Table of Contents
Advertisement
Quick Links
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Whistler PRO-3600
Summary of Contents for Whistler PRO-3600
- Page 1 Installation Instructions Pro-3600 Laser/Radar Detector THE WHISTLER GROUP, INC. CORPORATE HEADQUARTERS 3604 NW Frontage Rd. Bentonville, AR 72712 TEL 479.273.6012 FX 479.273.2927 P/N 202903 © The Whistler Group, Inc 2010 www.whistlergroup.com www.whistlergroup.com...
-
Page 2: Table Of Contents
TOOLS REQUIRED TABLE OF CONTENTS Topic Page Tools Required For Installation • Phillips Screwdriver Tools Required • 3/8" Open End Wrench Components 3 - 4 • Electric Drill • Drill Bit: 1/4’, 13/64",15/32” and #32 Bit Mounting Brackets • Other Tools May Be Required Based On Your Vehicle Type Or Mounting Fasteners Requirements For Customized Installation Installation of Laser/Radar Antenna... - Page 3 Pro-3600 COMPONENTS Pro-3600 COMPONENTS INTRODUCTION Interface Cable...
-
Page 4: Mounting Brackets
MOUNTING BRACKETS MOUNTING FASTENERS... -
Page 5: Installation Of Laser/Radar Antenna
INSTALLATION OF LASER/RADAR ANTENNA INSTALLATION OF LASER/RADAR ANTENNA General Information The laser/radar antenna is waterproof and designed to be mounted at the front of your vehicle. Optimum mounting location is near the license plate area. Since this module also includes a Laser receiver, the front of this module needs to “look”... - Page 6 INSTALLATION OF LASER/RADAR ANTENNA INSTALLATION OF LASER/RADAR ANTENNA Large L and small L brackets maybe used in combination in a variety of differnet ways. The Small L Brackets are fastened to the Large L Bracket using the #10-32 x 1/2" bolts, #10-32 nuts and lock washers. To fasten the Large L or Small L Brackets to your vehicle, mark the supporting structure through the appropriate holes in the (ANTENNA window should not be angled up toward the sky,...
- Page 7 INSTALLATION OF LASER/RADAR ANTENNA INSTALLATION OF LASER/RADAR ANTENNA Mount the antenna to the vehicle such that the ANTENNA Antenna Cable to the Interface Box (iBox) window is facing the road surface, sky, right or left of the Once the antenna is installed, connect the antenna cable to vehicle, and the reflector has an unobstructed view of the the quick disconnect interface cable.
-
Page 8: Installation Of Optional Laser Antenna
INST ALLA TION OF INTERFACEBOX INST ALLA TION OF OPTIONAL LASER ANTENNA Mounting the Interface Box (iBox) Optional Laser Antenna The iBox provides a central location for the connection of all The LRM-360 provides both front and rear laser available modules. reception. -
Page 9: Installation Of Control Panel
INST ALLA TION OF OPTIONAL LASER ANTENNA INST ALLA TION OF CONTROL PANEL Installing the Laser Antenna - Continued Installing the Control Panel Using Hook & Loop Fasteners, the laser antenna may also The control panel may be mounted using the through Dash Bracket or supplied double sided tape. -
Page 10: Laser/Radar Antenna
Whistler retailers or directly from Whistler; ask for the Part (remember the unit needs to be able to “see” the sky). Number SWRA-36. -
Page 11: Power Connection
POWER CONNECTION ERROR CODES Power Cable Connection The codes listed below will be displayed if there is any trouble with the unit. The iBox has the power cable attached to it. The ground wire has a “U” type connector which should be fastened to a metal surface that is grounded to the vehicle. -
Page 12: Troubleshooting Guide
ACCESSORIES TROUBLESHOOTING PROBLEM: No display or audio. The following accessories can be ordered directly from Whistler by calling • Check fuse in power cable,(4 amp) replace if necessary. 1-800-531-0004 or visit our online store at www.whistlergroup.com • Check fuse in fuse box, replace if necessary. - Page 13 THROUGH DASH BRACKET THROUGH DASH BRACKET How to install the Console Cradle Copy cut-out template. Carefully remove section marked “CUTOUT”. Tape template to desired vehicle mounting location. Trace cutout area. Carefully cut/remove dashboard or vehicle material. Trim “hole” to ensure snug fit of cradle. Insert M4.0x20 mm bolt into cradle.