Cw Delay Time Setting; Cw Pitch Adjustment - Yaesu FT-950 Operating Manual

Hf/50 mhz transceiver
Hide thumbs Also See for FT-950:
Table of Contents

Advertisement

CW C
ONVENIENCE
During semi-break-in (not QSK) operation, the hang time of the transmitter, after you have finished sending, may be
adjusted to a comfortable value consistent with your sending speed. This is the functional equivalent of the "VOX Delay"
adjustment used on voice modes, and the delay may be varied anywhere between 30 msec and 3 seconds via Menu item
"044 A1A DELAY
044 A1A DELAY
044 A1A DELAY
044 A1A DELAY".
044 A1A DELAY
1. Press the [ BK-IN ] button to enable CW transmission
(Menu item "043 A1A BK-IN
043 A1A BK-IN" must be set to "SEni
043 A1A BK-IN
043 A1A BK-IN
043 A1A BK-IN
2. Press the [ MENU ] button to enter the Menu mode.
3. Rotate the [ SELECT ] knob to select Menu item "044
A1A DELAY
A1A DELAY
A1A DELAY".
A1A DELAY
A1A DELAY
A
:
DVICE
Press the [ SELECT ] knob momentarily to toggle the
Menu item display between "044 A1A
4. Start sending and rotate the [ CLAR/VFO-B ] knob to
adjust the hang time, as you prefer for comfortable
operation.
5. When you are finished, press and hold in the [ MENU ]
button for one second to save the new setting and exit
to normal operation.
You may adjust the center frequency of the receiver passband, and change the pitch of your offset CW carrier, to the tone
you prefer via the Menu item "045 A1A PITCH
1. Press the [ MENU ] button to enter the Menu mode.
2. Rotate the [ SELECT ] knob to select Menu item "045
A1A PITCH
A1A PITCH
A1A PITCH".
A1A PITCH
A1A PITCH
A
:
DVICE
Press the [ SELECT ] knob momentarily to toggle the
Menu item display between "045 A1A
3. Rotate the [ CLAR/VFO-B ] knob to select the desired
tone.
4. When you are finished, press and hold in the [ MENU ]
button for one second to save the new setting and exit
to normal operation.
A
:
DVICE
You may confirm the Spot tone frequency by pressing the
[ SPOT ] button. The frequency display will show the Spot
tone frequency.
Page 76
F
EATURES
CW D
ELAY
SEni
SEni
SEni
SEni").
044
044
044
044
044 A1A" and "DELAY
044 A1A
044 A1A
044 A1A
DELAY".
DELAY
DELAY
DELAY
CW P
ITCH
045 A1A PITCH". The tone may be varied between 300 Hz and 1050 Hz, in 50 Hz steps.
045 A1A PITCH
045 A1A PITCH
045 A1A PITCH
045
045
045
045
045 A1A" and "PITCH
045 A1A
045 A1A
045 A1A
PITCH
PITCH
PITCH
PITCH".
T
S
IME
ETTING
[ BK-IN ] Button
[ SELECT ] Knob
A
DJUSTMENT
[ SELECT ] Knob
T
:
ERMINOLOGY
CW Pitch: If you tuned to an exact "zero beat" on an in-
coming CW signal, you could not copy it ("Zero beat"
implies a 0 Hz tone). Therefore, the receiver is offset sev-
eral hundreds of Hz (typically), to allow your ear to detect
the tone. The BFO offset associated with this tuning (that
produces the comfortable audio tone) is called the CW
Pitch.
FT-950 O
[ MENU ] Button
[ CLAR/VFO-B ] Knob
[ MENU ] Button
[ CLAR/VFO-B ] Knob
M
PERATING
ANUAL

Advertisement

Chapters

Table of Contents
loading

Table of Contents