Multi Zone; Zone2/Rec Select Button - Denon AVR-2805 Operating Instructions Manual

ENGLISH
10

MULTI ZONE

Multi-zone playback with multi-source
MULTI ZONE MUSIC ENTERTAINMENT SYSTEM
• When the outputs of the "ZONE2" OUT terminals are wired and connected to integrated amplifiers installed
in other rooms, different sources can be played in rooms other than the main zone in which this unit and the
playback devices are installed. (Refer to ZONE2 on the diagram below.)
• ZONE2 SPEAKER OUT can be used when "ZONE2" is selected at System Setup Menu "Power Amp
Assign".In this case, Surround Back Speaker OUT cannot be used for MAIN ZONE. (See page 25.)
To control playback devices other than the ones above, either use that device's remote control unit or preset
a separately sold programmable remote control unit.
NOTES:
• For the AUDIO output, use high quality pin-plug cords and wire in such a way that there is no humming or
noise.
• For instructions on installation and operation of separately sold devices, refer to the devices' operating
instructions.
• When the PURE DIRECT mode is set for the main zone, no signals are output to the ZONE2 video
terminals.
• Signals are output from the ZONE2 video terminals even when ZONE2 is set to "OFF".
MULTI ROOM MUSIC ENTERTAINMENT SYSTEM
[Multi-zone playback using the ZONE2 PRE OUT terminals]
2 When using the SURR. BACK amplifier as the SURROUND BACK.
The AVR-2805 is equipped with pre-out terminals for which the volume is adjustable (ZONE2) and composite
video output terminals as the ZONE2 output terminals.
System configuration and connections example.
Using external amplifier
MAIN ZONE 7.1-channel systems
FL
Center
This unit
DVD player
B
ENTER CH SEL
Input
ZONE2 AUDIO OUT
(VARIABLE OUT)
SL
SBL
SYSTEM REMOTE
CONTROL UNIT
RC-975
38
Monitor ZONE 2
Monitor
FR
ZONE2 VIDEO OUT
SW B
Pre-main amplifier or
power amplifier
SR
SBR
MULTI SOURCE AUDIO signal cable
ZONE2 VIDEO signal cable
* Refer to CONNECTIONS on pages 5 to 9.
2 When using the SURR. BACK amplifier as the ZONE2.
• ZONE2 speaker out can be used when "ZONE2" is selected at System Setup Menu "Power Amp Assign".
In this case, Surround Back PREOUT and speaker out cannot be used for MAIN ZONE.
• The AVR-2805 is equipped with preout terminals for which the volume is adjustable (ZONE2) and speaker
out terminals for which the volume is adjustable (ZONE2) and composite video output terminals as the
ZONE2 output terminals.
System configuration and connections example.
Using this unit's internal amplifier as the ZONE2.
MAIN ZONE 5.1-channel systems
Monitor
FL
C
This unit
DVD player
B
CH SEL ENTER
Input
SL
SYSTEM REMOTE
CONTROL UNIT RC-975
[1] Outputting a program source to an amplifier, etc., in a different room (ZONE2 mode)
1
Press the POWER switch
(button).
(Main unit)
2
Press the ZONE2 / REC
SELECT button.
ZONE 2 /
REC SELECT The display switches as
follows each time the button
(Main unit)
is pressed.
ZONE2 RECOUT
3
With "ZONE2 SOURCE"
FUNCTION
displayed, turn
FUNCTION knob and select
the source you wish to
output.
(Main unit)
• The display switches the
selected source.
4
Start playing the source to be output.
• For operating instructions, refer to the
manuals of the respective components.
5
To cancel, turn the function
FUNCTION
knob and select "SOURCE".
(Main unit)
SPEAKER cable
ZONE2 VIDEO signal cable
FR
* Refer to CONNECTIONS on pages 5 to 9.
SW
ZONE2 SPEAKER OUT
ZONE 2
VIDEO OUT
SR
Monitor
ZONE 2
2
3, 5 1
Display
the
NOTES:
• The signals of the source selected in the ZONE2
mode are also output from the VCR-1, VCR-2 and
CDR/TAPE recording output jacks.
• Digital signals are not output from the ZONE2
audio output jacks.
• Refer to page 38 about the MULTI ZONE
connections.