Sign in today to find solutions:

Don't have an account? Sign up

Delta Electronics Program Copy Card TP-PCC01 Instruction Sheet

Delta electronics program copy card instruction sheet.

Warning
TP-PCC01 doesn't support plug and play function. Please turn off power before plugging.
The voltage for TP-PCC01 is supplied from TP extension slot. Please ensure that plug direction is correct when connecting
TP-PCC01 to TP extension slot in case danger and damage on the device may occur.
Introduction
Model Name Explanation
Program Copy Card
Series
Electrical Specifications
Model Name
Item
Data Reserved Life / Times for
Writing In
Operation Temperature
Weight / Dimensions
Program Copy Card Functions
Compatible firmware version: TP05G/TP08G (V1.00 and above)
Using program copy card functions can copy the whole system parameters and application programs set in
one TP05G/TP08G to another TP05G/TP08G rapidly. It can save much time and manpower. The operation is
described in the following sections.
TP-PCC01 : Program Copy Card
TP
: Terminal Panel (TP05G/TP08G Series)
TP TP-PCC01
Step
(Copy TP program to TP-PCC01)
Turn the switch on the TP-PCC01 to
1
TP TP-PCC01
Insert the TP-PCC01 into the extension slot of TP
2
Apply power to TP
3
If the model type of TP does not match the
model type of the program set in TP-PCC01:
(TP05G program and TP08G program can't be
compatible with each other. It means that
TP05G program can't be opened and edited by
TP08G, and TP08G program can't be opened
and edited by TP05G either.)
4
TP will display:
TP series and TP-PCC01 is different
Press Enter to Confirm
TP series TP-PCC01
Press Esc to Exit
Press CLR to Erase TP-PCC01
Remove the program
TP will display:
TP-PCC01 will be Erased!
Press Enter to Confirm
Press ESC to Exit
If the model type of TP and the model type of
the program set in TP-PCC01 is matched.
TP will display:
Press Enter to Confirm
TP series TP-PCC01
Press Esc to Exit
Press CLR to Erase TP-PCC01
5
Press <Enter> key to confirm the "writing in"
operation.
When executing "writing in" operation,
TP will display:
TP series
TP-PCC01
Please wait!
"Writing in" operation is completed.
TP will display:
Please Remove the TP-PCC01 and
Reboot
Please turn the power of TP off and remove
TP-PCC01 from TP. At this time, all TP programs
and system parameters have been copied to
TP-PCC01.
Turn the power of TP off and then remove
TP-PCC01 when the message "Please Remove
6
the TP-PCC01 and Reboot" displays on the
screen of TP.
Dimension and Installation
U nits: mm
TP-PCC01
20 years / one hundred thousand times
0ºC ~ 55ºC
6g / 50.85×19.8×10 mm
TP-PCC01 TP
(Copy program in TP-PCC01 to TP)
Turn the switch on the TP-PCC01 to
TP-PCC01 TP
Insert the TP-PCC01 into the extension slot of TP
Apply power to TP
If there is no program in TP-PCC01.
TP will display:
The TP-PCC01 is Empty
TP-PCC01
TP series
is illegal
If the model type of TP does not match the
model type of the program set in TP-PCC01.
TP will display:
TP series and TP-PCC01 is different
Please Remove the TP-PCC01
and Reboot
If the model type of TP and the model type of
the program set in TP-PCC01 is matched.
TP will display:
Press Enter to Confirm
TP-PCC01
TP series
Press Esc to Exit
Press <Enter> key to confirm the "writing in"
operation.
When executing "writing in" operation,
TP will display:
TP-PCC01
TP series
Please wait!
"Writing in" operation is completed.
TP will display:
Please Remove the TP-PCC01 and
Reboot
Please turn the power of TP off and remove
TP-PCC01 from TP. At this time, all programs and
system parameters stored in TP-PCC01 have
been copied to TP.
Turn the power of TP off and then remove
TP-PCC01 when the message "Please Remove
the TP-PCC01 and Reboot" displays on the
screen of TP.
Note:
To avoid damage to TP-PCC01, when installing
TP-PCC01 into TP, please pay particular attention
to the installation direction of TP-PCC01 and ensure
that the side which there is a switch on it should be
up and toward the user.
ENGLISH

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: