Table of Contents
Advertisement
WALRB3P manual booklet
CHANGING VOLUME LOCK (cont'd)
Locking Volume Control To One Mode
(Global Volume Lock)
2.
Enter
-
-
and then press any mode key once (e.g.,
9
9
3
The
will blink twice.
LED
3.
Now, when you press
the selected device (e.g.,
of the mode you have selected.
Unlocking Volume Control For A Single Device (Individual Volume
Unlock)
1.
After performing Global Volume Lock (above),press a desired
mode key where you want volume to be unlocked (e.g.,
) and controlled within its own mode.
DVD/VCR
2.
Press and and hold
then release
SET
3.
Enter
-
-
and then press
9
9
3
four times.
4.
If desired, repeat steps 1 through 3 (of this section) for
each device that you want volume to be unlocked.
5.
After selecting a device that has volume unlocked (e.g.,
), pressing
DVD/VCR
device's volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting)
NOTE: Performing these instructions will restore independent volume control for all pro-
grammed devices (e.g., TV volume control in TV mode, VCR volume in DVD/VCR mode,
etc.).
1.
On the remote control, press and hold
light) blinks twice,then release
2.
Enter
-
-
and then press
9
9
3
blink four times.
3.
Volume will again be independently controlled according
to its default states for all programmed devices.
5/2/06
3:13 PM
Page 13
,
, or
, the volume of
VOL +
VOL -
MUTE
) will be controlled, regardless
TV
until the
(red light) blinks twice,
SET
LED
.
once. The
will blink
VOL -
LED
,
, or
will control the
VOL +
VOL -
MUTE
until the
SET
LED
.
SET
once. The
will
VOL +
LED
13
CLEARING CUSTOM PROGRAMMING
The One For All 3 Device Universal Remote Control contains an Operational
Feature Reset program. If desired, you can use it to clear custom program-
ming, except your setup codes and reassigned device keys, and reset them
).
to original factory settings.Also see Restoring Factory Default Settings below.
TV
I I M M P P O O R R T T A A N N T T : : E E x x e e c c u u t t i i n n g g t t h h i i s s p p r r o o g g r r a a m m w w i i l l l l e e r r a a s s e e a a l l l l y y o o u u r r c c u u s s t t o o m m s s e e t t t t i i n n g g s s f f o o r r
P P o o w w e e r r M M a a c c r r o o , , F F a a v v o o r r i i t t e e C C h h a a n n n n e e l l s s , , a a n n d d V V o o l l u u m m e e L L o o c c k k . .
1.
Press and hold
then release
2.
Enter
trol will return to normal operation.
RESTORING FACTORY DEFAULT SETTINGS
The One For All 3 Device Universal Remote Control also contains a Factory
Reset program that you can use to reset all custom settings and setup codes
to original factory settings.Also see Clearing Custom Programming above.
I I M M P P O O R R T T A A N N T T : : E E x x e e c c u u t t i i n n g g t t h h i i s s p p r r o o g g r r a a m m w w i i l l l l e e r r a a s s e e a a l l l l y y o o u u r r c c u u s s t t o o m m s s e e t t t t i i n n g g s s f f o o r r
P P o o w w e e r r M M a a c c r r o o , , F F a a v v o o r r i i t t e e C C h h a a n n n n e e l l s s , , V V o o l l u u m m e e L L o o c c k k , , R R e e a a s s s s i i g g n n e e d d D D e e v v i i c c e e s s , , a a n n d d a a l l l l
d d e e v v i i c c e e s s e e t t t t i i n n g g s s . .
1.
Press and hold
then release
2.
Enter
trol will return to normal operation.
(red
until the
(red light) blinks twice,
SET
LED
.
SET
-
-
. The
will blink twice. The remote con-
9
8
0
LED
until the
(red light) blinks twice,
SET
LED
.
SET
-
-
. The
will blink twice. The remote con-
9
8
1
LED
14
Hide quick links:
Advertisement
Table of Contents
