JETWAY 920BFR3A User Manual

3d-agp vga / 3d-audio m/b for pentium ii / iii

Advertisement

3D-AGP VGA / 3D-Audio M/B
The author assumes no responsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the information
contained herein.
Trademark:
*
Pentium is registered trademark and MMX is a trademark of Intel corporation, the other names and brands
are the property of their respective owners.
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
920BF/920BN
USER'S MANUAL
FOR Pentium
NO. G03-920BFR3A
Release date: DEC 2000
** Year 2000 compliant **
II / III

Advertisement

Table of Contents
loading

Summary of Contents for JETWAY 920BFR3A

  • Page 1 The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. NO. G03-920BFR3A Release date: DEC 2000 ** Year 2000 compliant ** Trademark: Pentium is registered trademark and MMX is a trademark of Intel corporation, the other names and brands are the property of their respective owners.
  • Page 2: Table Of Contents

    TABLE OF CONTENT Chapter 1 1-1 Preface ....................1 1-2 Key Feature ....................1 Chapter 2 Hardware Installation ..................3 2-1 Unpacking....................3 2-2 Motherboard Diagram ................4 2-3 Quick Reference for Jumpers, Connectors & Expansion Socket.....5 2-4 Installation Steps ..................6 2-5 Jumper Settings ..................6 2-6 System Memory (DRAM) ................8 2-7 Central Processing Unit (CPU) ...............8 2-8 Expansion Cards..................11...
  • Page 3: Preface

    Chapter 1 1-1 Preface Thank you for purchasing this multifunction motherboard. It has the most flexibility you can find in today’s computer market. This board integrates both Intel Pentium®II /Pentium®III & Celeron™(Slot 1) / Coppermine processor and Celeron™ (Socket 370) PPGA / FCPGA processor interface into a compact PC/AT compatible system along with share memory type 3D AGP VGA on-board, 3D PCI Audio on-board to support 4 channels speaker(If on-board embedded Audio chip only), Ultra DMA 66, ACPI/AMP power management, and many other...
  • Page 4 combine with DVD player to create a home theater system (This upgrade kit includes Optical Module, Optical Cable, and Software DVD Driver). • Chipset: SiS 620/5595 AGPset chip with I/O subsystems; CMI 8738 3D PCI Audio chip (Option for motherboard that embedded Audio chip). •...
  • Page 5: Hardware Installation

    Hardware Installation 2-1 Unpacking This mainboard package should contain the following: • The mainboard • USER’S MANUAL for mainboard • Cable set for Ultra DMA 33 IDE x1, Floppy x1, COM1 & COM2 x1, LPT x1, VGA x1, Audio and Game x1(For motherboard that embedded Audio chip) •...
  • Page 6: Quick Reference For Jumpers, Connectors & Expansion Socket

    CPUFAN ATKB MS PIN1 COM2 COM1 GAME LPT1 SPKIN1 AUDIO SLOT1 5595 DIMM1 DIMM1 BATT DIMM2 DIMM2 IDE2 IDE1 KEYLOCK TBSW FLO PPY PS/ON HDLED SPEK RST TBLED Figure 2-1 Optional connector for motherboard that embedded wit Audio Chip Quick Reference for Jumpers, Connectors & Expansion Socket Jumpers Jumper Name...
  • Page 7: Installation Steps

    U14-7 CPU Bus Frequency Selection Open:100MHZ(off), Closed:66MHz(on) CMOS RAM Clear 1-2 Clear CMOS, 2-3 Normal On board VGA Enabled/Disabled open : Enabled,closed : Disabled Keyboard power on function 1-2 : Enabled , 2-3 : Disabled VIO Voltage Selection 1-2 : 3.45V , 2-3 : 3.52V Connectors Connector Name...
  • Page 8: Jumper Settings

    2. Install the CPU 3. Install DRAM Modules 4. Install Expansion card 5. Connect Cables, Wires, and Power Supply 2-5 Jumper Settings CPU Bus Frequency Selection : U14-7 U14-7 66MHz : Closed 100MHz : Open ¡ ° You can also set the CPU Bus frequency and CPU ratio from the “CHIPSET FEATURES SETUP”...
  • Page 9: System Memory (Dram)

    Normal Clear CMOS CMOS RAM (Normal / Clear CMOS Data) 3. On Board Audio Chip Enabled / Disabled connector: JP6 Closed (Default) : Enabled Open : Disabled 4. On board VGA function Enabled / Disabled connector: J5 Closed : Disabled Open (Default) : Enabled 5.
  • Page 10: Central Processing Unit (Cpu)

    This main board supports 168-pins DIMM modules, the Max Memory Size is 1.0GB Because of the VGA share memory function, the system must always occupy BANK0 (DIMM1)to booting the system. DIMM 1 DIMM 2 System can be Accept or Not ×...
  • Page 11 Lock Blank White Dot Lever CPU ZIF Socket 370 ® ® 2-7-3 Intel Pentium III Processor (256K) in the FC-PGA form factor: Mechanical Features The FC-PGA package has the processor’s silicon die directly mounted to a pinned interposer substrate. The pin grid array is partially populated and there may be surface mount components in the unpopulated central area of the pin field.
  • Page 12: Cpu Insertion

    FC-PGA with a PPGA heatsink CPU Insertion Step 1 Open the socket by raising the actuation lever. Step 2 Insert the processor. Ensure proper pin 1 orientation by aligning the FC-PGA corner marking with the socket corner closest to the actuation arm tip. The pin field is keyed to prevent mis-oriented insertion.
  • Page 13: Expansion Cards

    2-8 Expansion Cards You must read the documentation come with expansion card for any hardware or software settings that may be required to setup your specific card. Installation Procedure: 1. Read the documentation from your expansion card. 2. Set any necessary jumpers on your expansion card. 3.
  • Page 14 Power connector: AT Power Connector (12-pin block): PW1 This connector connects to a standard AT power supply. To connect the leads from the power supply, ensure first that the power supply is not plugged. Most power supplies provide two plugs (P8 and P9), each containing six wires, two of which are black. Orient the connectors so that the black wires are located in the middle.
  • Page 15 PIN 1 DATA PS/2 Mouse Module Connector 5. Parallel Printer Connector (26-pin Block): LPT1 Connection for the enclosed parallel port ribbon cable with mounting bracket. Connect the ribbon cable to this connection and mount the bracket to the case on an open slot. It will then be available for a parallel printer cable.
  • Page 16 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.
  • Page 17 D. Speaker connector: SPEAKER This 4-pin connector connects to the case-mounted speaker. See the figure below. Keyboard Lock Power LE D TurboSW G ND VCC G ND VC C G ND G ND G ND VC C G ND Turbo LE D Speaker R eset SW System Case Connections...
  • Page 18 SLEEP. Pushing the switch while in the ON mode more than 4 seconds will turn the system off. The system Power LED shows the status of the system’s power. Selections PS-ON One touch Power ON/OFF PS-O N ATX Power button/Soft Power button 16.
  • Page 19 19. Game Port connector: GAME Orient the red stripe on the monitor cable with Pin 1 Audio G AME Game GAME PORT Connector 20. CD-ROM Audio connector: JP3,JP4 CD-ROM Audio connector 21. PC Speaker signal Input connector: SPKIN 1 SPKIN 1 22.
  • Page 20: Chapter 3 Award Bios Setup

    Chapter 3 AWARD BIOS SETUP Award's ROM BIOS provides a built-in Setup program which allows user modify the basic system configuration and hardware parameters. The modified data will be stored in a battery- backed CMOS RAM so data will be retained even when the power is turned off. In general, the information saved in the CMOS RAM stay unchanged unless here is configuration change in the system, such as hard drive replacement or new equipment is installed.
  • Page 21: Bios Features Setup

    ROM PCI/ISA BIOS (2A6IMJ19) STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Tue, Feb, 23 1999 Time (hh:mm:ss) : 13 : 43 : 56 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SEC TOR MODE Primary Master : Auto 0 Auto Primary Slave : Auto...
  • Page 22 Virus Warning : Disabled Video BIOS Shadow : Enabled CPU Internal Cache : Enabled C8000-CBFFF Shadow : Disabled External Cache : Enabled CC000-CFFFF Shadow : Disabled CPU L2 Cache ECC Checking : Enabled D0000-D3FFF Shadow : Disabled Processor Number Feature : Enabled D4000-D7FFF Shadow : Disabled Q u ick Power On Self Test : Enabled...
  • Page 23 Enabled: Floppy A & B will be swapped under the DOS Disabled: Floppy A & B will be not swap • Boot Up Floppy Seek: During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.
  • Page 24: Chipset Features Setup

    Enabled: Video shadow is enabled Disabled: Video shadow is disabled • C8000 - CBFFF Shadow: CC000 - CFFFF Shadow: D0000 - D3FFF Shadow: D4000 - D7FFF Shadow: D8000 - DBFFF Shadow: DC000 - DFFFF Shadow: These categories determine whether optional ROM will be copied to RAM by 16K byte or 32K byte per/unit and the size depends on chipset.
  • Page 25: Power Management Setup

    clock cycles of CAS latency depends on the DRAM timing. Do not reset this field from the default value specified by the system designer. The choice: 2T, 3T. • AGP Aperture Size : Select the size of the Accelerated Graphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space.
  • Page 26: Pnp/Pci Configuration Setup

    • Stdby Speed (div by) : Select a divisor to reduce the CPU speed during Standby mode to a fraction of the full CPU speed. The speed is reduced to a fraction of the CPU's normal speed. The divisors range from 1 to 8-0. The choice: 1~8 •...
  • Page 27 ROM PCI/ISA BIOS (2A6INJ19) PNP/PCI CONFIGURATION SETUP AWARD SOFTWARE, INC. Resources Controlled By : Manual Reset Configuration Data: Disabled IR Q - 3 assigned to : PCI/ISA PnP IR Q - 4 assigned to : PCI/ISA PnP IR Q - 5 assigned to : PCI/ISA PnP IR Q - 7 assigned to : PCI/ISA PnP IR Q - 9 assigned to : PCI/ISA PnP IR Q - 10 assigned to : PCI/ISA PnP...
  • Page 28: Load Setup Defaults

    ROM PCI/ISA BIOS (2A6INJ19) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT ECTION Load BIOS Default (Y/N)? Y PNP/PCI CONFIGURA FORMAT LOAD BIOS DEFAULTS SAVE & EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING Esc : Q U IT...
  • Page 29 Internal PCI : Both PS/2 mouse function : Enabled IDE Primary Master PIO : Auto USB Controller : Enabled IDE Primary Slave PIO : Auto USB Keyboard Support : Disabled IDE Secondary Master PIO : Auto Init Display Frist : AGP IDE Secondary Slave PIO : Auto VGA Shared Memory Si z e : 2MB Primary Master UltraDMA : Auto...
  • Page 30: Password Setting

    • Parallel Port Mode : Select an operating mode for the onboard parallel (printer) port. Select Normal, Compatible, or SPP unless you are certain your hardware and software both support one of the other available modes. The choice: SPP, EPP, ECP, ECP+EPP. •...
  • Page 31: Save & Exit Setup

