Advertisement
SSC-1000 (gb)
2009.1.8
1:38 PM
User's Guide
* DATA BACK-UP
In case changing the camera by
downloading the set-up data of the
Samsung Dome Camera, this is a
function for applying the set-up value set
up in the changed camera just the way it
is. In order to perform this mode, move
CURSOR( ) to the DATA BACK-UP in
the CAMERA SET MENU, and press the
ENTER button. If you want to go back to
the main menu, press the MENU button.
In this mode, the menu will appear only if the protocol is set to
"SAMSUNG", where you can backup data.
*-1 In order to initialize the camera
connected to the controller,
move CURSOR( ) to CAM RESET,
and press the ENTER button.
*-2 When downloading the set-up data
of the camera, move CURSOR( )
to DOWNLOAD, and press the
ENTER button.
*-3 When you wan to set the set-up data
downloaded to the camera,
move CURSOR( ) to UPLOAD,
and press the ENTER button.
( SYSTEM INFO
You can check SSC-1000 for the
communication settings and the firmware
version. Press the MENU button to
return to the previous menu.
) MULTIPLEX CONTROL
When you press "MUX CONTROL"
button, you can control Multiplex.
If communication error occurs, 'ERR' message appears on the second
right line of the LCD for a moment, and then disappears.
Page 16
M ON = [ 0 0 ]
CAM RESET
DOWN LOAD
UP
LOAD
M ON = [ 0 0 ]
CAM RESET
MON = [00]
DOWN LOADING . . .
120 SEC LEFT.
MON = [00]
UP LOADING . . .
120 SEC LEFT.
SYSTEM INFO
BAUDRATE : 9600
PROTOCOL : SAMSUNG
F/W V2.00 - 080812
M ON = [ 0 01]
MULTIPLEX CONTROL
16
2) Manipulating the camera
CAM=[ 0 0 0 ]
! For manipulating the camera, since only the concerned cam no. indicated in LCD is
@ In the third line of LCD, the camera's action state gets indicated. Initially, it appears
# AUTO PAN action
CAM=[ 0 0 0 ]
$ SCAN action
CAM = [000]
CAM = [000]
% PATTERN action
^ PRESET action
CAM=[ 0 0 0 ]
possible, first select the camera you want to manipulate. For camera selection, when
you press CAM+NO+ENTER the camera no. gets indicated in LCD.
as "MANUAL". And, in this state, by using the JOY STICK and LENS CONTROL
buttons, you can manipulate the light turning mark and the lens. According to the
manipulation angle of the Joy Stick, the rotation speed of the light turning mark gets
varied.
AUTO PAN enables you to move the camera between two preset points you set in
the menu If you want to perform Auto Pan, press the AUTO PAN button in Manual
mode and enter a desired AUTOPAN number, then press the ENTER button. Then,
the LED indicator on the AUTO PAN button flashes with a message of "AUTO PAN
[ ]". To deactivate AUTO PAN, press the AUTO PAN button again.
You can scan for multiple preset positions in sequence as set in Scan mode. In
Manual mode, enter a desired SCAN number and press the ENTER button to start
the scan function. Then, the LED indicator on the SCAN button flashes with a
message of "SCAN [ ]". To release Scan mode, press the SCAN button again.
This is a function for watching 30 seconds of the camera's moves set up by the user
according to the camera's pattern mode set-up. Press the PATTERN button in the
manual state, put in the pattern no. you want, and when you press the ENTER
button pattern action gets performed. At this time, the LED of the PATTERN button
gets turned on, and "Pattern [ ]" gets indicated in the LCD. If you want to cancel
the pattern action, press the PATTERN button once again.
This is a function for selecting and watching the preset position set up in the camera.
If you want to select the PRESET Position you want, press the PRESET button, put in
the appropriate number in the position you want, and press the ENTER button. At this
time, the LED of the PRESET button gets turned on, "Pattern [ ]" gets indicated in
the LCD. Once the operation is finished, current move is changed to MANUAL MODE.
17
Hide quick links:
Advertisement
