Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planar EL240.128.45 ICEBrite
Summary of Contents for Planar EL240.128.45 ICEBrite
- Page 1 EL240.128.45 ICEBrite™ EL Small Graphics Display USER’S MANUAL www.planar.com...
- Page 2 Revision Control Date Description August 2000 Document number OM320-00 June 2004 Document number 020-0345-00A September 2005 Document number 020-0345-00B May 2010 Document number 020-0345-00C...
-
Page 3: Table Of Contents
Contents EL240.128.45 Display ....................... 3 Features ........................3 Installation and Handling ....................3 Mounting EL Displays ....................4 Cable Length ......................... 4 Cleaning ........................4 Avoiding Burn-In ......................4 Specifications ........................5 Power ..........................5 Connector ........................7 Interface Information ...................... 8 Video Input Signals .................... - Page 4 Tables Table 1. DC Input Voltage Requirements..............5 Table 2. Video Input Requirements................6 Table 3. Connector Pinouts - J1 ..................7 Table 4. Pin Settings ..................... 8 Table 5. 8080 Video Input Timing Description ............... 9 Table 6. 6800 Video Input Timing Description ............. 10 Table 7.
-
Page 5: El240.128.45 Display
DC/DC converter. The EL240.128.45 is easily interfaced using a built-in RAiO RA8835A standard LCD controller. Each of the pixels has an aspect ratio of 1:1 (V:H) and is individually addressable to clearly display high information content graphics and text. -
Page 6: Mounting El Displays
Do not deflect the ECB out of its normal plane. The EL240.128.45 mounting tabs were designed for a 3 mm screw. WARNING: These products generate voltages capable of causing personal injury (high voltage up to 230 V ). -
Page 7: Specifications
Performance characteristics are guaranteed when measured at 25 °C with rated input voltage unless otherwise specified. Planar does not recommend operation of the display outside these specifications. Table 1. DC Input Voltage Requirements. -
Page 8: Figure 1. Power Curve Diagram
HIgh-level input voltage (except SEL1) V IH 0.5 x V L HIgh-level input voltage SEL1 0.8 x V L Logic input current* – ±10 (-2000) µA * Signals /WR, /CS, SEL1, /RD, SELFTEST, /RES have pullup resistors (4.7 kΩ) EL240.128.45 Operations Manual (020-0345-00C) -
Page 9: Connector
Signal Description (+12 Display voltage Ground Ground (+5 V) Logic voltage Reset Write Read Chip Select Address SELFTES Ground input/output input/output input/output input/output input/output input/output input/output input/output SEL1 Select READY Display ready Ground LUMA Luminance control EL240.128.45 Operations Manual (020-0345-00C) -
Page 10: Interface Information
VL (+5V) VH(+12V) Pins 1 and 2: +12 V supply for DC-DC converter and display analog circuits LUMA Pin 24: Luminance control input Pins 3, 4, 12, and 23: Signal return for logic and power supplies EL240.128.45 Operations Manual (020-0345-00C) -
Page 11: Video Input Signals
Address setup time WR, RD System cycle time Strobe pulsewidth CL=100 pF Data setup time D0 to D7 Data hold time RD access time ACC8 Output disable time All signals Tr, Tf Input rise and fall times EL240.128.45 Operations Manual (020-0345-00C) -
Page 12: Figure 4. 6800 Video Input Timing Diagram
CYC6 R//W Address setup time Address hold time Data setup time CL=100 pF D0 to D7 Data hold time Output disable time Access time ACC6 Enable pulsewidth All signals Tr, Tf Input rise and fall times EL240.128.45 Operations Manual (020-0345-00C) -
Page 13: Dimming
If the SELFTEST pin is pulled high during normal operation, the display will enter the self-test mode with the all-pixels-on pattern. Power-up Sequence No special power-up or video sequencing is required. EL240.128.45 Operations Manual (020-0345-00C) -
Page 14: Optical
7.1:1 @ 120 Hz frame rate; 13:1 @ 240 Hz frame rate Command Description The EL240.128.45 display is driven by the RAiO RA8835A controller. For details on using this controller, refer to the Command Description section of the RA8835 manual titled RA8835 Dot Matrix LCD Controller Specification. -
Page 15: Environmental
15 Subpart J, Class B and EN55022 Class B when housed in a suitable enclosure. The display will be a recognized component under UL1950 by Underwriters Laboratories. The display will not inhibit the end product from complying with CSA C22.2 No. 950 and EN60950. EL240.128.45 Operations Manual (020-0345-00C) -
Page 16: Mechanical Characteristics
The component envelope shown in Figure 4 illustrates the distance components extend behind the display. Tall components do not necessarily fill this area. Planar reserves the right to relocate components within the constraints of the component envelope without prior customer notification. -
Page 17: Figure 5. Display Dimensions
Tolerances unless specified: ± 0.50 ± 0.25 Figure 5. Display Dimensions. Note: This is not a controlled version of the mechanical drawing. Prior to beginning your design, please contact Planar Applications Engineering for the current detailed drawing. EL240.128.45 Operations Manual (020-0345-00C) -
Page 18: Description Of Warranty
Support and Service Planar is a U.S. company based in Beaverton, Oregon and Espoo, Finland, with a world-wide sales distribution network. Full application engineering support and service are available to make the integration of Planar displays as simple and quick as possible for our customers. - Page 19 EL240.128.45 Operations Manual (020-0345-00C)
- Page 20 Tel: +358-9-420-01 Hours: M-F, 7:00am - 3pm CET © 2010 Planar Systems, Inc. 10/05 Planar is a registered trademark of Planar Systems, Inc. ICE, ICEBrite, and ICEPlus are trademarks of Planar Systems, Inc. Other brands and names are the property of their respective owners.