Table of Contents
Advertisement
Quick Links
BLUE-FLAME VENT-FREE
PROPANE/LP GAS HEATER
OWNER'S OPERATION AND INSTALLATION MANUAL
®
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
— Installation and service must be performed by a qualified installer, service
agency, or the gas supplier.
This appliance may be installed in an aftermarket* manufactured (mobile) home,
where not prohibited by state or local codes.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
Model: RP30C and CGP18C
Save this manual for future reference.
Advertisement
Table of Contents
Related Manuals for Desa CGP18C
Summary of Contents for Desa CGP18C
- Page 1 BLUE-FLAME VENT-FREE PROPANE/LP GAS HEATER OWNER’S OPERATION AND INSTALLATION MANUAL Model: RP30C and CGP18C ® WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
-
Page 2: Table Of Contents
CONTENTS SAFETY INFORMATION SECTION Safety Information ... 2 Product Identification ... 4 Local Codes ... 4 Unpacking ... 4 Product Features ... 4 Air For Combustion And Ventilation ... 5 Installing To Wall ... 9 Connecting To Gas Supply ... 14 Checking Gas Connections ... - Page 3 SAFETY INFORMATION Continued 101805 WARNINGS WARNING ICON G 001 WARNING: Any change to this heater or its controls can be dangerous. 1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. 2.
-
Page 4: Product Identification
Piezo Ignition System This heater has a piezo ignitor. This system requires no matches, batteries, or other sources to light heater. Ignitor Button Control Knob Grill Guard Heat Shield (RP30C) or Glass Panel (CGP18C) Heater Cabinet 101805... -
Page 5: Air For Combustion And Ventilation
AIR FOR COMBUSTION VENTILATION 101805 WARNING ICON This heater shall not be installed in a confined space unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home. Today’s homes are built more energy efficient than ever. - Page 6 AIR FOR COMBUSTION VENTILATION Continued DETERMINING AIR FLOW FOR HEATER LOCATION Determining if You Have a Confined or Unconfined Space Use this worksheet to determine if you have a confined or unconfined space. Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.
- Page 7 AIR FOR COMBUSTION VENTILATION Continued 101805 WARNING ICON If the area in which the heater may be operated is smaller than that defined as an unconfined space, provide adequate combus- tion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3.
- Page 8 AIR FOR COMBUSTION VENTILATION Continued Ventilation Air From Outdoors Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces.
-
Page 9: Installing To Wall
Maintain the minimum clearances shown in Figure 4 (page 10). If you can, provide greater clearances from floor, ceiling, and joining wall. You can locate model CGP18C on floor, away from a wall. An optional floor mounting stand is needed. Purchase the floor mounting stand from your dealer. See Accessories, page 27. - Page 10 CEILING 6" Minimum From Sides Of Heater Left Side FLOOR Figure 4 - Mounting Clearances As Viewed From Front of Heater CAUTION 36" Minimum Right Side Minimum To Floor " - RP30C *3" - CGP18C 101805...
- Page 11 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forward, then down. 4. Remove cardboard packing from grill and glass (CGP18C) or heat shield (RP30C). FRONT PANEL REMOVAL G...
- Page 12 Figure 8 - Folding Anchor 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. WARNING 7 1/4" 16" Min. Only Insert Mounting 32 1/2" Screws Through Last Min. Hole On Each End Floor CGP18C 18 3/4" Min. 101805...
- Page 13 INSTALLING TO WALL Continued 101805 4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT: For thick walls (over 1/2" thick) or solid walls, do not pop open wings. Figure 9 - Popping Open Anchor Wings For Thin Walls 5.
-
Page 14: Connecting To Gas Supply
CONNECTING TO GAS SUPPLY A qualified service person must connect heater to gas supply. Follow all local codes. WARNING ICON Never connect heater directly to the propane/LP supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane/LP supply. The installer must supply an external regulator. -
Page 15: Checking Gas Connections
CONNECTING TO GAS SUPPLY Continued CHECKING CONNECTIONS 101805 Hold pressure regulator with wrench when connecting it to gas piping IMPORTANT: and/or fittings. Pressure Regulator 1/2" NPT Pipe Nipple Tee Joint Test Reducer Bushing to Gauge 1/8" NPT Connection * 1/8" NPT Plug Tap Tee Joint Sediment... - Page 16 CHECKING CONNECTIONS Continued 3. Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve. 4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak. 5.
-
Page 17: Operating Heater
OPERATING HEATER 101805 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING ICON G 001 If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. - Page 18 OPERATING HEATER Continued 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information at the top of page 17. If you don’t smell gas, go to the next step. 5.
-
Page 19: Inspecting Burner
OPERATING HEATER Continued INSPECTING BURNER 101805 TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise 2. Press in control knob and turn clockwise 3. Turn off all electric power to the appliance if service is to be performed. Shutting Off Burner Only (pilot stays lit) 1. - Page 20 INSPECTING BURNER Continued If pilot flame pattern is incorrect, as shown in Figure 19 • turn heater off (see To Turn Off Gas to Appliance, page 19) • see Troubleshooting, pages 21 through 24 BURNER FLAME PATTERN Figure 20 shows a correct burner flame pattern. Figure 21 shows an incorrect burner flame pattern.
-
Page 21: Cleaning And Maintenance
CLEANING MAINTENANCE TROUBLE- SHOOTING Note: All troubleshooting items are listed in order of operation. 101805 WARNING ICON G 001 Turn off heater and let cool before cleaning. WARNING ICON G 001 You must keep control areas, burner, and circulating air passageways of heater clean. - Page 22 TROUBLE- SHOOTING Continued OBSERVED POSSIBLE PROBLEM CAUSE When ignitor button 1. Gas supply turned off is pressed, there is or manual shutoff spark at ODS/pilot valve closed but no ignition 2. Control knob not in PILOT position 3. Control knob not pressed in while in PILOT position 4.
- Page 23 TROUBLE- SHOOTING Continued 101805 OBSERVED POSSIBLE PROBLEM CAUSE Burner does not light 2. Burner orifice diameter after ODS/pilot is lit is too small (continued from 3. Inlet gas pressure is page 22) too low Delayed ignition of 1. Manifold pressure is burner too low 2.
- Page 24 TROUBLE- SHOOTING Continued WARNING ICON G 001 If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone.
-
Page 25: Technical Service
SERVICE SPECIFICATIONS SERVICE HINTS 101805 You may have further questions about installation, operation, or troubleshooting. If so, contact DESA International’s Technical Service Department at 1-800-323-5190. Btu (Variable) Type Gas Ignition Pressure Regulator Setting Inlet Gas Pressure (inches of water) Maximum... -
Page 26: Replacement Parts
Parts Under Warranty Contact authorized dealers of this product. If they can’t supply original replacement part(s), either contact your nearest Parts Central (see below) or call DESA International’s Technical Service Department at 1-800-323-5190. When calling, have ready •... -
Page 27: Accessories
Purchase these heater accessories from your local dealer. If they can not supply these accessories, either contact your nearest Parts Central (see page 26) or call DESA International’s Parts Department at 1-800-972-7879 for information.You can also write to the address listed on the back page of this manual to receive these accessories. -
Page 29: Parts List
RP30C PARTS LIST 10-1 10-2 101805 This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. PART NUMBER DESCRIPTION 098304-01 Screw, #10 x 3/8" 098345-01AC Front Panel 098197-04 Grill Guard... - Page 31 CGP18C PARTS LIST 12-1 12-2 101805 This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. PART NUMBER DESCRIPTION 098304-01 Screw, #10 x 3/8" 098742-03...
-
Page 32: Warranty Information
COMFORT GLOW VENT-FREE HEATERS DESA International warrants this product to be free from defects in materials and components for one (1) year from the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.