Huawei HG530 User Manual
  1. Manuals
  2. Brands
  3. Huawei Manuals
  4. Gateway
  5. HG530
  6. User manual
Huawei HG530 User Manual

Huawei HG530 User Manual

Home gateway
Hide thumbs Also See for HG530:
Table of Contents

Advertisement

Quick Links

See also: Instruction and Installation Manual
HUAWEI HG530 Home Gateway

User Guide

Advertisement

Table of Contents
loading

Related Manuals for Huawei HG530

Summary of Contents for Huawei HG530

  • Page 1: User Guide

    HUAWEI HG530 Home Gateway User Guide...

  • Page 2: Table Of Contents

    Contents 1 Warnings and Precautions ............1 2 Connecting the Cables and Getting Started ......4 2.1 Connecting The Cables .............4 2.2 Getting Started ................4 3 Setting the Network-Access Parameters ........ 6 3.1 Accessing the Network Through the Embedded PPP Dial-Up Software on the Device ..............6 3.2 Accessing the Network Through the PPP Dial-Up Software on Your Computer .................7...

  • Page 3: Warnings And Precautions

    1 Warnings and Precautions To use the device properly and safely, read these warnings and precautions carefully and strictly observe them during operation. Unless otherwise specified, the term "device" refers to the device and its accessories. Basic Requirements During storage, transportation, and operation of the device, keep it dry and prevent it from colliding with other objects.
  • Page 4 device immediately, power it off, remove all the cables connected to it, and then contact an authorized service center. During thunderstorms, power off the device, and then remove all the cables connected to it to prevent it from getting damaged due to lightning strikes. Precautions for Using Wireless Devices When using the device, ensure that the antenna of the device is at least 20 cm away from all persons.
  • Page 5 Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1 and it is tested and approved according to national or local standards. Safety of Children Keep the device and its accessories out of the reach of children. Otherwise, they may damage the device and its accessories by mistake, or they may swallow the small components of the device, causing suffocation or other dangerous situations.

  • Page 6: Connecting The Cables And Getting Started

    PHONE interface c. LINE interface 2.2 Getting Started To power on the HG530, press the power button on the side panel of the HG530. After you power on the HG530, the ADSL indicator blinks (for less than three minutes), which indicates that the HG530 is being activated. After the ADSL...
  • Page 7 Power and ADSL indicators turn solid on, which indicates that the HG530 is working properly.

  • Page 8: Setting The Network-Access Parameters

    Embedded PPP Dial-Up Software on the Device If you select this method for accessing the network, the HG530 starts to set up a dial-up connection automatically after the startup. You can access the network after you power on your computer. You do not need to install any special dial-up software on your computer or perform dial-up operations on your computer.

  • Page 9: Accessing The Network Through The Ppp Dial-Up Software On Your Computer

    1. Set the working mode of the HG530 to Bridge. 1) Log in to the Web-based configuration utility of the HG530 2) In the navigation tree on the left of the Web-based configuration utility, choose Basic >...
  • Page 10 2. Install and configure the PPP dial-up software on your computer. The PPP dial-up software is pre-installed on certain computer operating systems. To create a dial-up connection, do as follows (taking the Windows XP operating system as an example): 1) Choose Start > All Programs > Accessories > Communications > Network Connections.

  • Page 11: Configuring The Wireless Network Connection

    Windows XP operating system as an example): 1. Log in to the Web-based configuration utility. 2. Set the wireless network name and access password of the HG530. To set the wireless network name and the access password, do as follows (taking the authentication type WPA-PSK as an example): 1) In the navigation tree on the left, choose Basic >...
  • Page 12 After the password is verified, Connected appears on the icon of the wireless network in the wireless network list, which indicates that your computer is connected to the HG530 through wireless connection. 8) Close the Wireless Network Connection dialog box.

  • Page 13: Configuring The Device

    Web-based configuration utility, enter the new password, and then click OK. If you forget the user name or password that has been changed, you can restore the default settings of the HG530 by pressing and holding the Reset button for over six seconds. Then, the user name and password that are used for logging in to the Web-based configuration utility are restored to default values.

