Table of Contents
Advertisement
Quick Links
845DDA/845DDAL
845D PRO
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-845DDA3A
Release date: July 2002
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY 845DDA3A
Summary of Contents for JETWAY 845DDA3A
- Page 1 845DDA/845DDAL 845D PRO USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-845DDA3A Release date: July 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE ......................1 MANUAL REVISION INFORMATION ................1 COOLING SOLUTIONS ....................1 CHAPTER 1 INTRODUCTION OF 845DDA/845DDAL/845D PRO MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD................2 1-2 SPECIFICATION .....................3 1-3 PERFORMANCE LIST ...................4 1-4 LAYOUT DIAGRAM & JUMPER SETTING ............5 CHAPTER 2 HARDWARE INSTALLATION 2-1 HARDWARE INSTALLATION STEPS ..............7 2-2 CHECKING MOTHERBAORD'S JUMPER SETTING........7 2-3 INSTALL CPU ......................8... -
Page 3: User's Notice
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF MANUFACTURER. -
Page 4: Chapter 1 Introduction Of 845Dda/845Ddal/845D Pro Motherboard
Chapter 1 Introduction of 845DDA/845DDAL/845D PRO Motherboard 1-1 Feature of motherboard The 845DDA/845DDAL/845D PRO motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package/Northwood Processor with the Intel 845D Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. -
Page 5: Specification
1-2 Specification Spec Description ∗ ATX form factor 4 layers PCB size: 30.5x21.0cm Design ∗ Intel 845D Memory Controller Hub (MCH) Chipset Chipset ∗ Intel 82801BA I/O Controller Hub (ICH2) Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip- CPU Socket (mPGA478B Socket) Chip Pin Grid Array (FC-PGA2) package processor... -
Page 6: Performance List
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:... -
Page 7: Layout Diagram & Jumper Setting
1-4 Layout Diagram & Jumper Setting PRINT GAME/MIDI PORT PS/2 MOUSE PS/2 Keyboard LINE-IN COM1 COM2 LINE-OUT ATX 12V Power Conn. K/B Power ON Jumper (JP1) CPU Socket PS2 KB/Mouse Port CPU FAN USB Port /LAN Connector (for 845DDAL) ATX Power Conn. PC99 Back Panel DDR DIMM X2 ATX P6 Power Conn. -
Page 8: Expansion Sockets
Jumpers Jumper Name Description Page JP10 CMOS RAM Clear 3-pin Block Keyboard Power On Enable/Disabled 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.12 ATX12V ATX 12V Power Connector 4-pin Block P.13 ATXP6 ATX P6 Power Connector 6-pin Block P.13 PS/2 Mouse &... -
Page 9: Chapter 2 Hardware Installation
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. -
Page 10: Install Cpu
(2) Keyboard Power On function Enabled/Disabled: JP1 When setting Enabled you can using keyboard by key in password to power on system. 1-2 closed K/B Power ON Disable 2-3 closed K/B Power ON Enabled (Default) Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards. -
Page 11: About Intel Pentium 4 478-Pin Cpu
2-3-2 About Intel Pentium 4 478-pin CPU This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. -
Page 12: Expansion Card
NOTE! Make sure the installed memory are DDR266 SDRAM support 133MHz memory clock, otherwise the system may hang during startup. Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-Pin DDR266/DDR200 DDR SDRAM module looks like. Figure 2-4 NOTE! When you install DIMM module fully into the DIMM socket the eject tab... -
Page 13: Assigning Irq For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use. Standard Interrupt Assignments Priority Standard function System Timer Keyboard Controller Programmable Interrupt... -
Page 14: Agp Slot
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845 chipset can not support AGP 2X (3.3V). IMPORTANT! Before you plug-in AGP card, please make sure the following notice is fully understood and practiced. - Page 15 Pin 1 ROW2 ROW1 3.3V 3.3V -12V 3.3V Soft Power On Power OK +5V (for Soft Logic) +12V (2) ATX 12V Power Connector (4-pin block) : ATX12V This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption.
- Page 16 USB Port connector: J2 (USB) The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN (Only for 845DDAL) This connector is standard RJ45 connector for Network connector. Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector.
-
Page 17: Headers
This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. - Page 18 Line-In/Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-In, Line-out, MIC connector with cable. Pin 1 AUDIO L-IN-L L-IN-R G ND G ND MIC P G ND L-O UT-L L-O UT-R Line-In/Out, MIC Headers USB Port Headers (9-pin) : USB1 These headers are used for connecting the additional USB port plug.
- Page 19 This 4-pin connector connects to the case-mounted speaker. See the figure below. Power LED: PWR-LED The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.
- Page 20 These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.
