Weekday / Weekend - Hunter 44660 Owner's Manual

Remote Sensor Programming (Cont.)
Your thermostat has the ability to operate by 3 different temperature settings with the remote sensor. You can choose to have
only the thermostat report temperature to your programs or hold settings, just the sensor, or an average of the the 2.This allows
you some custom control over the temperature in your home. If your bedroom is "the coldest/hottest room in the house", you
may decide to setup the remote sensor in your bedroom, and have your "sleep" program set to run by the remote sensor only,
or an average of the temperature displayed on the remote sensor and the thermostat. This will allow your system to heat/cool
your home to meet the sensor or average temperature between the sensor/thermostat.
To set a program to utilize the sensor options:
While you are setting up your programs you have the ability to set the temperature reporting location for that program by
either the thermostat, the sensor, or an average of the 2. To set this within the program, press the " sensor" button until you
reach the desired reporting combination. They are identified as
For details on your programming options, see the "Programming" section for 5/2 day, 7 day, or EVERYDAY.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.

Weekday / Weekend

Weekday / Weekend programming allows you to set all 5 weekdays in one program set, and the weekends in a second.
To program your thermostat in this manner:
1. Press the button to enter program mode. Weekdays will be displayed at the top of your screen and your hour and am/
program
pm indicator will flash. The system mode you are programming will be displayed at the bottom of the screen. (heat or cool)
2. Use the or to set the starting hour of program 1. Remember, to change between am and pm, you must pass the
12th hour, unless in 24 hour time.
3. To move to minutes, press the
4. Press the button again to change to the temperature setting. The
program
program.
5. Use the button to change to your alternate system mode (heat or cool) and set the temperature for it using the
system
or buttons. You may also wait until you have one mode programmed and return later to program the other.
Note: The times for heating and cooling within each program period will always be the same.
6. At this time, you can use the " sensor" or
program if you choose to change them.
7. Once you have finished with program 1, press
for program 2 and your system mode will be displayed at the bottom of the screen. Follow the same process throughout all
4 programs.
Once all 4 programs for your weekdays have been programmed, press
set. Weekend will now be displayed at the top of your screen. The same process will allow you to set all 4 programs for your
weekends.
Remember:
• The button will change between hour, minutes, set temperature, and programs 1-4.
program
• The and buttons will actually change the hour, minutes, and set temperature.
• " sensor" will change the reporting location for the temperature and
• Once complete, press
ret/clear
You may review your programs by using the
switch you from weekday or weekend program sets.
Note: Ignore the programs under Monday - Friday and everyday when reviewing your programs. These programs will not affect
weekday / weekend programming and can be ignored.
Once you are satisfied with your settings, press the
the alternate mode in the same manner. Once finished, if you wish to activate auto season changeover, use the
to change to "auto" mode.
2 . Programming (Cont.)
button again. or
program
button to change the temperature reporting location or fan setting for this
fan
to change to program 2. The hour and am/pm indicator will be flashing
program
to return to the main screen or wait 15 seconds.
button to move through the programs for weekday and weekends.
program
key to change heat or cool to the alternate mode. Proceed to set up
system
44008-01 • 02/10/10 • Hunter Fan Company
for sensor 1, for the thermostat and
will adjust the minutes in increments of 10.
and will adjust the temperature for that
to change to program 1 for the weekend program
prog/day
will change the fan between auto and on.
fan
6 6
to average the 2.
will
prog/day
button
system