Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Lexmark 19Z0200 - X 860de 4 B/W Laser
Summary of Contents for Lexmark 19Z0200 - X 860de 4 B/W Laser
- Page 1 X860de, X862de, X864de Maintenance Guide August 2011 www.lexmark.com...
-
Page 2: Table Of Contents
Contents Maintaining the printer................3 Cleaning the exterior of the printer......................3 Cleaning the scanner glass........................4 Adjusting scanner registration........................4 Storing supplies............................5 Conserving supplies...........................5 Checking the status of supplies.........................5 Checking the status of supplies from the printer control panel ................. 5 Checking the status of supplies from a network computer................5 Ordering supplies............................6 Ordering toner cartridges ........................... -
Page 3: Maintaining The Printer
Maintaining the printer Periodically, certain tasks are required to maintain optimum print quality. Cleaning the exterior of the printer Make sure that the printer is turned off and unplugged from the wall outlet. CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer, unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding. -
Page 4: Cleaning The Scanner Glass
Cleaning the scanner glass Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images. Slightly dampen a soft, lint-free cloth or paper towel with water. Open the scanner cover. White underside of the ADF cover White underside of the scanner cover Scanner glass ADF glass... -
Page 5: Storing Supplies
Touch the up or down arrow until Scanner Manual Registration appears. Touch Scanner Manual Registration. Touch the left and right arrows to change the settings. Touch Submit. Storing supplies Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them. -
Page 6: Ordering Supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer. -
Page 7: Ordering Staple Cartridges
Ordering staple cartridges When Staples Low or Staples Empty appears, order the specified staple cartridge. For more information, see the illustrations inside the stapler door. Part name Part number Staple Cartridges–3 pack 25A0013 Ordering a cleaning kit Use the wet and dry wipes from the cleaning kit to clean the scanner glass and touch screen. Part name Part number Cleaning kit (wet and dry wipes) - Page 8 Grasp the handle and pull out the cartridge. Unpack a new cartridge. Warning—Potential Damage: When replacing a toner cartridge, do not leave the new cartridge exposed to direct light for an extended period of time. Extended light exposure can cause print quality problems. Firmly shake the cartridge side-to-side several times to redistribute the toner.
-
Page 9: Replacing The Photoconductor
Insert the new cartridge into the printer. Push the toner cartridge in as far as it will go. The cartridge clicks into place when correctly installed. Close the front door. Replacing the photoconductor You can determine approximately how full the photoconductor is by printing the printer settings configuration sheet. This helps you decide when you might need to order replacement supplies. - Page 10 When 84 Replace photoconductor or 84 Photoconductor low appears, order a new photoconductor immediately. While the printer may continue to function properly after the photoconductor has reached its official end‑of‑life, print quality significantly decreases. To replace the photoconductor: Turn the printer off. Open the front door.
- Page 11 Lower Side Door A. Pull the photoconductor out of the printer. Place the photoconductor on a flat, clean surface. Unpack the new photoconductor. Maintaining the printer...
- Page 12 Align and insert the end of the photoconductor. Remove the tape from the top of the photoconductor. Maintaining the printer...
- Page 13 Push the photoconductor as far as it will go. The photoconductor clicks into place when correctly installed. Close Side Door A. Maintaining the printer...
-
Page 14: Moving The Printer
Close the front door. Note: After you insert the photoconductor and close all the doors, the printer performs a motor cycle and clears the Replace Photoconductor warnings. The printer returns to the Ready state. Moving the printer Before moving the printer CAUTION—POTENTIAL INJURY: The printer weight is greater than 55kg (121 lbs), and requires at least four persons or a properly rated mechanical handling system to move it safely. - Page 15 Follow these guidelines to avoid personal injury or printer damage: • Use at least four people or a properly rated mechanical handling system to lift the printer. • Turn the printer off using the power switch, and then unplug the power cord from the wall outlet. •...
- Page 16 Place the tray into the printer. Remove the cable cover. Maintaining the printer...
- Page 17 Disconnect the optional drawer connector. Attach the cable cover. Lift the printer off the trays. Maintaining the printer...
-
Page 18: Moving The Printer To Another Location
Moving the printer to another location The printer and options can be safely moved to another location by following these precautions: • Any cart used to move the printer must have a surface able to support the full footprint of the printer. Any cart used to move the options must have a surface able to support the dimensions of the options.