-
Page 21: Starting Up Your Computer
1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. -
Page 22: Chapter 3 Introducing Bios
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 23: The Main Menu
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 24: Standard Cmos Features
Load Optimized Defaults Use this menu to load the BIOS default values that are settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values that are factory settings for the stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. -
Page 25: Advanced Bios Features
The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. - Page 26 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 27: Advanced Chipset Features
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. -
Page 28: Dram Timing Settings
Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. -
Page 29: Integrated Peripherals
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Integrated Peripherals > Onboard IDE Function Press Enter Item Help > Onboard Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Menu Level > Power On Function Button Only KB Power On Password Enter... -
Page 30: Onchip Device Function
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. -
Page 31: Onchip Super Io Function
USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled. USB Keyboard Legacy Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. -
Page 32: Power Management Setup
Parallel Port Mode : Standard Parallel Port : Enhanced Parallel Port : Extended Capability Port SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. - Page 33 This item allows you to select ACPI Suspend Type. The setting are: S1(POS), S3(STR) Video Off in Suspend This determines the manner in which the monitor is blanked. The choice are Yes → Video will off , and No→ Video always On. Video Off Method This determines the manner in which the monitor is blanked.
-
Page 34: Pm Timer Reload Events
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software PM Timer Reload Events Primary IDE 0 Disabled Item Help Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled Menu Level >> FDD, COM, LPT Port Disabled PCI PIRQ [A-D] # Disabled ↑↓→←... -
Page 35: Irq Resources
IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources CMOS Setup Utility –... -
Page 36: Miscellaneous Control
Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled. Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V) This will show the CPU/FAN/System voltage chart and FAN Speed. Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. -
Page 37: Load Standard/Optimized Defaults
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. -
Page 38: Chapter 4 Driver & Free Program Installation
DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. - Page 39 CONTROL PANEL/SYSTEM/DEVICE MANAGER). You have to install INF driver as shown below: 1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears 3. This chart shows motherboards supported 4. Select if you want computer re-started by the driver click Yes click Finish NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\INF\SETUP.EXE...
-
Page 40: Sound Install Alc Or Cmi Audio Codec Driver
1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click Next, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. Avance Audio Rack table can play CD, WAV, 6. - Page 41 1. Click SOUND when MAGIC INSTALL 2. Choose Install component in Installation MENU appears Package 3. Click Next when copyright Issue appears, click 4. Enter Program folders name or click Next Next or choose BROWSE to change the path for the file to be store 5.
-
Page 42: Lan
7. C-Media Media Rack Play table 8. C-Media Audio Configuration setting 9. C-Media Multi-Channel Audio Demo Program, 10. When Enabled XeaR, you can plug earphone you can Test speaker position in Speak-Out connector as a Rear speaker, and 2-channel speaker plug in Line-In as Front Speaker to get 4-channel effect 4-3 LAN Install RTL8100 LAN Controller Driver... -
Page 43: Pc-Health Intel 845 Pc-Health Monitor
3. Driver install Finish, Click YES, restart the 4. After restart computer, Window can find computer Realtek RTL8139C PCI Fast Ethernet NIC 5. Select the best driver for your device, Select 6. After restart computer you can check in NEXT, Add New Hardware Wizard Find control Panel\System Device Manager\ NETRTS5.INF Select NEXT Network adapters to make sure LAN card... - Page 44 3. Click Next to continue installation 4. Select Program Group name or enter a new group name, click Next, and click Finish after setup complete. 4-4-1 How To Utilize PC-HEALTH 1. Click Program → Winbond Hardware Doctor 2. After executing Winbond Hardware Doctor it →...
-
Page 45: Magic Bios Install Bios Live Update Utility
4-5 MAGIC BIOS Install BIOS Live Update Utility Click Magic BIOS when Magic Install Click Next to install the Magic BIOS in MENU appears Destination Folder After finish Setup you will have a Magic Double click the Magic BIOS icon you will BIOS icon in your screen have this picture, choose from internet you can upgrade BIOS On-line... -
Page 46: Iaa Install Intel Application Accelerator Software
Click Yes if you want to update the BIOS When System programming BIOS don’t turn otherwise choose No to exit off power, after finish update BIOS, the system will clear CMOS and automatically Restart When choose From Local Driver to update 10. -
Page 47: Pc-Cillin Install Pc-Cillin2002 Anti-Virus Program
4-7 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PC- MENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PC- CILLIN 2002" (2) Click Open Manual. you can learn PC- CILLIN 2002 how to use 3. -
Page 48: How To Disable On-Board Sound
7. After PC-CILLIN 2002 complete, Please 8. finish register process, we recommend select register your information and get LICENSE update item ro download newest engine code KEY from TREND MICRO web site, enter and virus code your license key and click FINISH Note : Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.exe...