    Date (mm:dd:yy) : Thu, Mar, 12 1998 Time (hh:mm:ss) : 13 : 43 : 56 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SEC TOR MODE Primary Master : Primary Slave Secondary Master : Select Secondary Slave Option (N = S kip):N OPTIONS SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE 1 (Y) 0 NORMAL...
  • Page 32 step1: Run “X:\SiS620\HEALTH\SETUP.EXE” file . step2: Selet “Next” to complete install driver. step3: The program will automatic install driver to system if users have question in system Hardware Monitor Setting, please read “HELP” Section in program. 4-2 Sound Driver & Audio Rack Installation( Option for Motherboard That Embedded Audio Chip ) : Special Features for CMI8738 audio chip PCI Plug and Play (PnP) bus interface, 32 bit PCI bus master.
  • Page 33 installation includes the following device drivers. CMI8738/C3DX PCI Audio Device CMI8738/C3DX PCI Audio Joystick Device CMI8738/C3DX PCI Audio Legacy Device DOS mode MPU-401 Emulator 8. Install Application Software : Click “start” key 9. Select “Run” 10. Key in the drive and path for Windows application installation program, for example, in Win95 “X:\CMI8738\Win9X\APP\Win95\SETUP.EXE”...
  • Page 34 This Audio Rack consists of several major components: Control Center: Controls the display of the PCI Audio Rack’s components. MIDI Player: Plays MIDI music files, and allows you to create your personal song playlists, and play the song files. Wave Player: Records and plays digital audio (wave) files. Allows you to create wave file playlists, and playback the wave files.
  • Page 35 Mixer panel while the four speakers mode is enabled. Mixer panel while the four speakers mode is disabled. Volume Control: Clicking on this button shows and allows you to use the output level controls. Recording Control: Clicking on this button shows and allows you use the input level controls. Input and Output Level Sliders and Buttons: For each input or output signal type, the control slider controls the loudness whereas the horizontal slider controls the balance between the two speakers.
  • Page 36 MP3 player while the loop function enables. The settings’ window while one of the SPDIF functions is enable. The 4 Speakers System This Audio Adapter provides 2 wave channels(front/rear), known as the 4 speakers system. When games or application programs via DirectSound® 3D or A3D® interface locate the sound sources to the listener's back, the two rear speakers will work to enhance the rear audio positional effect, so as to complement the insufficiency of using only two front speakers to emulate the audio effect.
  • Page 37 Optical Module Optical Cable Software DVD driver OPTICAL MODULE J1¡ G SPDIF-IN DIP-SWITCH OPTICAL OUT OPTICAL IN An example of optical kit with MD connection. The application program setup(please install CMI8738 application program first) When the connection is done, please go to the Start menu and select PCI Audio Applications\Audio Environment Setting...
  • Page 38 When all the procedures have been completed, there will be an infrared signal coming from the SPDIF/OUT of the optical fiber of the sound card. Please note that signal beam may cause severe damage to the eyes. For your safety, please point the output end to a piece of white paper to check if thebeam is in function.
  • Page 39: About Recording 24Bit Audio Setting

    Please note that in playback, if there is no gap longer than three seconds between each track, the MD can not recognize the tracks and will record all of them into one. It is recommended that you set the gap time to 3~5 seconds to meet all type of MD requirements. About Recording 24bit Audio Setting...
  • Page 40 24-bit audio can only be applied to SPDIF IN/OUT mode; it does not apply to other modes such as the four channels or the analog. No sound will be heard while in playback, yet it can be recorded. The un-selected area will be gray out.
  • Page 41 The un-selected area will be gray out. The un-selected area will be gray out.
  • Page 42 You can double-click this circuit icon to have the following setting box. By means of this setting box, you can also complete the above-mentioned setting procedures. SPDIF/IN for motherboard that embedded Audio chip An example of Portable CD Player(Output) to Main Board (Optical Input)Setup...
  • Page 43 When the connection is done, please go to the Start menu and select PCI Audio Applications\Audio Environment Setting Loopback(bypass)mode setup...
  • Page 44 CD ROM(Digital Output) to SPDIF/IN Setup When the connection is done, please go to the Start menu and select PCI Audio Applications\Audio Environment Setting Please follow these setting procedures.
  • Page 45 Now you can insert the CD into the CD ROM drive, then activate C-MEDIA CD player and push the ”play” button to do the recording job. Please note that you have to set the MD in the simultaneous-recording mode.

This manual is also suitable for:

920bf920bnJ-920bf

Table of Contents