecting diagram for the 8 EVR Interface Board (Refer to Fig.
  • Page 11 6. Click the icon button of "iotest Setup" program screen. 4. Adjustment Procedure (Software is saved into C:¥Program Files¥ by file name "iotest") 8 The Location of Test Points and Adjusting Controls refer to Wiring Diagram on page 3-1. 4.1. Adjustment Procedure-1 (1) Power Supply Voltage Confirmation 8 Confirm that +9.0V line voltage is obtained 9.0 V ±...
  • Page 12 3. Click Tool(T) and select "EEPROM CHECK". Note: If "SLAVE-ADDRESS Receiver Error" appears, click Option (O) and change "WAIT" valume within the limit of from 20 up to 250. Then excute item-5 and 6 again. 4. "EEPROM CHECK" menu will be displayed. Click CHECK button.
  • Page 13 7. Click OPEN+LOAD(L) button and load EV2 data. EV2 data: CF102_PAL_DATA_ver100.ev2 8. The EV2 data will be stored in EEPROM (address 0000-07FF). (Data are just example) Note: If "SLAVE-ADDRESS Receiver Error" appears, click 2. Select each item from the menu, press ENTER key of the Option (O) and change "WAIT"...
  • Page 14 (2) fsc Adjustment (4) Pedestal Level Adjustment Test Point: Video Output Connector Test Point: TD70 or TD71 (14MHz) Main Board 8 Confirm that the item "2. fsc Adjustment" is displayed. 8 Confirm that the item "4. Pedestal Level Adjustment" dis- 8 Connect the Frequncy Counter to TD70 or TD71.
  • Page 15 (8.2.a) Burst Phase R-Y Adjustment (8.2.b) Burst Level Adjustment Test Point: Video Output Connector Test Point: Video Output Connector 8 C o n f i r m t h a t t h e i t e m " 8 . 2 . a . B u r s t P h a s e R - Y 8 Confirm that the item "8.2.b.
  • Page 16 (10.2.a) 3200K R-Y Gain Adjustment Test Point: Video Output Connector 8 Confirm that the item "10.2.a. 3200K R-Y Gain Adjustment" displayed. dø 8 Keep the Colour Temperature at 3 200 K. 100% 10° 8 Aim the Camera at the Colour Chip Chart. 0°...
  • Page 17 (10.3.c) 5100K R-Y Matrix Adjustment (11) High Light Chroma Clip Adjustment Test Point: Video Output Connector Test Point: Video Output Connector 8 Confirm taht the item "10.3.c. 5100K R-Y Matrix Adjust: RAM (1028) Adjustment" displayed. 8 Confirm that the item "11. Hight Light Chroma Clip 8 Keep the Colour Temperature at 5 100 K.
  • Page 18: Wiring Diagram

    WIRING DIAGRAM VIDEO OUTPUT CONNECTOR VIDEO OUTPUT CABLE POWER CABLE POWER I/F BOARD BOARD ADJUSTMENT THROUGH INTERFACE BOARD (SW5) (Connect by using the Extension Cable and the Extension Board Ass’y for Servicing) TD71 (TD70) (14MHz) (TD70 is placed in the back) (IC2) SENSOR BOARD MAIN BOARD...
  • Page 19 SCHEMATIC DIAGRAM OF SENSOR BOARD SENSOR BOARD <INDEX> SENSOR BOARD 3.3V MOT3.3V MOT5V 3.3V TD42 TD14 TD49 TD47 TD45 TD22 TD25 TD29 TD33 TD43 OPEN MOT3.3V TD20 TD52 TD51 TD44 TD46 TD30 TD28 TD26 TD24 TD37 TD41 B1,C1 OPEN OPEN OPEN D1,E1 2.5V...
  • Page 20 SCHEMATIC DIAGRAM OF MAIN BOARD (1/2) MAIN BOARD (1/2) YSIG <INDEX> SCP-DSP YSIG CSIG CSIG ALC_VREF MAIN BOARD (1/2) ALC_VREF I2CSCL PCLK PCLK TD70,71 I2CSCL I2CSDA TD70 TD71 I2CSDA B3,B4, (14MHz) ALC_DC ALC_DC C3,C4, LLDET2 LLDET2 D3,D4 2.5V D2.5V A4,A5 LPF (VD2) LPF_2.5V 2.5V...
  • Page 21 SCHEMATIC DIAGRAM OF MAIN BOARD (2/2) MAIN BOARD (2/2) <INDEX> MAIN BOARD (2/2) NRST MMOD OPEN OPEN OPEN OPEN OPEN 3.3V SBT0B SBO0B IC10 OPEN OPEN OPEN OPEN OPEN IC11 OPEN OPEN OPEN OPEN TD44 TD48 TD52 TD56 TD60 TD64 TD67 MIC3.3V TD42...
  • Page 22: Power Board

