Dimension One Spas – @Home Series Owner’s Manual Spa Information My Spa Model Name: Serial Number: Date Purchased: Date Installed: Gallons/Liters: Notes: Dealer Information: Dealer’s Name: Address: City: State, Zip: Telephone: Fax:...
DYNAMIC L.E.D. LIGHT (ON CERTAIN MODELS) ...12 ROUTINE EQUIPMENT MAINTENANCE...13 DRAINING YOUR HOT TUB ...13 FILTER CLEANING ...13 LIGHT BULB REPLACEMENT...13 CARE FOR THE HOT TUB SURFACE...14 SPECIAL COLD WEATHER INSTRUCTIONS...15 TROUBLESHOOTING GUIDE ...18 Dimension One Spas – @Home Series Owner’s Manual Table of Contents...
To Reduce the Risk of Injury: Pregnant women, the elderly, infants, or persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes, should consult a physician before using a spa. People with infections diseases should not use a hot tub. •...
Dimension One Spas – @Home Series Owner’s Manual • Do not permit electric appliances (such as a light, telephone, radio, television, etc.) within 1.5m of this spa or hot tub. • AVERTISSEMENT: NE PAS PLACER D’APPAREIL ÉLECTRIQUE (LUMINAIRE, TÉLÉPHONE, RADIO, TÉLÉVISEUR, ETC.) À MOINS DE 1.5 M DE CETTE CUVE DE RELAXATION.
Dimension One Spas – @Home Series Owner’s Manual Warning Signs Each spa has been provided with a Warning Sign and an Important Notice label. This label outlines safety precautions. This sign should be permanently placed in a location that is visible to the spa user.
Dimension One Spas – @Home Series Owner’s Manual Initial Startup IMPORTANT: About the GFCI Circuit Breaker — The GFCI (Ground Fault Circuit Interrupter — also called a "circuit breaker") is an electrical safety switch that automatically shuts off power to the spa in case of an electrical malfunction.
Dimension One Spas – @Home Series Owner’s Manual 7. Remove the two shipping bolts located on the front of the pump mount (circled in illustration). 8. If the spa has a bleeder valve in the skimmer area (see picture at right) remove it to allow air to escape from the pump(s) while filling the spa.
Dimension One Spas – @Home Series Owner’s Manual 12. One minute after the power is turned on, the spa will automatically begin its first one-hour filtration cycle (this cycle may be interrupted if the Jet pumps are being turned on and off at the time). On two-pump models, Pump 2 will operate on high speed for the first minute of each filter cycle.
Dimension One Spas – @Home Series Owner’s Manual Operation Control the functions of your spa using the topside Control Panel. Understand the following information before starting up the spa. The Control Panel Control Function Display Window The Display Window shows the current status of the hot tub: its monitoring functions, self-diagnostics, or programming messages.
Dimension One Spas – @Home Series Owner’s Manual Control This light glows when the heater is on. 5. JETS 1 Button On American models, pushing the JETS 1 Button once starts the pump on LOW speed. Pushing it a second time turns on HIGH speed. Pushing it a third time turns the pump off.
Dimension One Spas – @Home Series Owner’s Manual Control Programming the Spa Functions To initiate the programming sequence at any time, hold PROGRAM for 3 seconds. If within 10 seconds no button is pushed, the spa will automatically exit the programming sequence and revert to the pre-set factory default settings. To exit the programming sequence at any time, do not press any button for 10 seconds.
110° F (43° C). Then reset the power to the spa by resetting the GFCI breaker. If the problem recurs, turn off the power to the hot tub and contact your local Authorized Dimension One Spas Dealer, or...
• Mode Memory: When the light has been off for more than 10 seconds, it automatically remembers its previous mode and returns to it the next time you turn the light on. Dimension One Spas – @Home Series Owner’s Manual...
Dimension One Spas – @Home Series Owner’s Manual Routine Equipment Maintenance Draining Your Hot Tub The spa is gravity-drained, without the need for a pump. To drain the spa, locate the hose bib, which was attached to the spa in the Initial Setup operation (described earlier), on the base near the lower left side of the equipment panel. Remove the cap (if any) from the hose bib.
Do not attempt to remove the lens without the special tool. If it is lost, contact Dimension One Spas Service Department to have one sent. Be sure the rubber O-ring behind the lens is undamaged and is properly positioned when replacing the lens.
Special Cold Weather Instructions All Dimension One Spas are designed for year-round use. They are insulated for energy efficiency and to protect the plumbing and equipment when the system is operational. The system has a “Smart Winter” freeze protection mode to circulate water during freezing weather, assuming the system has electrical power and the proper water level.
Dimension One Spas – @Home Series Owner’s Manual 13. Remove both bleeder valves from the top of the filter canister area. Place hose of a high-pressure air blower into the rear-most bleeder fitting first. Confirm that water mist is blowing from one or both of the circulation system return jets in the footwell of the system.
Always check the system after any power failure to ensure that it is operational. Draining and discontinuing the operation of the system disables the freeze protection feature and may result in freeze damage. For more information about winterizing your spa, please contact your local Authorized Dimension One Spas dealer.
Turn down the “set temperature” on the control panel Call your dealer for service Call your dealer for service Fill hot tub to about 6 inches (15 cm) below the top of the spa. Corrective Action Check circuit breaker and/or GFCI.