Enabling Sleep; Disabling The Sleep Timer; Using Learning; Learning Precautions - Radio Shack 15-2146 - Voice Prompt Universal Remote Owner's Manual

2. Press the Sleep key until the desired time is
set. The timer increases by 15 minutes each
time you press the key, up to 60 minutes.
When the timer counts down to 0, the remote sends
a "power off " signal to the selected device.
The sleep timer will work even if you have
reassigned the mode key to a different mode (see
"Reassigning Device Keys" on page 11).
If you turn off the device yourself, the sleep timer
turns off as well.
E S
NABLING LEEP
If the SLEEP key does not operate your device's
built-in sleep timer or if your device does not have a
sleep mode, you must enable the sleep timer for
that mode:
Press and hold SETUP until you hear the
1.
programming menu, then press 4.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
At the prompt, press 1.
2.
At the prompt, press a device key (i.e., CBL/
3.
SAT, AUX, TV, DVD, AUDIO, or VCR). The LED
blinks twice and the remote says "Success"
and returns to the programming menu.
4. Press 4 and repeat steps 2 and 3 for another
device or press and hold BACK to exit
programming.
D S T
ISABLING THE LEEP
To disable the sleep timer for a mode:
1. Press and hold SETUP until you hear the
programming menu, then press 4.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
2. At the prompt, press 2.
3. At the prompt, press a device key (i.e., CBL/
SAT, AUX, TV, DVD, AUDIO, or VCR). The LED
blinks twice and the remote says "Success"
and returns to the programming menu.
4. Press 4 and repeat steps 2 and 3 for another
device or press and hold SETUP to exit
programming.

USING LEARNING

The RadioShack 6-in-1 Easy Setup Voice Remote
includes a Learning feature so you can add
functions that are unique to your home
entertainment devices (e.g.,VCR Tracking Up or
Down).However, there are some considerations:
IMER
L P
EARNING RECAUTIONS
• Your original remote controls must be in
working order for learning to work properly.
• Learned keys are mode specific, so each one
can store a unique function for each mode.
• Learned keys can be used in macros (see Using
Macros on page 8).
• Do not use the following keys for learning:
Device Keys, SETUP, BACK, REPEAT, FAV SCAN,
SLEEP, or Record (•) Key.
• Learning capacity is approximately 16 to 25
keys, depending on the code being learned.
• Certain device codes are not learnable
including multi-frequency types, some high
frequency ones, and other unusual formats.
• For optimum learning, avoid high levels of
ambient light such as natural sunlight or
energy-efficient fluorescent lights.
NOTE: Please have your original remote controls
handy before programming learning.
P L
ROGRAMMING A EARNED
1. Press and hold SETUP until you hear the
programming menu, then press 5.
NOTE: If more than 15 seconds pass between key
presses, the remote says "Goodbye" and exits
programming.
2. At the prompt, press 1 to learn a function.
3. At the prompt, press a device key once (i.e.,
CBL/SAT, AUX, TV, DVD, AUDIO, or VCR) to assign
a mode for learning.
4. Place the RadioShack 6-in-1 Easy Setup Voice
Remote head-to-head (about 2" apart) from
your original remote control. Also locate the
key (on your original remote control) that will
serve as the teaching function.
5. On the RadioShack 6-in-1 Easy Setup Voice
Remote, press a key where the learned
function will be stored.
6. On the original remote, press and hold the key
to be learned. The RadioShack 6-in-1 Easy
Setup Voice Remote's LED will turn off.
Continue holding the key on the original
remote until the RadioShack 6-in-1 Easy Setup
Voice Remote's LED blinks twice, and the
remote says "Success" and returns to the
prompt for step 3.
O ' M
WNER S ANUAL
K
EY
2"
Using Learning 9