    SCHEMATIC DIAGRAM OF I/F BOARD I/F BOARD AUDIO_9V <INDEX> SHARP BOOSTER I/F BOARD OPEN R237 L203 IC201 D6,D7, LLDET/AF_LOCK E6,E7 LLDET/AF_LOCK VIDEO OUT R238 Attachment1 OPEN Attachment2 OPEN C225 Q200 Q201 OPEN POWER MON_OUT Q202 D3,D4 BOARD OPEN OPEN OPEN Q203 Q251 Q252...
  • Page 23 SCHEMATIC DIAGRAM OF POWER BOARD POWER BOARD PVIN 0.5A 125V 1/4W +12V + +12V − 4700p POWER CABLE (E12) I/F BOARD PVIN 1/4W 4700p Important safety notice Components identified by " " mark have special characteristics for safety. When replacing any of these components, use only manufacture's specified parts. <INDEX>...
  • Page 24 CONDUCTOR VIEW OF SENSOR BOARD SENSOR BOARD <INDEX> SENSOR BOARD (COMPONENT SIDE) OPEN A1,A2, B1,B2 B1,B2 OPEN OPEN OPEN TD17 TD15 TD18 (COMPONENT SIDE) SENSOR BOARD <INDEX> SENSOR BOARD (PATTERN SIDE) OPEN B1,B2 A1,B2 OPEN OPEN OPEN OPEN OPEN (PATTERN SIDE)
  • Page 25 CONDUCTOR VIEW OF MAIN BOARD MAIN BOARD <INDEX> MAIN BOARD (COMPONENT SIDE) A1,A2, B1,B2 IC12 TD71 A1,B1 R173 R92 TD45 TD23 TD51 TD55 R165 R161 TD67 TD46 TD54 TD53 R162 R174 TD64 R166 R172 TD42 TD57 TD50 TD58 (COMPONENT SIDE) MAIN BOARD <INDEX>...
  • Page 26 CONDUCTOR VIEW OF I/F BOARD I/F BOARD <INDEX> I/F BOARD (COMPONENT SIDE) OPEN OPEN OPEN OPEN TD52 OPEN D201 R103 SW1,3,4, D202 OPEN TD38 TD14 L203 L204 D201 C220 C215 C217 D202 C244 R247 C223 VCF284RY2A PbF (COMPONENT SIDE) I/F BOARD VCF284RY2A <INDEX>...
  • Page 27 CONDUCTOR VIEW OF POWER BOARD POWER BOARD <INDEX> POWER BOARD (COMPONENT SIDE) (COMPONENT SIDE) POWER BOARD POWER BOARD <INDEX> POWER BOARD (PATTERN SIDE) A1,B1 A2,B2 (PATTERN SIDE)
  • Page 28: Exploded View (1/4) (Main Unit-1)

    EXPLODED VIEW (1/4) MAIN UNIT-1 CAMERA UNIT (Refer to page 6-3) MAIN UNIT-2 (Refer to page 6-2)
  • Page 29 EXPLODED VIEW (2/4) Numbers show screws and washers. Screw Description XTB3+8GFN Binding Head Taptite Screw XYN2+J6FN Pan Head Machine Screw and Washer Ass'y MAIN UNIT-2 Cable Tie PCB4 Serial No. Label PCB3...
  • Page 30: (3/4) (Camera Unit)

    EXPLODED VIEW (3/4) Numbers show screws and washers. Screw Description XYN2+J6FN Pan Head Machine Screw and Washer Ass'y XTB2+6GFJK Binding Head Taptite Black Screw CAMERA UNIT PCB2 PCB1...
  • Page 31 EXPLODED VIEW (4/4) PACKAGING WV-CF102 Bar Code Label...
  • Page 32: Replacement Parts List

    REPLACEMENT PARTS LIST Important Notice Components identified by " Y " mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts. RTL : Retention Time Limited (No longer available after discontinuing product). marked parts are the new parts.
  • Page 33 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION ERJ6GEY0R00V Metal 0 ohm 1/8W MAIN BOARD ERJ2GEJ101X Metal 100 ohms 1/16W R77-84 ERJ3GEY0R00 Metal 0 ohm 1/10W PCB2 (RTL) VCF10EKC1AYS Printed Circuit Board Ass'y R96,97 ERJ3GEY0R00 Metal 0 ohm 1/10W C1AB00002794 Digital Signal Processor Z1,2...
  • Page 34 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION R170 ERJ2GEJ104X Metal 100K ohms 1/16W I/F BOARD R173 D0HA131ZA001 Metal 130 ohms 1/16W R176 ERJ2GE0R00X Metal 0 ohm 1/16W PCB3 (RTL) VCF10EKY2AYS Printed Circuit Board Ass'y C1-3 F1G1C104A077 Ceramic 0.1 µF C0DBAYY00222 DC/DC Controller...
  • Page 35 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION R227 ERJ2GEJ392X Metal 3.9K ohms 1/16W POWER BOARD R228 ERJ2GEJ332X Metal 3.3K ohms 1/16W R229 ERJ2GEJ392X Metal 3.9K ohms 1/16W PCB4 (RTL) VCF10EKY3AYS Printed Circuit Board Ass'y R230 ERJ2GEJ332X Metal 3.3K ohms 1/16W IC1,2 C0DBAMH00013...

This manual is also suitable for:

Wv-cf102

Table of Contents