BENDIX TU-FLO 700 COMPRESSOR Manual page 14

Introduction to the Air Brake Charging System
Powered by the vehicle engine, the air compressor
builds the air pressure for the air brake system. The
air compressor is typically cooled by the engine coolant
system and lubricated by the engine oil supply.
The compressor's unloader mechanism and governor
(along with a synchro valve for the Bendix
596 air compressor) control the brake system air
pressure between a preset maximum and minimum
pressure level by monitoring the pressure in the service
(or "supply") reservoir. When the air pressure becomes
greater than that of the preset "cut-out", the governor
controls the unloader mechanism of the compressor
to stop the compressor from building air and also
causes the air dryer to purge. As the service reservoir
air pressure drops to the "cut-in" setting of the governor,
the governor returns the compressor back to building
air and the air dryer to air drying mode.
As the atmospheric air is compressed, all the water
vapor originally in the air is carried along into the air
system, as well as a small amount of the lubricating oil
as vapor.
The duty cycle is the ratio of time the compressor
spends building air to the total engine running time.
Air compressors are designed to build air (run "loaded")
up to 25% of the time. Higher duty cycles cause
conditions that affect air brake charging system
performance which may require additional
maintenance. Factors that add to the duty cycle are:
air suspension, additional air accessories, use of an
undersized compressor, frequent stops, excessive
leakage from fittings, connections, lines, chambers or
valves, etc.
The discharge line allows the air, water-vapor and
oil-vapor mixture to cool between the compressor and
Discharge Optional "Ping" Tank
Line
Compressor
14
® DuraFlo
Air Dryer
Governor
(Governor plus Synchro valve
™
for the Bendix ® DuraFlo 596
Compressor)
air dryer. The typical size of a vehicle's discharge line,
(see column 2 of Table A on page 15) assumes a
compressor with a normal (less than 25%) duty cycle,
operating in a temperate climate. See Bendix and/or
other air dryer manufacturer guidelines as needed.
™
When the temperature of the compressed air that enters
the air dryer is within the normal range, the air dryer can
remove most of the charging system oil. If the
temperature of the compressed air is above the normal
range, oil as oil-vapor is able to pass through the air
dryer and into the air system. Larger diameter discharge
lines and/or longer discharge line lengths can help reduce
the temperature.
The discharge line must maintain a constant slope
down from the compressor to the air dryer inlet fitting
to avoid low points where ice may form and block the
flow. If, instead, ice blockages occur at the air dryer
inlet, insulation may be added here, or if the inlet fitting
is a typical 90 degree fitting, it may be changed to a
straight or 45 degree fitting. For more information on
how to help prevent discharge line freeze-ups, see
Bendix Bulletins TCH-08-21 and TCH-08-22 (see
pages 31-33). Shorter discharge line lengths or
insulation may be required in cold climates.
The air dryer contains a filter that collects oil droplets,
and a desiccant bed that removes almost all of the
remaining water vapor. The compressed air is then
passed to the air brake service (supply) reservoir. The
oil droplets and the water collected are automatically
purged when the governor reaches its "cut-out" setting.
For vehicles with accessories that are sensitive to small
amounts of oil, we recommended installation of a
Bendix PuraGuard
®
the amount of oil present.
The Air Brake Charging System
compressed air for the braking system as well as other
air accessories for the vehicle. The system usually
consists of an air compressor, governor, discharge line,
air dryer, and service reservoir.
Optional Bendix
System Filter or PuraGuard
QC
Service Reservoir
™
(Supply Reservoir)
system filter, designed to minimize
®
supplies the
®
PuraGuard
™ Oil Coalescing Filter
Reservoir Drain
®
®