  • Page 14: Enabling Or Disabling The Wireless Network Function

    Function You can quickly enable or disable the wireless network function by pressing the WLAN button on the HG530. To enable the wireless network function, press and hold the WLAN button for over one second, and then release the button.

  • Page 15: Changing The Ip Address Used For Logging In To The Web-Based Configuration Utility

    Reset button on the rear panel. To restore the default settings, press and hold the Reset button for over six seconds after the HG530 is powered on, and then release the button. In addition, you can restore the default settings of the HG530 through the Web-based configuration utility.
  • Page 16 After the preceding operations, the current page jumps to the login page. You can log in to the Web-based configuration utility by entering the default user name and password.

  • Page 17: Faqs

    6 FAQs Can I use the terminal as a DHCP server? Yes, you can. The terminal incorporates the DHCP server software. How can I quickly restore the default settings of the terminal? To restore the default settings of the terminal, power on the terminal, press and hold the Reset button for a minimum of over six seconds, and then release the Reset button.
  • Page 18 1) In IP address, enter 192.168.1.100. Ensure that this IP address is unique and not used by other computers. 2) In Subnet mask, enter 255.255.255.0. 3) In Default gateway, enter 192.168.1.1. 6. Consult your network service provider about the IP address of the domain name server (DNS).
  • Page 19 3) Replace telephone lines. If the ADSL indicator still blinks, contact your network service provider. 3. Check whether the LAN indicator of the terminal is on. If the LAN indicator is off, perform further checks as follows: 1) Ensure that the network adapter of the computer is enabled. 2) Ensure that the network cable between the terminal and the computer is properly connected.
  • Page 20 2) Restore the default settings of the terminal. If the problem persists, contact your network service provider. 7. Check whether the proxy server of the Web browser is correctly configured. Take the Internet Explorer installed on a computer that runs Windows XP as an example.
  • Page 21 If the driver is improperly installed, install it properly. 5. Check whether the computer can receive the signals of a WLAN. Take a computer that runs Windows XP as an example. To check whether the computer can receive the signals of a WLAN, do as follows: 1) In the Control Panel window, double-click Network Connections to display the Network Connections window.
  • Page 22 If your computer is far from your terminal, the effects of the WLAN are affected. 4. Place your terminal and computer in another direction. 5. Do not use your terminal to access a WLAN during thunderstorms. What can I do if the WLAN of the terminal is not encrypted and the computer cannot access the WLAN? 1.
  • Page 23 5. If the problem persists, restore the default settings of the terminal. What can I do if Web pages often cannot be displayed during Web page browsing and can be displayed after the terminal is restarted? 1. Ensure that the terminal and other devices such as telephones or fax machines are connected to the telephone line through a splitter.

  • Page 24: Appendix

    The WAN connection is set up. Data is being transmitted. The HG530 works in routing mode. The WAN connection is set up. No data is being transmitted. The HG530 works in bridge mode or in routing mode. No WAN connection is set up.

  • Page 25: Interfaces And Buttons

    Button WLAN It is used to enable or disable wireless network function quickly. ON/OFF It is the power switch and is used to power on or power off the HG530. Power It is used to connect the power adapter.

  • Page 26: Default Settings

    Button You can press and hold the Reset button for Reset over six seconds to restore the default settings of the HG530. NOTE After you restore the default settings, your customized data is lost. Therefore, use this function with caution.
  • Page 27 Item Specification Entire-device power < 6 W consumption Ambient temperature 0°C to 40°C (32°F to 104°F) for operation Relative humidity for 5% to 95%, non-condensing operation Dimensions (L × W × 156.4 mm × 52 mm × 124.3 mm Weight About 245 g Standards ADSL...
  • Page 28 No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. The product described in this manual may include copyrighted software of Huawei Technologies Co., Ltd and possible licensors. Customers shall not in...
  • Page 29 Thus the descriptions herein may not exactly match the product or its accessories you purchase. Huawei Technologies Co., Ltd reserves the right to change or modify any information or specifications contained in this manual without prior notice or obligation.

Table of Contents