Page of 6
Download Bookmark Comment

Pioneer DEH-2950MP Installation Manual

Installation manual.
Also See for DEH-2950MP:
Operation manual - 52 pages
DEH-2950MP
DEH-1950
DEH-1950G
This product conforms to new cord colors.
Los colores de los cables de este producto se
conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo
padrão de cores.
Printed in Thailand
<CRD4139-A/N> ES
<KSNNX> <06H00000>
Installation
Note:
DIN Front-mount
Check all connections and systems before final
installation.
Installation with the rubber bush
Do not use unauthorized parts. The use of
Mounting sleeve
unauthorized parts may cause malfunctions.
Dashboard
Consult with your dealer if installation requires
drilling of holes or other modifications of the
182
vehicle.
Rubber bush
53
Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
Screw
of a sudden stop.
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
1. Insert the mounting sleeve into the dashboard.
Optimum performance is obtained when the unit
When installing in a shallow space, use a sup-
is installed at an angle of less than 60°.
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
60°
2. Secure the mounting sleeve by using a screwdriv-
er to bend the metal tabs (90°) into place.
3. Install the unit as illustrated.
Removing the Unit
When installing, to ensure proper heat dispersal
1. Extend top and bottom of the trim ring outwards
when using this unit, make sure you leave ample
to remove the trim ring. (When reattaching the
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
trim ring, point the side with a groove down-
wards and attach it.)
It becomes easy to remove the trim ring if the
DIN Front/Rear-mount
front panel is released.
This unit can be properly installed either from
Trim ring
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.
2. Insert the supplied extraction keys into both sides
of the unit until they click into place.
3. Pull the unit out of the dashboard.
ENGLISH
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. (When reattaching the
trim ring, point the side with a groove down-
wards and attach it.)
It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.
3. Tighten two screws on each side.
Use either truss screws (5 mm × 8 mm) or
flush surface screws (5 mm × 9 mm), depend-
ing on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket

   Also See for Pioneer DEH-2950MP

   Summary of Contents for Pioneer DEH-2950MP

  • Page 1

    • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places DEH-2950MP such as near the heater outlet. 1. Insert the mounting sleeve into the dashboard. • Optimum performance is obtained when the unit •...

  • Page 2

    Instalación ESPAÑOL Instalação PORTUGUÊS (B) Nota: 1. Inserte el manguito de montaje en el tablero de Montaje trasero DIN Nota: 1. Insira a manga de montagem no painel de instru- Montagem traseira DIN instrumentos. mentos. • Verifique todas las conexiones y sistemas antes •...

  • Page 3

    WOÐdFë VOÂd²Ã« ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ fO¹UIÄ V Š wHKš VOÂdð fO¹UIÄ V Š wÄUÄ_« VOÂd²Ã« • WOÞ UD*« W³K'« lÄ VOÂd²Ã« • VO d²Ã« »« dł •  «œ«bFë WŠ uà • • — WOÞUDÄ W³Kł — bO−Mð ‚uÞ •...

  • Page 4

    Connecting the Units ENGLISH Note: • Control signal is output through blue/white cable Connection Diagram (Fig. 1) • When this unit is installed in a vehicle without when this unit is powered on. Connect it to an 5. Connect with RCA cables ACC (accessory) position on the ignition switch, external power amp’s system remote control or 1.

  • Page 5

    Conexión de las unidades Conexão dos componentes ESPAÑOL PORTUGUÊS (B) Nota: • La señal de control se emite a través del cable Diagrama de conexión (Fig. 1) Nota: • O sinal de controle é emitido através do cabo Diagrama de conexão (Fig. 1) •...

  • Page 6

    • • • • • — • — • — — — — — — — — — — —...

Comments to this Manuals

Symbols: 0
Latest comments: