Connections - Denon AVR-2805 Operating Instructions Manual

5

CONNECTIONS

• Do not plug in the AC cord until all connections
have been completed.
• Be sure to connect the left and right channels
properly (left with left, right with right).
• Insert the plugs securely. Incomplete connections
will result in the generation of noise.
• Use the AC OUTLET for audio equipment only.
Do not use them for hair driers, etc.
Connecting the audio components
• When making connections, also refer to the operating instructions of the other components.
Connecting a CD player
CD player
OUTPUT Connect the CD player's analog
R L
output jacks
OUTPUT) to this unit's CD jacks
DIGITAL AUDIO DIGITAL AUDIO
R L
using pin plug cords.
Connecting a turntable
Turntable
(MM cartridge)
Connect the turntable's output cord to the AVR-
2805's PHONO jacks, the L (left) plug to the L jack,
the R (right) plug to the right jack.
NOTE:
This unit cannot be used with MC cartridges
directly. Use a separate head amplifier or step-up
transformer.
If humming or other noise is generated when the
ground wire is connected, disconnect the ground
wire.
Ground wire
R R R L
R
L
L
R
R L
CD player or other component
equipped with digital output jacks
DIGITAL AUDIO DIGITAL AUDIO
OPTICAL COAXIAL
OUTPUT
MD recorder, CD recorder or other component
equipped with digital input/output jacks
B
INPUT OUTPUT
OPTICAL
Connecting the DIGITAL jacks
Use these for connections to audio equipment with digital output. Refer
to "Setting the Digital in Assignment". (See page 22)
NOTES:
• Use 75 Ω/ohms cable pin cords for coaxial connections.
• Use optical cables for optical connections, removing the cap before
connecting.
• Note that binding pin plug cords together with AC
cords or placing them near a power transformer
will result in generating hum or other noise.
• Noise or humming may be generated if a
connected audio equipment is used independently
without turning the power of this unit on. If this
happens, turn on the power of the this unit.
Connecting the AC OUTLET
AC OUTLET
• SWITCHED
(ANALOG
(total capacity – 100 W)
The power to these outlets is turned on and off in conjunction with
the POWER operation switch on the main unit, and when the power
is switched between on and standby from the remote control unit.
No power is supplied from these outlets when this unit's power is
at standby. Never connect equipment whose total capacity is above
100 W.
NOTE:
Only use the AC OUTLET for audio equipment. Never use them for
hair driers, TVs or other electrical appliances.
Connecting the pre-out jacks
Use these jacks if you wish to connect external power
amplifier(s) to increase the power of the front, center and
surround sound channels, or for connection to powered
loudspeakers.
To use Surround back with one speaker, connect the
speaker to SURR. BACK L CH.
Route the connection cords, etc., in
such a way that they do not obstruct
the ventilation holes.
Power supply cord
TRIGGER OUT
AC 230V, 50Hz
Turn the DC 12V voltage on and off for the individual functions.
For details, see "Setting the Trigger Out Setup". (See page 26)
R L R L
B NOTE:
If humming noise is generated by a
R L R L
INPUT OUTPUT
tape deck, etc., move the tape deck
CD recorder or Tape deck
away.
Connecting a tape deck
Connections for recording:
Connect the tape deck's recording input jacks (LINE IN or REC) to this unit's
tape recording (CDR/TAPE OUT) jacks using pin plug cords.
Connections for playback:
Connect the tape deck's playback output jacks (LINE OUT or PB) to this
unit's tape playback (CDR/TAPE IN) jacks using pin plug cords.
Connecting the video components
• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can
result in a drop in video quality.
• When making connections, also refer to the operating instructions of the other components.
• The AVR-2805 is equipped with a function for up-converting video signals.
• The signal connected to the video signal terminal is output to the S-Video and component video monitor out
terminals.
• The REC OUT terminals have no conversion function, so when recording only connect the video terminals.
TV or DBS tuner Connecting a TV or DBS tuner
AUDIO
VIDEO TV or DBS
B
OUT
R L OUT
• Connect the TV's or DBS tuner's video output jack (VIDEO OUTPUT) to the
IN jack using a 75 Ω/ohms video coaxial pin plug cord.
R L
• Connect the TV's or DBS tuner's audio output jacks (AUDIO OUTPUT) to the
using pin plug cords.
AUDIO
VIDEO
B
OUT DVD player or video disc player (VDP), etc.
R L OUT
R L
Connecting a DVD player or a video disc player (VDP)
DVD
• Connect the video disc player's video output jack (VIDEO OUTPUT) to the
video coaxial pin plug cord.
• Connect the video disc player's analog audio output jacks (ANALOG AUDIO OUTPUT) to the
pin plug cords.
• VDP can be connected to the VDP jacks in the same way.
R
L
R
L
L
R
R
L
R L
R L
Video deck 2
R L R L
R L R L OUT IN
OUT IN
VIDEO
AUDIO
Video deck 1
R L R L
R L R L OUT IN
OUT IN
VIDEO
AUDIO
Connecting a video decks
• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
• Connect the video deck's video output jack (VIDEO OUT) to the
(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.
VIDEO
Connecting the audio output jacks
• Connect the video deck's audio output jacks (AUDIO OUT) to the
VCR-1 OUT jacks using pin plug cords.
Connect the second video deck to the VCR-2 jacks in the same way.
VIDEO
AUDIO
(yellow) DVD IN jack using a 75 Ω/ohms
VIDEO
AUDIO
VIDEO
IN
Monitor TV
MONITOR OUT
• Connect the TV's video input jack (VIDEO INPUT) to the
MONITOR OUT jack using a 75 Ω/ohms video
VIDEO
coaxial pin plug cord.
Note on connecting the digital input jacks
• Only audio signals are inputs to the digital
input jacks. For details. (See page 5)
VIDEO (yellow) VCR-1 IN jack, and the video deck's video input jack (VIDEO IN) to the
AUDIO VCR-1 IN jacks, and the video deck's audio input jacks (AUDIO IN) to the
ENGLISH
(yellow) TV or DBS
TV or DBS IN jacks
DVD IN jacks using
AUDIO
5