Page 1
Quick Setup Confirm Your Receiver Model If your receiver looks like DISH Player-DVR 942 this... If your receiver looks like DISH Player-DVR 522 & this... DISH Player-DVR 625 If your INFO MENU SYS INFO ® SELECT receiver DISH 501 & DISH 508 looks like DISH Player-DVR 510 one of...
Install Your Selected Note: If you will be using the blue TV2 key that comes already installed in your remote, skip this step and proceed with the next step (Insert the Batteries). Separate the key from Pull the the remote by inserting remote your thumbnail or coin battery...
Making the Remote Work With Your Receiver If you installed one of these keys, continue with Make sure the UHF antenna is installed on the back of the receiver. System Info Mon, October 18 Model ID DISH Player-DVR 942 Receiver CA ID R00000000000-00 Smart Card ID S00000000000-00...
Program the Remote to Control Your TV Turn your TV on. POWER Press POWER. Press POUND. Quick Setup Press & hold the TV Mode button until all Mode buttons light up. Press the UP ARROW repeatedly until your TV turns off (about 1 press per second) Press the POWER...
Programming the Recover Button for TV2 Operation For TV2 Remote Controls on 942, 625, & 522 Receivers Programming your Recover button allows you to easily regain satellite programming if you accidentally change TV channels or inputs. Press & hold the TV Mode button until all Mode buttons light up.
Quick Setup/Operation Placing Your Remote in Limited Mode Limited Mode locks out all the TV mode operations except for TV power, Mute, and Volume. This prevents you from accidentally tuning away from satellite programming. Press & hold the TV Mode button until all Mode buttons light up.
TV channel viewed Picture-In-Picture (PIP) Buttons Display PIP features on some TVs with PIP capabilities Note: Remote operation is different on DISH Network TVs. See your DISH Network TV User's Guide for proper operation. Operation POWER TV/VIDEO PAGE VOLUME MUTE...
Remote Operation VCR Mode To use the features described in this section, make sure you are in VCR mode by pressing the VCR Mode button. You can use this mode to operate your DVD player instead of a VCR. Remote programming is required. See VCR/DVD Power &...
Table of Contents COLOR PAGES... Quick Setup Confirm Your Receiver Model and Select the Right Key .. Install Your Selected Key ... Insert the Batteries ... Making the Remote Work with Your Receiver ... Program the Remote to Control Your TV ... Programming the Recover Button for TV2 Operation ...
EMOTE ONTROL Use this full-function remote to control a variety of DISH Network receivers, such as Standard Definition, High Definition, and Digital Video Recorder receivers. Also, you can program the remote to control most of the popular brands of audio/video equipment like a TV, VCR, DVD player, or a second DISH Network satellite receiver.
IMITED You can program your remote control in Limited Mode to keep from accidentally changing the channel on your TV or VCR. When you use the remote to control your TV in Limited Mode, you will only be able to use the POWER, MUTE, and VOLUME buttons to control your TV. Also, when you use the remote to control your VCR in Limited Mode, you will only be able to use the POWER and VCR function buttons.
10 If the code doesn’t work, redo steps 3 through 9 with another equipment code from the tables. 11 If you can’t find a code that works try, Scanning for Equipment Codes that follows. CANNING FOR Instructions Turn the equipment on.
Page 15
Instructions For AUX mode only. Press 0 for a second TV, or 1 for a second VCR, or 2 for a tuner, or amplifier. Then press the STAR (*) button. Press POWER. Press the UP or DOWN ARROW repeatedly until the equipment turns off.
WITCHING ETWEEN ONTROL When you set up the remote to control a TV, the MUTE and VOLUME buttons control the TV volume, even if your remote control is in SAT mode. However, if you want to use the AUX mode to control a tuner or amplifier that has a volume setting, you can set up the remote to control the equipment’s volume instead of the TV volume while your remote control is in SAT mode.
ROGRAMMING THE ECEIVER IN If you have another DISH Network satellite receiver installed, you can use this remote in AUX mode to control it along with your new receiver. When you program the remote to control the other receiver, the remote will send out IR and UHF (not UHF Pro) signals to the receiver.
Instructions Press the POUND (#) but- ton twice. The mode button flashes the number for each digit of the equipment code, with a pause between the groups of flashes. A quick flash is for zero. For AUX mode, the first group of flashes tells you what the AUX mode controls.
Use the NUMBER PAD to enter any number between 1 and 16, but not the one you wrote in step 1. Press POUND (#). If you entered the address correctly, SAT will flash three times. Write down the number you entered in Your Remote Control Codes on page 24.
TV1 UHF P ETTING DISH P LAYER Use these special instructions only if you are going to use the green 1 UHF Pro key to control the TV1 side of your DISH Player-DVR 522 or 625. When you are finished setting up the remote control, you’ll be able to operate the TV1 side of your DISH Player-DVR 522 or 625 from long distances.
Page 21
10. Press the POUND (#) button. If you entered the address correctly, the SAT mode button will flash three times. 11. Make sure the System Information screen shows that this address matches the number you entered in step 9. 12. Select Done to close the System Information screen. If nothing happens, press RECORD, and then select Done.
Page 27
TV/DVD C OMBO Programming for combination equipment: Program the remote control in TV mode and then in VCR (or AUX - press 1 before entering the DVD code) mode. Aiwa 751 Apex 757 Broksonic 752 Konka 753 Panasonic 734 765 TV/VCR C OMBO Programming for combination equipment: Program the remote...
ROUBLESHOOTING What’s What’s Wrong Happening While doing • If you don’t press remote control any button procedure, the for 20 seconds in a remote control programming stops working. sequence, the remote shuts off its programming function. You cannot find • The keys have two the key(s) sides.
Page 29
What’s What’s Wrong Happening Your remote • The remote control control isn’t is in the wrong working mode. • You might be using the wrong remote control (TV1 or TV2). • Your batteries are worn out. • The remote control’s A/B switch is in the wrong position When you press...
Proof of Purchase to be out of warranty. This warranty extends only to the original user (“you,” “your”) of the DISH Network remote control and is limited to the purchase price of the remote control. EchoStar Technologies Corporation and its affiliated companies (“we,”...
Page 31
CCESSORY ARRANTY An accessory is any DISH Network branded equipment, displaying the DISH Network logo, excluding the receiver, Smart Card, cables and hookups, and non-mechanical components. A one-year warranty becomes effective upon the activation of the DISH system or date of purchase, if bought separately.
Page 32
EGULATORY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this device may void your authority to operate this equipment.
Reference Tables Write down your remote address, channel numbers/inputs, TV, VCR, DVD player, and stereo equipment codes as you program them for future reference. Remote Address Channel or Input for Satellite Programming Channel for Satellite Programming on TV2 Auxilary Equipment Code To read out your remote codes, see page 10 for instructions.