Display Indications - Yaesu FT-950 Operating Manual

D I
NDICATIONS ( L
ISPLAY
PROC
This indicator appears whenever the DSP Speech Pro-
cessor is activated.
MONI
This indicator appears whenever the transmit monitor
circuit is activated.
KEYER
This indicator appears whenever the internal CW keyer
is activated.
BK-IN
This indicator appears whenever CW break-in opera-
tion is activated.
NB
This indicator appears when the receiver's "short-du-
ration" Noise Blanker is activated.
This indicator will blink for three seconds, and there-
after appears continuously, when the receiver's "longer
pulse" Noise Blanker is activated.
NAR
This indicator appears whenever the receiver's narrow
IF DSP filter is engaged.
S/PO
On receive, this indicates the received signal strength,
from S-0 to S-9+60dB on receiving.
On transmit, it indicates the RF Power Output, from 0
to 150 Watts on transmit.
A :
DVICE
The S and PO meters can be set to the Peak-hold func-
tion via the Menu items "007 DISP PKH S
DISP PKH PO DISP PKH PO DISP PKH PO". DISP PKH PO DISP PKH PO
Multi Function Meter
The five Transmit Multi-Meter functions are listed
below.
ALC Indicates the relative ALC voltage.
SWR Indicates the Standing Wave Ratio
(Forward: Reflected), from 1.0 to 3.0.
ID Indicates the final amplifier drain current,
0 to 30 ampere.
VDD Indicates the final amplifier drain voltage
(nominal value: 13.8 V).
COMP Indicates the speech compressor level,
from 0 to 30 dB.
Page 24
007 DISP PKH S" and "008
007 DISP PKH S 007 DISP PKH S 007 DISP PKH S 008 008 008 008
)
S
EFT IDE
The function displayed is selected by repeatedly press-
ing the [ METER ] switch, to step through the available
meter displays. (ALC
ALC ALC ALC ALC
ALC .... )
ALC ALC
ALC ALC
A :
DVICE
The ALC and ID meters can be set to the Peak-hold
function via the Menu items "009 DISP PKH ALC
and "010 DISP PKH ID
010 DISP PKH ID 010 DISP PKH ID 010 DISP PKH ID". 010 DISP PKH ID
TUNER
This indicator appears when the internal Automatic An-
tenna Tuner is activated.
HI-SWR
This indicator appears if the directional coupler and
microprocessor detect an abnormally high SWR con-
dition (over 3.0:1) that cannot be resolved by the Au-
tomatic Antenna Tuner.
N :
OTE
If this indicator appears, check to be sure that you have
the correct antenna selected for the current operating
band. Also check the condition of the antenna, the co-
axial cable, and/or the connectors on the cable, to lo-
cate and correct the fault.
MIC EQ
This indicator appears whenever the Three-Band Para-
metric Microphone Equalizer is activated via the Menu.
REC
This indicator appears while the optional Voice
Memory Unit is recording your voice message, or the
Contest Keyer is recording your CW keying.
PLAY
This indicator appears while the optional Voice
Memory Unit is playing back the recorded voice mes-
sage, or the recorded Contest CW keying.
FT-950 O
SWR SWR SWR SWR SWR ID ID ID ID ID VDD VDD VDD VDD VDD COMP COMP COMP COMP COMP
009 DISP PKH ALC 009 DISP PKH ALC
009 DISP PKH ALC" 009 DISP PKH ALC
M
PERATING ANUAL